ML Accessories VFRSHGICW User manual

Brand: ML Accessories

Model: VFRSHGICW

Type: User manual

This manual is also suitable for

INSTALLATION & MAINTENANCE MANUAL

VFRDGICxx / VFRSGICxx / VFRSHGICxx

These instructions should be read carefully and retained after installation by the

end-user for future reference and maintenance.

These instructions should be used to aid the installation of the following

products: VFRDGICxx / VFRSGICxx / VFRSHGICxx

GENERAL INSTRUCTIONS

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring

Regulations (BS7671) and current Building Regulations. If in any doubt, consult a qualiﬁed

electrician

• Please isolate mains prior to installation or maintenance

• Please note the IP (Ingress Protection) rating of this ﬁtting when deciding the

location for installation

• If used under insulation, the insulation should be laid unbroken over the ﬁtting (not packed

around it). Only mineral wool style insulation may be used

• This product is Class I and must be earthed

• The VFRDGICxx and VFRSGICxx series is IP20 rated, the VFRSHGICxx

series is IP65 (IP20 from above)

INSTALLATION

• Provide power to the required point of installation

• Cut a suitable hole in the mounting surface as per the cut-out details

(see Fig. 1) ensuring not to infringe with any joists, gas/water pipes or electrical cables

INSTRUCTIONS – VFRxxxx

These instructions should be read carefully and retained after installation by the end-user for future reference

and maintenance.

These instructions should be used to aid the installation of the following products:

VFRDGICxx / VFRSGICxx / VFRSHGICxx

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Please note the IP (Ingress Protection) rating of this fitting when deciding the location for installation

• If used under insulation, the insulation should be laid unbroken over the fitting (not packed around it).

Only mineral wool style insulation may be used

• This product is Class I and must be earthed

• The VFRDGICxx and VFRSGICxx series is IP20 rated and, the VFRSHGICxx series is IP65 rated

INSTALLATION

• Provide power to the required point of installation

• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas/ water pipes or electrical cables

Fig .1

• Fold-out the terminal bracket until it locks into position (see Fig. 2)

Part code

Cut-out

VFRDGICxx

72mm

VFRSGICxx

84mm

VFRSHGICxx

72mm

Part code Cut-out

VFRDGICxx 72mm

VFRSGICxx 84mm

VFRSHGICxx 70mm

• Fold out the terminal bracket until it locks

into position (see Fig. 2)

Replace Fig 2;

Replace Fig 3;

Fig. 1

Fig. 2

• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 3): L -

Live (brown), E - Earth (green/yellow), N - Neutral (blue). Two cables can be inserted into the push-fit

terminal block in order to achieve loop in / loop-out wiring

Fig. 3

• Secure the mains cable under the cable clamp by closing the lid tightly

• Lift both spring clips on the sides of the fitting and push into the ceiling (see Fig. 4)

Fig. 4

• Remove the bezel by turning anti-clockwise (see Fig. 5), insert a suitable GU10 lamp into the bezel,

and connect the lamp to the lamp holder

Fig. 5

• Insert the lamp into the body of the downlight and secure by turning the bezel clockwise. If using the

VFCFIPxx series, please ensure both gaskets are in place. One gasket is in the bezel and the other is

around the base of the fitting (see Fig. 6)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference

and maintenance.

These instructions should be used to aid installation of the following products:

VFCFBC / VFCFC / VFCFW / VFCFIPBC / VFCFIPC / VFCFIPW / VFCFTBC / VFCFTC / VFCFTW

SAFETY

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of

the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• Allow 50mm above and around the fitting for air dissipation (do not cover the fitting with insulation)

• This product is Class I and must be earthed

• The VFCFxx and VFCFTxx series are IP20 rated; the VFCFIPxx series is IP65 rated

INSTALLATION

• Provide power to the required point of installation

• Cut a suitable hole in the mounting surface as per the cut-out details (see Fig. 1) ensuring not to

infringe with any joists, gas/water pipes or electrical cables

Fig. 1

• Slot the terminal block into position on the fitting, and open the terminal access cover with the aid of a

flat-head screwdriver (see Fig. 2)

Fig. 2

Fig. 3

Fig. 4

• Open the terminal access cover with the aid of a slotted screwdriver (see Fig. 3)

• Connect the ﬁtting to the mains supply ensuring that correct polarity is observed

(see Fig. 4): L - Live (Brown), E - Earth (Green/Yellow), N - Neutral (Blue)

• Connect the luminaire to the mains supply ensuring the correct polarity is observed (see Fig. 3): L -

Live (brown), E - Earth (green/yellow), N - Neutral (blue). Two cables can be inserted into the push-fit

terminal block in order to achieve loop in / loop-out wiring

Fig. 3

• Secure the mains cable under the cable clamp by closing the lid tightly

• Lift both spring clips on the sides of the fitting and push into the ceiling (see Fig. 4)

Fig. 4

• Remove the bezel by turning anti-clockwise (see Fig. 5), insert a suitable GU10 lamp into the bezel,

and connect the lamp to the lamp holder

Fig. 5

• Insert the lamp into the body of the downlight and secure by turning the bezel clockwise. If using the

VFCFIPxx series, please ensure both gaskets are in place. One gasket is in the bezel and the other is

around the base of the fitting (see Fig. 6)

Replace Fig 4

Replace Fig 6

Fig. 5

Fig. 6

• Ensure the strain relief is used to secure the mains input cable

• Loop in/loop out wiring can be achieved with the push-ﬁt terminal block

• Lift both spring clips on the sides of the ﬁtting and push into the ceiling (see Fig. 5)

• Remove the bezel by turning anti-clockwise 45°, insert a suitable GU10 lamp into the lock ring

lamp clip and connect a lamp to the lamp holder (see Fig. 6)

Replace Fig 7

• Push the lamp and lock-ring up into position in the body of the downlight and secure the

lock-ring by turning clockwise 45°

• For VFRSHGICxx series, please ensure both gaskets are in place. One gasket is

pre-installed with the bezel and the second gasket should be installed around the

base of the ﬁtting (see Fig. 7)

• Switch on and check for correct operation.

Fig. 7

GENERAL

This product should be recycled in the correct manner when it reaches the end of its life.

Check local authorities for where facilities exist.

Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which

may damage the product.

This product is dimmable dependent on lamp type.

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install this product

in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper

use, or removal of the batch code will invalidate the warranty. If this product should fail

within its warranty period, it should be returned to the place of purchase for a free of

charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML

Accessories reserve the right to alter product speciﬁcation without prior notice.

ML Accessories Limited LU5 4LT

www.mlaccessories.co.uk

DCAUG21_V5

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

INTERNATIONAL

CONTACT DETAILS

RATED

ML Accessories VFRSHGICW User manual

Brand: ML Accessories

Model: VFRSHGICW

Type: User manual

This manual is also suitable for

Download PDF

report

ML Accessories VFRSHGICW User manual

This manual is also suitable for

ML Accessories VFRSHGICW User manual

Related papers

Other documents