ML Accessories NCLB12 is a self-ballasted LED T8 tube that is designed for use in a variety of lighting applications. It is IP65 rated, making it suitable for use in wet or dusty environments, and has a lifespan of up to 50,000 hours. The NCLB12 is easy to install and can be used to replace traditional fluorescent tubes. It is also dimmable, allowing you to adjust the light output to suit your needs. With its energy-efficient design and long lifespan, the NCLB12 is a great choice for a variety of lighting applications.
ML Accessories NCLB12 is a self-ballasted LED T8 tube that is designed for use in a variety of lighting applications. It is IP65 rated, making it suitable for use in wet or dusty environments, and has a lifespan of up to 50,000 hours. The NCLB12 is easy to install and can be used to replace traditional fluorescent tubes. It is also dimmable, allowing you to adjust the light output to suit your needs. With its energy-efficient design and long lifespan, the NCLB12 is a great choice for a variety of lighting applications.
INSTALLATION & MAINTENANCE MANUAL
NCLB12 / NCLB14 / NCLB15 / NCLB16 / NCLB22
NCLB24 / NCLB25 / NCLB26
These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
NCLB12 / NCLB14 / NCLB15 / NCLB16 / NCLB22 / NCLB24 / NCLB25 / NCLB26
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
Part code LED tube size QTY Length (ft) Length (mm)
NCLB12 T8 1 2 653
NCLB14 T8 1 4 1263
NCLB15 T8 1 5 1563
NCLB16 T8 1 6 1828
NCLB22 T8 2 2 653
NCLB24 T8 2 4 1263
NCLB25 T8 2 5 1563
NCLB26 T8 2 6 1828
INSTALLATION
NOTE: This fitting is designed and wired for self-ballasted LED T8 tubes requiring 230V AC
input voltage (not for use with fluorescent tubes).
• Provide power to the point of installation
• Unfasten clips either side of the fitting (see Fig. 1)
• Remove the diffuser
• Remove the baseplate by pinching the clips at two locations (see Fig. 2)
Fig. 1 (single fitting shown)
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location
for installation
• This product is Class I and must be earthed
• This product is IP65 rated
NCLB series
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
NCLB12/NCLB14/NCLB15/NCLB16/NCLB22/NCLB24/NCLB25/NCLB26
Part code
LED tube size
Length (ft)
Length (mm)
NCLB12
T8
2
653
NCLB14
T8
4
1263
NCLB15
T8
5
1563
NCLB16
T8
6
1828
NCLB22
T8 x2
2
653
NCLB24
T8 x2
4
1263
NCLB25
T8 x2
5
1563
NCLB26
T8 x2
6
1828
SAFETY
• Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
• This product is Class I and requires an earth
• This product is IP65 rated
NOTE: This fitting is designed and wired for self-ballasted LED T8 tubes requiring 230V AC input voltage (Not for use with
fluorescent tubes).
INSTALLATION
• Provide power to the point of installation
• Unfasten clips either side of the fitting (see Fig 1)
Fig 1 (single fitting shown)
• Remove the diffuser
• Remove the base plate by pinching the clips at two locations (see Fig 2)
Fig 2
Pinch at these points
Unfasten clips on both sides
• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any
gas/water pipes or electrical cables
• Connect the Live (brown), Neutral (blue) and Earth (yellow and green) via the three-way
terminal block (see Fig. 3)
NCLB series
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following products:
NCLB12/NCLB14/NCLB15/NCLB16/NCLB22/NCLB24/NCLB25/NCLB26
Part code
LED tube size
Length (ft)
Length (mm)
NCLB12
T8
2
653
NCLB14
T8
4
1263
NCLB15
T8
5
1563
NCLB16
T8
6
1828
NCLB22
T8 x2
2
653
NCLB24
T8 x2
4
1263
NCLB25
T8 x2
5
1563
NCLB26
T8 x2
6
1828
SAFETY
• Installation of this luminaire should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for installation
• This product is Class I and requires an earth
• This product is IP65 rated
NOTE: This fitting is designed and wired for self-ballasted LED T8 tubes requiring 230V AC input voltage (Not for use with
fluorescent tubes).
INSTALLATION
• Provide power to the point of installation
• Unfasten clips either side of the fitting (see Fig 1)
Fig 1 (single fitting shown)
• Remove the diffuser
• Remove the base plate by pinching the clips at two locations (see Fig 2)
Fig 2
Pinch at these points
Unfasten clips on both sides
Fig. 2
Fig. 3
• Mark the location of the fixing holes and drill the holes ensuring not to infringe with any joists, gas or water pipes
or electrical cables
• Connect the Live (brown), Neutral (blue) and Earth (yellow and green) via the three-way terminal connector (see
Fig 3)
Fig 3
• Fit an appropriate T8 LED tube (e.g. the ML Accessories T8LED series)
• Switch on power supply and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing.
Irreparable damage will occur if this instruction is not followed
GENERAL
The unit should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where
facilities exist
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the fitting
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the current
edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the warranty. If this
product should fail within its warranty period it should be returned to the place of purchase for a free of charge
replacement. ML Accessories does not accept responsibility for any installation costs associated with the replacement
product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specification without prior
notice.
Neutral (blue)
N
L
Live (brown)
E
Earth (green/yellow)
• Fit an appropriate T8 LED tube
• Switch on and check for correct operation
GENERAL
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations, improper
use, or removal of the batch codes will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
DCJUL21_V2
52
-
1
-
2
-
3
-
4
-
5
-
6
ML Accessories NCLB12 User manual
- Category
- Wall & ceiling mounts accessories
- Type
- User manual
ML Accessories NCLB12 is a self-ballasted LED T8 tube that is designed for use in a variety of lighting applications. It is IP65 rated, making it suitable for use in wet or dusty environments, and has a lifespan of up to 50,000 hours. The NCLB12 is easy to install and can be used to replace traditional fluorescent tubes. It is also dimmable, allowing you to adjust the light output to suit your needs. With its energy-efficient design and long lifespan, the NCLB12 is a great choice for a variety of lighting applications.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ML Accessories BL20ALED User manual
-
-
-
-
-
-
-
-
-
ML Accessories T8LB24 User manual
Other documents
-
Knightsbridge AC65270EM User manual
-
Knightsbridge T8 EMHF Series Installation & Maintenance Manual
-
-
-
-
ARC LKU3213CCT Installation guide
-
ARC LSO2202 Installation guide