Haier HWM65-187S User manual

Brand: Haier

Model: HWM65-187S

Category: Washing machines

Type: User manual

Haier HWM65-187S is a twin-tub washing machine with a full plastic cabinet that allows you to choose the water current and washing time, as well as the spinning time. The separate washing and spinning tubs, both made of plastic, are easy to clean and maintain. With its manual code SM HWM65-187S and edition date of 2008.04.17, this washing machine is a reliable choice for your laundry needs.

Twin-tub washing machine

Model HWM65-187S

SERVICE MANUAL

Manual code:SM HWM65-187S

Edition: 2008.04.17

Features

Full plastic cabinet

Choose water current and washing time

Choose spinning time

Sperate washing and spinning

Full plastic washing tub and spinning tub

CONTENTS

1.Contents 1

3. Specifications 3

4. 4

5. 5

6. Net dimension 6

7. 7

8. Parts and functions 10

9. Maintenance service and trouble shooting 11

10. Wiring diagram 15

Features 2

Safety precautions

Warning and cautions

Installation and accessory parts

FEATURES

Features

Full plastic cabinet

Choose water current and washing time

Choose spinning time

Sperate washing and spinning

Full plastic washing tub and spinning tub

Specification

Please insert the power cord into special

receptacle with rated voltage.Be sure to

use single-phase two pins receptacle.

The earthing terminal must be earthed

reliably.If possible,please adopt electric

leakage protector.

When the machine is normally using, please

put the power plug at the location easily to

be inserted and extracted by hand. Be sure

to pull the plug off when there'spower failure,

or the machine is being moved, cleaned or

when it is idle.

SAFETY PRECAUTIONS

If the power cord is bad, to avoid risk it is required to replace.

Keep the pin of the power plug clean.

In case the washing machine is installed

on ground with carpet , do not block the

ventilation hole with carpet.

Ventilation hole at

the bottom of the

washing machine

Do not use water hotter than 50 C .

Do not share one receptacle with other

electric appliances. Do not use it in

case that the power plug is damaged

or the inserting into the receptacle is

loose.

Do not wash water-proof laundries such

as the raincoat, bicycle shelter etc. To

avoid abnormal vibration during spinning.

Do not put the machine at damp place

like the bathroom . Never wash it with

water. Do not place wet laundries on the

control panel.

Do not stretch hands into the working

machine. It is dangerous even if the

rotation is slow. Take special care of

the children.

Handicapped or children without care

shall not use the machine.

Do not put any hot or heavy items

( such as the kettle with hot water )

on the washing machine.

Do not decompose, repair or alter the

machine by yourself.

Keep the machine away from direct

sunlight and heat source like the

heater.

Do not wash laundries with volatile

materials (such as thinner, petrol etc.).

Petro

inner

WARNING AND CAUTIONS

Figure 1

NET DIMENSION

INSTALLATION AND ACCESSORY PARTS

Unit mm

690

2.Do not step on or press the drain hose.

The drainage shall be smooth with the drain hose.

1.put the drain hose up to suitable position. .

Notes: the highest point of drain pipe should be

higher than

the water level of washing tub

for avoiding to siphon

phenomenon during drain.

<1.2m

0.7m<H

INSTALLATION AND ACCESSORY PARTS

Figure 1 indicates the ex factory installation

position of the drain hose.

Figure 1

Soft item

Extend the drain hose from the side of spin tub.

Put soft items on the ground. Lean the machine

down gently with the front surface facing the

ground. Take off the drain hose from the cabinet.

Take the hose out of the fixing groove.

(See to Figure 3).

Embed the drain hose into the groove along the side

of the spin tub in the order of (1)~(3), heading for the

side of the spin tub. (See to Figure 3).

Embed the drain hose into the groove with

hands. Take care not to damage the drain

hose in fastening the fixing clamp.

Soft item

Figure 2

Figure 3

Embed into the

groove in turn

Extend to the

spin tub side

Spin tub shaft

Bearing seat

Figure 8

Oilite bearing

Inner lining of

the bearing seat

Fastening screw

Fastening screw of

the brake wheel

Inner lining of the

brake wheel

Brake wheel

Spin motor shaft

Points of Attention in After-sales Service

Be sure to switch off the power during dismantling or repair.

Be sure to use insulated wiring terminals and insulation box in connection of the wires, and

crimp and fix to proper position with suitable tools.

In welding connections with electric iron, be sure to twist the wires before welding, and insulate

with insulation tapes.

In welding the wires with electric iron, be sure not to touch the resin part and insulation part of

each switch.

The inlay connection wires and terminals shall not be loose or drop.

Do not make the wires touch the moving parts like the belt, pulley of the motor, brake bar etc.

Do not make the wires touch the sharp edges and high-temperature area.

In case that there are metal parts with the wires, do not make the wires touch the metal parts.

Insulation materials are needed between them.

After assembly, the washing machine shall act normally. Check if it leaks and if the sound and

vibration are normal.

Dismantling and installation of the control panel component

Loosen the fastening screws. Pull towards the direction

indicated in the figure to dismantle the control panel. In

installation the beard shall lock into the installation hole

of the major frame. (Figure 6)

Dismantling and installation of the spin tub

frame component

Push the points marked with " " as indicated in

the figure and pull the spin tub frame towards

upper left direction to dismantle the spin tub frame

components. In installation, after set the rear side

of the spin tub frame to proper position, push the

four points marked with " " downwards by force

to resume its original position. (Figure 7)

Dismantling and installation of

the spin tub

Dismantle the spin tub frame component.

Loosen the fastening screw of the spin tub

shaft. The spin tub then can be taken out.

In installation, be sure to inlay the bulge of

the inner lining of the brake wheel into the

groove of the spin tub shaft. (Figure 8

Figure 6

Spin tub frame

Dismantle

Installation

Figure 7

INSTALLATION AND ACCESSORY PARTS

Dismantling and installation of the base frame

Dismantle the back cover. Loosen the wires. Loosen the

fastening screw of the spin tub shaft. Separate the shaft

from the brake wheel. Loosen the brake hook. Take off

the brake cable frame from the installation groove of the

twin-tub. Take off the V-belt. Take out the drain hose from

the groove of the base frame. Loosen the fastening screw

between the base frame and the cabinet to dismantle the

base frame component.

Dismantling and installation of the bearing seat

Once the bearing seat is taken off, it can not be utilized again. Therefore do

not dismantle

it as far as possible. In case that it has to be replaced, please dismantle it as

per following

sequence, then install a new bearing seat.

Dismantle the spin tub . Then pull out the bearing seat.

Cut off the inner lining claw inside the bearing seat with cutting pliers and

take it out.

Install the new bearing seat and inner lining.

Dismantling and installation of the bearing seat

Once the bearing seat is taken off, it can not be utilized again. Therefore do

not dismantle

it as far as possible. In case that it has to be replaced, please dismantle it as

per following

sequence, then install a new bearing seat.

Dismantle the spin tub . Then pull out the bearing seat.

Cut off the inner lining claw inside the bearing seat with cutting pliers and

take it out.

Install the new bearing seat and inner lining.

Figure 9

Right

Wrong

INSTALLATION AND ACCESSORY PARTS

Figure 10

PARTS AND FUNTIONS

Major frame

Base frame

Water-filling entrance

Wash selector

Wash timer

Control panel

Water level adjusting

lever

Pulsator

Wash tub

Wash tub cover

Drain hose

Overflow filter

Valve cover

Outer cover of the spin tub

Inner cover of the spin tub

Spin tub

Cabinet

Spin timer

Lint filter

(installed by user)

Insert the power plug , but the machine does not work

Wash part

YES

Switch on the power.

Replace the plug

or receptacle.

Replace with new power

supply cord.

Replace the fuse.

Inlay the connecting

wire again.

Check if the motor is good?

Replace the motor

Replace the wash timer

Replace the capacitor

Check if the capacitor

is good?

Poor contact or inferior

inside of the wash timer

Open the wash timer.

Check if the power source is available?

Check if the contact between

the plug and receptacle is good?

Check if the power supply

cord is good

Check if the fuse is good?

Check if the wash timer is opened ?

NO NO

Check if the inlay of

the connecting wire

terminal is good?

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Spin part

Check if the brake system

is detached?

Repair the brake system.

Check if the spin timer

is opened ?

YES

Switch on the power.

Open the spin timer.

Check if the power source

is available?

Replace the plug

or receptacle.

Replace with new

power supply cord.

Check if the contact between

the plug and receptacle is good?

Check if the power supply

cord is good?

Replace the fuse.

Inlay the connecting

wire again.

Check if the fuse is good?

Check if the micro-switch is closed?

Check if the inlay of

the connecting wire

terminal is good?

Replace the capacitor.

Check if the capacitor

is good?

Replace the motor.

Repair the micro-switch,

make it closed.

Check if the motor is good

MAINTENANCE SERVICE AND TROUBLE SHOOTING

There is metal rubbing noise in braking

The washing noise is too large

If the brake arm

has brake block ?

Add the brake or replace

the brake arm.

Is the motor noise large?

Is the motor fastened tightly?

Is the belt too loose

or too tight?

Replace the wash timer

Is the wiring of

the wash timer proper?

Is the radiating pulley loose?

Is the pulsator rubbing the

bottom of the twin-tub?

8.4 The pulsator only rotates towards one direction

YES

Replace the motor.

Fasten the motor tightly.

Adjust the tension of the belt.

Fasten the radiating pulley.

Adjust the gap between the

pulsator and the twin-tub.

Adjust the wiring to

proper position.

YES

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Trouble-shooting Answers to question

(If there's breakdown, please pull off the power plug before checking) The following

phenomena are not breakdowns sometimes. Please confirm again before

it to repair.

Phenomena The reason

The machine does

not act.

Is there power failure?

Is the power plug loose?

Is the pulsator twisted by

foreign materials?

Is the drain hose put down?

Is the drain hose blocked by

foreign material?

Are there laundries falling to

the outer side of the spin tub?

The draining

does not work

Are there hair pin, coins or

metal items brought inside

the tub?

Is the machine slanting?

Is the gland pressed evenly?

Are there laundries falling to

the outer side of the spin tub?

Are the laundries in spin tub

too much?

There's abnormal

sound and violent

vibration during

spinning

There's abnormal

sound during washing

Use it when the power is on.

Insert the power plug tightly.

Remove the foreign materials?

Put down the drain hose?

Remove the foreign material?

Please contact the after-sales

service department.

Remove the hair pin, coins or

metal items

Level the machine properly.

Pressed the gland evenly

Remove the laundries

Remove a little laundries

WIRING DIAGRAM

Actual Circuit Diagram

There is overload protector installed in the motor. In case that the motor is overload or meets

breakdown in working, the protector will act and stop the motor. When the breakdown is

removed, the motor will resume normal working.

Figure13

Figure 12

Spin timer

Safety switch

Orange

Purple

Grey

Spin

motor

Blue

Wash

motor

Red

Y ellow

Wash timer

Fuse

Brown

spin timer

microswitch

wash timer

wash

motor

capacitor

fuse

red

yellow

Grey

brown

blue

Yellow/green

orange

purple

yellow

blue

Cabinet

Control

Panel

spin

motor

Group

Haier Industrial Park, No.1, Haier Road

266101, Qingdao, China

http://www.haier.com

Sincere Forever

Haier HWM65-187S User manual

Brand: Haier

Model: HWM65-187S

Category: Washing machines

Type: User manual

Download PDF

report

Haier HWM65-187S User manual

Haier HWM65-187S User manual

Related papers

Other documents