2
Contents
Safety Instructions---------------------- ----------------------------- -------3
Precautions---------------------------------------------------------------------4
Features----------------------------------------------------------------------------4
Accessories------------------------- ----------------------------------------------5
Front Panel-------------------------------------------- ----------------------------5
Rear Panel--------------------------------------------------------------------------5
About Remote Control --------------------------------------------------------6
Start----------------------------------------------------------------------------7-8
Basic connections----------------------------------------------------------------------------------------------7
Preparation------------------------------------------------------------------------------------------------------------------------7
Connecting TV-Set--------------------------------------------------------------------------------------------------------------7
Fast Installation -------------------------------------------------------------------------------------------------8
Advanced Operation-------------------------------------------------------9-16
Main Menu -------------------------------------------------------------------------------------------------------9
Edit Channel------------------------------------------------------------------------------------------------------------------9-10
Installation-------------------------------------------------------------------------------------------------------------------10-11
System Setup---------------------------------------------------------------------------------------------------------------11-13
Tools--------------------------------------------------------------------------------------------------------------------------13-14
Game------------------------------------------------------------------------------------------------------------------------------14
REC---------------------------------------------------------------------------------------------------------------------------14-16
Appendix------------------------------------------------------------------------17-18
Maintenance ---------------------------------------------------------------------------------------------------17
Specifications -------------------------------------------------------------------------------------------------17
Troubleshooting ----------------------------------------------------------------------------------------------18
3
Safety Instructions
Dear customer,
Thank you for purchasing this DVB Terrestrial Receiver. Please read this manual carefully before
operating your product and pay close attention to the precautions which are mentioned below.
This product only can be operated where the mains supply is ~165-264V, 50Hz.
To avoid fire and electric shock, do not expose this equipment to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquid,
such as vases, shall be placed on the apparatus.
To reduce the chance of fire, electric shock, or annoying interference, use only the recommended
accessories.
The mains plug is used as the disconnect device, the disconnect device shall remain readily
operable。
Keep not less than 5cm distances around the apparatus for sufficient ventilation.
Keep the ventilation should not be impended by covering the openings with items such as
newspapers, table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like;
The label was silk-printed on the exterior of the bottom of the apparatus.
Correct Disposal of this product:
To reduce the chance of fire, electric shock, do not open the cover when it works.
This product has been manufactured to conform to the International Safety Standards.
Please peruse the following safety precautions before use.
OVERLOADING
Do not overload a wall outlet, extension cord or adapter as this may result in fire or electric shock.
CLEANING
Disconnect the product from the wall outlet before cleaning. Do not use any aerosol products to
clean the product. Dust the outer surface with a cloth lightly dampened with water (no solvents).
CONNECTING TO ANTENNA
Disconnect the product from mains before connecting or disconnecting to antenna. Otherwise, it
may damage the product and antenna.
CONNECTING TO TV SET
Unplug the power cord when connecting or disconnecting to TV Set. Otherwise, it may damage the
product and antenna
EARTHING
The antenna cable must be earthed to the antenna system and the Earthing System must comply
with the local Electric Safety Standards.
LOCATION
The DVB-T is designed for indoor use only. Do not install the product where it may expose to bright
light or direct sunlight.
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
4
Precautions
Peruse the following precautions before using.
Power Cord Protection
Please complaint the following regulations to
avoid malfunction, fire and electric shock or other
damage to human body.
Make sure to connect and disconnect the
power cord with holding the plug.
Do not connect or disconnect the AC power
with wet hands.
Separate the AC power cord from heating
appliances as distance as possible.
Do not stack any heavy objects on the AC
power cord．
Do not repair or reconstruct the AC power
cord without authorization.
Clean the plug regularly.
Cut off the power and disconnect the AC cord
immediately if the product has been dropped
or damaged.
Cut off the power and disconnect the AC cord
immediately if you find the product is
smoking, burning or noisy.
Location
Do not install the product in following
locations,
Where it may expose to direct sunlight or
heat resources such as heat register and
stove.
Ambient temperature over 35°C or ambient
atmospheric moisture over 90%.
Dusty place.
Where it may influence by magnetic field or
static electricity.
Where it may subject to physical shock,
vibration or dropping.
Non-use Periods
Switch the product to standby status or turn
off the power when the product will not be
used. Unplug the power cord from the AC
outlet when the product will be idle for a long
period of time.
Do not insert fingers or other objects into the
product
It may damage the product or even hurt
human body by touching any internal parts of
the product because of high voltage.
Do not dismantle the product.
Do not stack any object on the product.
Keep water and magnetic things away
Contact with liquid may cause serious
damage, please keep the product away from
it.
Keep product far away from magnetic things,
such as speaker and so on.
Position
Place the product on a horizontal surface. Do
not stack heavy things on it.
Do not place the product beneath the
magnifier or other devices that emit heat.
Signal Interference
Under the condition of TV signal receive
situation, TV Set may get signal interference
when you are watching a TV program with
the DVB-T on. This is not means that the
product or the TV Set is malfunction. Please
turn off the DVB-T while watching the TV.
Features
Fully MPEG-2 / DVB-T/H.264 Compliant
7 MHz and 8MHz Bandwidth for optional
Multi-language support
Auto scan/ Manual Scan
Support YUV/RCA Output
Digital Coaxial Output
Electronic Program Guide（EPG）
5V DC Antenna Compliant
USB 2.0
USB Upgrade
5
Accessories
After unpacking, Please find out the following accessories:
Remote control one piece
User Manual one piece
Batteries (AAA) two pieces
USB Cable(0.8M) one pieces
Front Panels
1. Standby Button
2.
CHButton
3.
CHButton
4.
IR Receiver Window
5. LED Display Window
6.
Power/ Standby Indicator
7.
Signal Indicator
8.
USB Port
Rear Panel
1. AC IN
2. YPbPr Video Output Socket
3.
Digital Coaxial Output Socket
4.
LOOP OUT Socket
5. RF IN
6.
RCA Audio/Video Output Socket
NOTE
In order to avoid electric leakage and shock caused by scratched power cord, please unplug the
power cord from the wall outlet and keep it orderly if the product is not going to be used for a long period
time.
6
About Remote Control
Remote control Name Descriptions
1 STANDBY Switch your device on from
standby mode.
2 TV/R Switch between TV and Radio
mode.
3 SUB-T Display subtitle.
4Numeric
Buttons
Select channel or programming
parameters. Press numeric button
0 to switch to sleep mode.
5 FAVOR Switch to favorite channels.
6 MENU Enter in setup interface.
7Navigation
Button-Up Skip to previous channel.
8Navigation
Button-Left Turn down volume.
9 OK Display channel list on screen.
Confirm selection.
10 Navigation
Button-Down Skip to next channel.
11 INFO Display information bar of current
service.
12 PVR Switch to PVR mode.
13 USB Switch to USB mode.
14 PREV Back to previous.
15 NEXT Skip to next.
16 F.REW Fast backward.
17 FF Fast forward.
18 REC Switch to REC mode.
19 STOP Stop playing.
20 PAUSE/PLAY Make a pause. Start watching
21 SLOW Slow down the speed while
playing.
22 Navigation
Button-Right Turn up volume.
23 EXIT Exit from current menu.
24 LAST Back to last channel.
25 EPG Display Electronic Program Guide
information of current channel.
26 TEXT Display text information of
current channel.
27 AUDIO Shift sound track.
28 MUTE Enable or disable the audio.
7
Start
Basic Connections
Preparation
All equipments must be connected according to this user manual.
Switch off this product and other equipments before connecting
Read the User Manual carefully before connecting other equipments
Plug the Audio and Video cable correctly
When connecting this product with TV set, only one kind of video output format will be accepted.
Please choose a corresponding video output mode for the product, otherwise the image will be
distorted.
NOTE
Users can choose any proper video output formats according to the TV socket and personal
requirements.
Connecting TV-set (Figure A)
1. Antenna (Not included)
2.
TV Set (Not included)
3.
DVB-T Receiver
4. AV cable for connecting TV set and DVB-T receiver (Not included)
5. YUV cable for connecting TV set and Amplifier. (Not included)
6. AC IN
8
Start
Fast Installation
Connect this unit and other apparatus according to “BASIC CONNECTIONS”. Plug the power cord,
press [STANDBY] button and wait “Welcome” window appears:
1.
Use [CH▲/▼] button to select item and [VOL◄/►]
button to change items.
2.
The default OSD Language is “English”, Region is
“German”, Display Mode is “PAL” and Aspect Mode is
“Auto”.
3. Move cursor to ”OK” and press [OK] button to start
auto search.
4.
Press [EXIT] button to back to channel list after auto
search has been done. Press [OK] button to display
channel list, use [CH▲/▼] button to select channel
and press [OK] button to enjoy watching.
If the “Welcome” window does not appear:
5. Press [MENU] button, move cursor to “Tools” and
press [OK] button to enter in its interface to load
factory default. Default password is “0000”. (This step
must be done at first use or after upgrade.)
6.
Choose “Yes” to start load factory default as showed
in the picture.
7. After the factory default has been done, wait
“Welcome” window and please operate according to
step 1, 2, 3 and 4.
Read Advanced Operation for more details.
9
Advanced Operation
Menu Operation
Main Menu
Press [MENU] button to browse the Main Menu including 6 submenus which are listed below:
◆Edit Channel
◆Installation
◆System Setup
◆Tools
◆Game
◆REC
Use [▲/▼] button to select item, press [OK] button to enter in its setup interface. Press [EXIT] button
to quit current menu.
Notes
1. The four navigation buttons ([▲/▼/◄/►]), [OK] and [EXIT] button have same functions in all
levels menus.
2. Some buttons have different functions in different menus. Please find out according to the screen.
3. Programmable buttons (which with color) functionality depends on the menu that is active at the
press moment. Please find out according to screen.
1. Edit Channel
Move cursor to “Edit Channel” and press [OK] button
to enter in its submenu. There are 3 options which are
listed below.
TV Channel List
Radio Channel List
Delete All
1.1 TV Channel List
Move cursor to “TV Channel List” and press [OK]
button to enter in its setup interface.
Use [CH▲/▼] button and press [OK] button to
confirm. Use programmable buttons (which with color) to
set up according to screen.
Favor button works only when the favorite channels
have been set. Default Password is: 0000.
Lock: Press [RED] button to lift the “Lock” icon. Use
[CH▲/▼] button to select channel and press [OK]
button to lock, press [OK] button again to cancel lock.
Press [EXIT] button to quit current menu and save
according to screen.
Skip: Press [Green] button to set the chosen TV program to be skipped when using [CH/]
button to choose programs.
Move: Press [YELLOW] button to move the channel. Choose channel first, move channel by
pressing [CH▲/▼] button and [OK] button to confirm. Press [EXIT] to quit current menu after setup
has been done. Save according to screen.
Edit: Press [BLUE] button to edit the program. In “Edit” interface, press [RED] button to sort
channels by Name (A-Z)/Name (Z-A)/Free/Scramble/Lock/Default; press [GREEN] button to edit
(rename) the chosen channel; press [BLUE] button to delete the chosen channel.
1.2 Radio Channel List
All found radio channels will be listed here.
Refer to the operation of TV Channel List (Item 1.1) for detailed instructions.
10
Advanced Operation
1.3 Delete All
Delete all TV and radio programs according to the
screen.
2. Installation
Move cursor to “Installation” and press [OK] button
to enter in its submenu. There are 4 options which are
listed below.
Auto Scan
Channel Scan
Aerial Adjustment
LCN
2.1 Auto Scan
Move cursor to “Auto Scan” and press [OK] button to
enter in its submenu.
FTA (Free Program): Yes/No.
Search: Move cursor to “Search” and press [OK]
button to start channel search. Press [EXIT] button to
stop searching and quit from current menu.
2.2 Channel Scan
Move cursor to “Channel Scan” and press [OK] button
to enter in its submenu.
Scan Mode: By Channel and By Frequency.
Scan Band: VHF and UHF.
Ch No. : Channel 5~12 (VHF) and Channel
21~69(UHF)
Frequency: 174~230 MHz (VHF), 470~862 MHz
(UHF). (The frequency system will be set
automatically according to regions.)
Band Width: 6MHz, 7 MHz and 8 MHz.
Search: Move cursor to “Search” and press [OK]
button to start search. Press [EXIT] button to stop searching and quit from current menu.
Notes
1. The “Scan Band” and “Ch No.” will be available only when “By Channel” is selected in Scan
Mode.
2. The “Frequency” and “Band Width” will be available only when “By Frequency” is selected in
Scan Mode.
11
Advanced Operation
2.3 Aerial Adjustment
A 5V (30mA) antenna is needed in “Tuner power on”
mode.
Tuner power: On/Off
2.4 LCN
The channels will be listed according to signal flow if
the LCN mode is on, otherwise the channels will be listed
normally.
LCN mode: ON/OFF
Note: Please set LCN in “OFF” mode in LCN
deactivated countries.
3. System Setup
Move cursor to “System Setup” and press [OK] button
to enter in its submenu. There are 8 options which are
listed below.
Language
TV System
Local Time Setting
Timer Setting
Parental Lock
OSD Setting
Favorite
Other
3.1 Language
Choose “Language” and press [OK] button to enter in
its setup submenu. Use [VOL/] button to change
options.
Language: English, French, Deutsch, Italian, Spanish,
Russian, Turkish, Polish, Arabic, Estonian, Greek,
Lithuanian, Persian and Croatian.
First Audio: English, French, Deutsch, Italian, Spanish,
Russian, Turkish, Polish, Arabic, Estonian, Greek,
Lithuanian, Persian and Croatian.
Second Audio: English, French, Deutsch, Italian,
Spanish, Russian, Turkish, Polish, Arabic, Estonian,
Greek, Lithuanian, Persian and Croatian.
Subtitle Language: English, French, Deutsch, Italian, Spanish, Russian, Turkish, Polish, Arabic,
Estonian, Greek, Lithuanian, Persian and Croatian.
Teletext: English, French, Deutsch, Italian, Spanish, Russian, Turkish, Polish, Arabic, Estonian,
Greek, Lithuanian, Persian and Croatian.
3.2 TV System
Video Resolution: 576i/480i
Aspect Mode: Auto/4:3 LB /4:3 PS/ 16:9
Video Output: CVBS/RGB
12
Advanced Operation
3.3 Local Time Setting
Region: France/German/Hong-
Kong/Italian/Poland/Russia/Singapore/Spain/Sweden/
Taiwan/United
Kingdom/Croatia/Argentina/Australia/China/Denmark/
Finland
GMT Usage: OFF/User Define/By Region.
GMT Offset: GMT+12:00~GMT-11:30.
Summer Time: ON/OFF
Date: Enter in its setup interface, use [VOL◄/►]
button to move the cursor and numeric buttons to
input. Press [OK] button to confirm imputation.
Time: Enter in its setup interface, use [VOL◄/►] button to move the cursor and use numeric
buttons to input. Press [OK] button to confirm imputation.
Notes
1. “GMT Offset” is only activated in “User Define” mode.
2. “Summer Time” is only activated in “By Region” mode.
3. “Date” and “Time” is only activated when “GMT Usage” in “OFF” mode.
3.4 Timer Setting
Timer Mode: OFF/Once/Daily/Weekly/Monthly
Timer Service: Channel/Record. (It’s deactivated when timer mode is off.)
Wakeup Channel: The system will start automatically once the Timer Mode is activated.
Wakeup Date: Set up time to wakeup. Use navigation buttons and numeric buttons to set up date.
Wakeup Time Set up time to wakeup. Use navigation buttons and numeric buttons to set up time.
Duration: Set up the length of an alarm. Use navigation buttons and numeric buttons to set up time.
Note: Wakeup function is deactivated when LED power indicator goes green.
3.5 Parental Lock
Default password is “0000”.
Menu Lock: OFF/ON
Password will be required for all levels of menu if the
menu lock is ON.
Channel Lock: OFF/ON
Password will be required for locked channels.
Parental Lock: OFF/4-18 years, total 16 levels
New Password
Confirm Password
Use numeric buttons to set up password.
3.6 OSD Setting
OSD Time out: 1-10 seconds.
OSD Transparency: OFF/10%/20%/30%/40%.
Load Default OSD Setting
13
Advanced Operation
3.7 Favorite
Totally 8 groups for optional.
Choose “1 Fav group 1” and press [OK] button to
rename it. Use navigations button to input according to
screen.
Press [EXIT] button to quit.
3.8 Other
Move cursor to “Other” and press [OK] button to enter
in its setup interface.
Sleep Timer: OFF/10 Min/30 Min/60 Min/90 Min/120
Min.
Auto Standby: On/OFF
4. Tools
Move cursor to “Tools” and press [OK] button to enter
in its submenu. There are 5 options which are listed below.
Information
Load Factory Setting
Upgrade By USB
USB Device
Remove USB device safely
4.1
Information
Move cursor to “Information” and press [OK] button to
display information of the device.
4.2
Load Factory Default
Move cursor to “Load Factory Default” and press [OK]
button to load factory default. The default password is
“0000”.This step must be done at first time use or after
upgrade. Please operate according to screen.
14
Advanced Operation
4.3
Upgrade By USB
Move cursor to “Upgrade by USB” and press [OK]
button to enter in its submenu.
Upgrade Mode
All Code: All software of this device.
Main Code: Logo of this device.
Radio back: Default setup of this device.
Upgrade File
Start: Move cursor to “Start” and press [OK] button
upgrade.
Note: Do not cut off power supply while upgrading,
otherwise it may destroy the device.
4.4
USB Device
Move cursor to “USB Device” and press [OK] button to enter in its submenu. Use [INFO] button to
shift between Music/Image/Video/Record modes.
4.5
Remove USB Device Safely
Choose “Remove USB Device Safely” and press [OK] button to carry out this action. A window will
displayed to ask you confirm to remove the USB device. Press [OK] button to confirm remove, [EXIT]
button to cancel.
5. Game
Move cursor to “Game” and press [OK] button to enter
in its submenu. There are 3 options which are listed below.
Tetris
Othello
Sudoku
Operate according to screen.
6. REC
Move cursor to “REC” and press [OK] button to enter
in its submenu. There are 5 options which are listed below.
Record Manager
DVR HDD Information
HDD Format
DVR Configuration
Jump
Notes:
Password will be required if the menu is locked. The
default password is “0000”.
Press [REC] button to start recording video. Press [STOP] button to stop. Please operate according
to screen.
REC mode is deactivated in standby mode.
15
Advanced Operation
6.1
Record Manager
Move cursor to “Record Manager”and press [OK]
button to enter in its setup interface. The record time,
capacity and format will be displayed in the menu. Find
further operation according to screen.
Lock: Press [GREEN] button to lock recorded video.
Password will be needed to open locked recorded
video.
Delete: Press [BULE] button to delete recorded video.
Please operate according to screen.
Rename: Press [RED] button to rename the recorded
video. Please use navigation buttons and numeric buttons to input. Save according to screen.
Notes
1.
Press [PVR] button to shift to “Record Manager” interface directly.
2.
Use [CH▲/▼] button to select recorded video and press [OK] button to play. It will back to “Record
Manager” interface automatically when the video is finished or press [EXIT] button.
TIPS
Press [PLAY] button to have a preview.
Press [OK] button to watch recorded video by full screen.
Press [PAUSE] button to make a pause while playing.
Press [STOP] button to stop playing.
There are 5 options, ×2, ×4, ×8, ×16, ×24 in “Fast Backward” and “Fast Forward” mode.
There are 3 options, ×1/2, ×1/4, ×1/8 in “Slow Forward” mode.
Press [INFO] button twice to open “HDD Record List” and press [OK] button to watch in full screen
while playing,
Move cursor to “DVR HDD Information” and press [OK] button to display information of disk.
6.2
DVR HDD Information
Move cursor to “Disk Information” and press [OK] button to
display information of disk.
6.3
HDD Format
Move cursor to “HDD Format” and press [OK] button
to enter in its setup interface to format disk.
6.4
DVR Configuration
Move cursor to “DVR Configuration” and press [OK]
button to enter in its setup interface.
Time Shift: ON/FF
Time shift to Record : ON/OFF
16
Advanced Operation
Tips for record real-time channel program.
Connect USB device with receiver.
Turn on “Time Shift” mode.
Press [PAUSE] button to stop the TV program and the receiver will start recording as much as
the USB device capacity is. Press [PLAY] button to continue watch the program from the
stopped.
Use [F.REW] and [F.FWD] buttons to forward or backward of recorded program. There are 5
options, 2、×4、×8、×16 and ×32.
Press [INFO] button twice to enter in “HDD Record List” interface, choose one of it and press
[OK] button to watching by full screen.
The recorded program will be eased automatically once channel has been shifted.
Tips for record video
Connect USB device with receiver.
Press [REC] button to start recording program.
Press [STOP] button to stop recording.
The receiver will start recording as much as the USB device capacity is.
Recorded video will be stored in the disk.
6.5
Jump
Move cursor to “Jump” and press [OK] button to enter
in its setup interface. There are 5 options which are listed
below.
30sec
1min
5min
10min
30min
Note: “Jump” function is only activated to non-real-time
program. Use [VOL◄/►], [PREV] and [NEXT] buttons to
operate.
Tips
While using [VOL◄/►] button:
The screen will jump to the time as set, requiring [OK] button to confirm the jump.
While using [PREV] and [NEXT] button:
The screen will jump to the time as set directly.
17
Appendix
Maintenance
◆Unplug the power cord before maintenance.
◆Keep the product surface clean. Please use a piece of soft cloth to clean the outer if it’s dirty.
◆Do not use any chemical products like Alcohol or dilution to clean the product.
◆Refer all servicing to a qualified service agent.
Specifications
Notes
The data for weight and size are approximations only.
Specifications are subject to change (by manufacturer) without notice.
Item
s
Features
High
Frequency
Tuner
Input Frequency Range 174～230, 470 ~~ 862MHz (VHF&UHF)
Bandwidth 7 or 8 MHz
Input Signal Level －75～－20dBm
RF Input Connector IEC169－2, Female
Input impedance 75Ω
Demodulation
Mode
Waveform COFDM （Code Orthogonal Frequency Division
Multiplexing）
Demodulation QPSK，QAM16，QAM64
Transmission Mode 2K，8K
Guard interval 1/4, 1/8, 1/16, 1/32
Code
rate
1/2,
2/3,
3/4,
5/6,
7/8
Video, Audio
Decoding
Video decoding ISO/IEC13818-2 MPEG2 （MP@ML ）/ MPEG-4 AVC
/H.264
Compatible
Video resolution 720×576（PAL）＠25Hz；720×480（NTSC）＠30Hz
Audio decoding MPEG-1、2 layer 1 & 2
Audio Track Stereo, Monophony (L, R)
Audio Sample rate 32，44.1, 48KHz
USB
USB Port USB2.0
Format
MP3/JPGE/BMP
/OGG
Power Supply 5V 1000mA
Power
Input Power 230V,50Hz
Input Power Range ~165-265V, 50Hz
Power
C
onsumption
≤
8
W
Max Consumption ≤ 2 W
Work
Environment
Temperature 0~40℃
Humidity
<95%
Dimensions Weight ＜2．5Kg
Size 266 mm×165mm×39mm
18
Appendix
Troubleshooting
Look through the following table about the possible troubles and you may find answers before
request service. It may help you to resolve the problems with some easy operations according to this
table. If something goes wrong with the receiver and can’t back to normal, please cut off the power for
few minutes and restart the product. If the problem remains and proves to beyond your capability, you
had better hand it over to a qualified service agent.
The integrated circuits are easily breakdown by static. Make sure the antistatic protection has been
well taken before maintenance.
Troubles
Possible
Cause
Suggested
Solutions
No power The power cord has not been well connected
Plug the power cord into the outlet
tightly and turn on the power; if still no
power, turn off the power again, and
wait for 5-10 minutes, then restart again.
Can
not
scan
programs
The antenna is not adjusted well Adjust the antenna or use an outdoor
antenna
Antenna
incorrectly
Use
an
antenna
with
75
Ω
impedance
input
Parameter
input
incorrectly
Input
Frequency,
Bandwidth
parameter
correctly
No
picture
Output
cord
is
connected
incorrectly
Connect
the
output
cord
correctly.
If
the
problem
is
still
exit,
the
output
cord
may
damage.
The video output mode of the unit is different
from the mode of monitor Reset the mode
No Color The video output system of the unit is
different from the mode of monitor Reset the color system
Image
distortion at
channel shift
normal
The remote
control fails
to work
Batteries incorrectly installed Install the battery correctly
Batteries exhausted Replace the battery
Beyond
the
effective
operation
range
Operate
within
an
effective
range
The
remote
sensor
is
pointed
to
by
bright
light
.
Place
the
unit
elsewhere
for
a
change
Audio track
and subtitle
language
are not the
chosen
items
Has not chosen the right sound track Press the Audio button to shift the track
No sound
The unit is in a mute status Cancel the mute
Volume is too low Augment the volume
Cable is connected incorrectly Connect the cable correctly
No sound by
chance
There might be a short circuit Correct the output cable connection,
and turn on again.
In mute status Cancel the mute
Stay asleep Turn on the unit
Poor picture
quality Too much interferential signals Adjust the position of antenna.
No response May interfered by static Plug the power cord again
Flash
Drive
can
’
t
be
read
The
USB
cable
connected
incorrectly
Connect
the
cable
correctly.
The
flash
drive
’
s
current
is
too
heavy,
the
product
wouldn
’
t
afford
it.
Provide
external
power
source.
The
flash
drive
runs
self-protection
program
because
of
external
device
short
circuit.
Change
the
short
circuit
device
and
restart
the
product.
19
Address: Floor-809,West Tower, Coastal City,
Hai De 3 road, Nanshan Area, Shenzhen City, Guangdong Province,China
地址：（中国）广东省深圳市南山区海德三道海岸城西座 809 室
Tel: +86 755 216 79069
Mob: +86 159 893 964 29
Email:[email protected].cn
Inpax-china@inpax.com.cn
Web: www.inpax.com.cn
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
