Page is loading ...
XXXXXX
Xxxxx Xxxxxxxxx
e-mail: [email protected]
For latest product manuals:
www.omegamanual.info
Shop online at
omega.com
SM
User’s Guide
FLR-1600A and FLV-4600A Series
Water Flow Meters and Controllers
Servicing North America:
U.S.A.: Omega Engineering, Inc., One Omega Drive, P.O. Box 4047
Stamford, CT 06907-0047 USA
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660 Fax: (203) 359-7700
e-mail: [email protected]
For Other Locations Visit omega.com/worldwide
omega.com [email protected]
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains,
and reserves the right to alter specifications without notice.
Servicing North America:
U.S.A.: Omega Engineering, Inc., One Omega Drive, P.O. Box 4047
Stamford, CT 06907-0047 USA
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660 Fax: (203) 359-7700
e-mail: [email protected]
For Other Locations Visit omega.com/worldwide
omega.com [email protected]
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains,
and reserves the right to alter specifications without notice.
3
►
► use tap water or water with any biological components, minerals
these
Damage caused by impurity build
►
the manual for future reference.
►
1.
2.
and let water pass through while bleeding (if the unit is a controller
page 10 of the
3. Try not to get any water in-between the black electronics case and
these seams.
4. Tighten up both bleed screws, and then block the downstream
page 18
page 27
►
►
of standard gas
drop is 2 psig, going all the way to 20 psig drop in certain models.
Please see pages 47 and 49 of the manual.
4
7
8
8
9
10
11
12
12
13
14
14
14
14
14
16
17
18
Line Absolute Pressure 18
Line Temperature 18
Tare 18
19
Flashing Error Message 19
19
20
20
20
21
21
21
21
21
21
22
22
Rotate Display 22
23
23
24
26
27
27
28
28
PID Tuning 29
6
31
31
31
32
32
33
34
Data Format 36
37
38
39
41
43
43
44
46
47
48
Accessories 49
7
Power Jack
shown with the standard downstream
shown with the standard
8
leakage when the controller is being held closed by the spring force.
pressure sensor ports.
around the port threads.
9
10
1.
the threads.
2.
3.
though you may not see or hear it.
4.
Repeat steps 1-4 with the second bleed port.
11
4-20mA analo
1 2
3 4 5
6 7 8
1
2
3 Red
4
6 Green
7
8 Purple
12
Apply analog input to Pin 4 as shown on page 11.
signal to pin 4, with common ground on pin 8.
applied to pin 4, with common ground on pin 8.
applied to pin 4, with common ground on pin 8.
ohm resistor to ground.
7
6
5
4
3
2
1
8
5.12 Vdc
50 KOhm
Potentiometer
0-5 Vdc
4
8
13
9 8 7 6
9876
15 3 24
1 532 4
1
8
7
6
5
4
3
2
Pin Pin
Ground Ground 8
3 Transmit 3
2 Transmit
14
4-20 mA analog signal that can represent any measured parameter. With this
5
3
2
Purple
Red
Yellow
Purple
Red
Yellow
5
4
3
2
1
9
8
7
6
Unit C
Unit B
Unit A
Female Serial Cable Front
Purple (Ground)
Red
Yellow
16
monochrome display.
contrast.
780 mA @
17
The display shows, temperature
also be displayed if the meter was order
parameter will make that parameter
the primary display unit.
enter the display.
If your meter was ordered with the
display. Pushing
display.
display as soon as power is applied to the meter.
From you can interact
read manufacturer’s data.
Push
PEAK
=0.0
MENU/
MAINU
CCM
+0.0
CCM
TOTAL/
TIMER
BACK RESET
000.00
#C
+21.50
+0.00
CCM MENU
TARE V
PSIG
+13.60
CCM
WATER
+0.00
RS232
COMM
MFG
DATA
MAIN
MISC
2:05 h:m:s
18
This
as the primary displayed parameter.
The following parameters are displayed in
, pressing
the
pressure to the primary display.
Pressing the
primary display.
select
or
front of the desired scale.
temperature scale will be displayed on
the screen.
Pushing the
step in obtaining accurate measurements.
LN-DN
CANCEL SET
MODE
>#C
K
#F
#R
LN-UP
#C
+21.50
+0.000
CCM MENU
TARE V
CCM
WATER
PSIG
+13.60
+0.00
Volu Flow
19
manufacturer’s data.
RS232
COMM
MFG
DATA
MAIN
MISC
#C
+21.50
+0.000
CCM MAIN
TARE V
CCM
PSIA
+13.60
+
.
MODEL
INFO
BACK MAIN
MISC2
BACK
DEVICE/
UNITS
MAIN
MISC1
BACK MAIN
UNIT ID
A
BAUD
19200
the primary display.
Pressing switches the screen to the display.
An error message (
.
20
Access by pressing
or
on the display.
computer port.
Press
record the ID. Press Reset to return to the
See RS232 Communicaons (page 31) for
informaon about the streaming mode.
same baud rate. The default baud rate for
in front of
to select the baud rate that
matches your computer. The choices are
38400, 19200, 9600, or 2400 baud.
UP
BACK
RESET A
SET
UNIT ID
C
DN
DN
BACK SET
BAUD
UP
19200
BACK MAIN
UNIT ID
A
BAUD
19200
C
/
