Asus R680EI-IM-A User manual

Category
Motherboards
Type
User manual
Industrial Motherboard
R680EI-IM-A
ii
E22556
Revised Edition V4
August 2023
Copyright © 2023 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
iii
Contents
Chapter 1 Product overview
1.1 Package contents ......................................................................... 1-1
1.2 Features ........................................................................................ 1-1
1.3 Specifications ............................................................................... 1-2
Chapter 2 Motherboard information
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard layout ...................................................................... 2-2
2.3 Central Processing Unit (CPU) ................................................... 2-4
2.3.1 CPU installation .............................................................. 2-5
2.3.2 CPU heatsink and fan assembly installation ................... 2-7
2.4 System memory ........................................................................... 2-9
2.5 Jumpers ...................................................................................... 2-10
2.6 Connectors ................................................................................. 2-14
2.6.1 Rear panel connectors .................................................. 2-14
2.6.2 Internal connectors ....................................................... 2-16
2.7 Slot .............................................................................................. 2-25
Chapter 3 BIOS setup
3.1 BIOS Setup program .................................................................... 3-1
3.2 Main menu .................................................................................... 3-2
3.2.1 System Date [Day MM/DD/YYYY] .................................. 3-2
3.2.2 System Time [HH:MM:SS] .............................................. 3-2
3.3 Advanced menu ........................................................................... 3-2
3.3.1 LVDS Configuration ........................................................ 3-2
3.3.2 PCH-FW Configuration ................................................... 3-4
3.3.3 Trusted Computing ......................................................... 3-4
3.3.4 CPU Configuration .......................................................... 3-5
3.3.5 Graphics Configuration ................................................... 3-6
3.3.6 Power Management ....................................................... 3-6
3.3.7 PCI Express Configuration .............................................. 3-7
3.3.8 AMT Configuration .......................................................... 3-7
3.3.9 Super IO Configuration ................................................... 3-8
3.3.10 Serial Console Redirection ............................................. 3-9
3.3.11 SATA Configuration ...................................................... 3-11
3.3.12 VMD setup menu .......................................................... 3-11
iv
3.3.13 Network Stack Configuration ........................................ 3-11
3.3.14 USB Configuration ........................................................ 3-12
3.3.15 NVMe Configuration ...................................................... 3-12
3.3.16 Onboard Devices Configuration .................................... 3-13
3.3.17 Miscellaneous ............................................................... 3-13
3.3.18 APM Configuration ........................................................ 3-13
3.3.19 EZ-Flash ....................................................................... 3-15
3.3.20 IO Expander Configuration ........................................... 3-15
3.3.21 Watchdog Timer ............................................................ 3-15
3.4 Hardware Monitor menu ............................................................ 3-16
3.4.1 Smart Fan Mode ........................................................... 3-16
3.4.2 Smart Fan Function ...................................................... 3-16
3.5 Security menu ............................................................................ 3-16
3.5.1 Administrator Password ................................................ 3-16
3.5.2 User Password .............................................................. 3-17
3.5.3 Secure Boot .................................................................. 3-17
3.6 Boot menu .................................................................................. 3-18
3.7 Exit menu .................................................................................... 3-18
Appendix
Notices .......................................................................................................A-1
Service and Support .................................................................................A-5
1-1
Chapter 1: General information
1.1 Package contents
Check your industrial motherboard package for the following items.
1 x ASUS R680EI-IM-A Motherboard
1 x Serial ATA 6.0 Gb/s cable
1 x M.2 screw package
1 x ASUS I/O Shield
NOTE: If any of the above items is damaged or missing, contact your
distributor or sales representative immediately.
1.2 Features
Intel® socket 1700 for 12th Gen Intel® Core™ i9/ i7/ i5/ i3, Pentium®, and
Celeron® processorsup to 65W
Two Dual Channel DDR5 4800 MHz SO-DIMMs up to 64GB
4 x SATA 6.0 Gb/s, 3 x USB 3.2 Gen 2, 4 x USB 3.2 Gen 1, 6 x USB 2.0, 5 x
COM ports
1 x PCIe 5.0 x16 slot, 1 x M.2 (Key E, 2230) for WiFi/BT devices, 1 x M.2 (Key
M, 2242/2260/2280) with PCIe and SATA modes for SSD
Multi-display: 3 x DisplayPorts, 1 x HDMI™, 1 x LVDS/eDP
Chapter 1
Product overview
R680EI-IM-A
1-2
1.3 Specifications
(continued on the next page)
CPU
Intel® socket 1700 for 12th Gen Intel® Core™ i9/ i7/ i5/ i3,
Pentium®, and Celeron® processors
Supports up to 65W TDP
Chipset Intel® R680E Chipset
Memory
2 x SO-DIMM, max. 64GB, DDR5 4800 MHz, ECC support*
* ECC support is available only while using an Intel® Xeon®
processor and ECC memory.
Graphics
Integrated graphics processor - Intel® HD Graphics support
Multi-VGA output support: DP/HDMI™/eDP/LVDS ports
- Supports 3x DisplayPort 1.4 outputs with a maximum
resolution of 4k
- Supports HDMI™ output
- Supports either eDP or LVDS output (Switched by
BIOS)
Expansion slots
1 x PCI Express 5.0 x16 slot*
1 x M.2 socket 1 (Key E, 2230) with PCIe and CNVi modes
for WiFi/BT devices
1 x M.2 socket 3 (Key M, 2242/2260/2280) with PCIe and
SATA modes
* Supports PCIe bifurcation (16x to 8x+8x).
Storage
4 x SATA 6.0 Gb/s ports (Supports RAID 0,1,5,10)
1 x M.2 socket 3 (Key M, 2242/2260/2280) with PCIe and
SATA modes
LAN Dual Intel® Lan: 1 x Intel® I210AT (Co-lay I211AT), 1 x Intel®
I225LM (Intel vPro supported)
Audio Realtek ALC897 High Definition Audio CODEC
Rear panel I/O ports
1 x HDMI™ port
3 x DisplayPorts
3 x USB 3.2 Gen 2 ports (2 x Type-A + 1 x Type-C®)
1 x USB 3.2 Gen 1 port
4 x USB 2.0 ports
2 x LAN (RJ45) ports
1 x P/S2 keyboard port
1 x P/S2 mouse port
1 x COM port (RS232/422/485)
2 x Audio jacks
1-3
Chapter 1: General information
Internal I/O ports
4 x COM Port headers (1 x RS232/422/485, 3 x RS232)
1 x USB 3.2 Gen 1 connector supports additional 2 USB 3.2
Gen 1 ports
1 x USB 3.2 Gen 1 stick socket
1 x USB 2.0 header supports additional 2 USB 2.0 ports
1 x CPU Fan header with PWM mode
1 x Chassis Fan header with PWM mode
1 x Disable ME jumper
1 x LVDS/eDP selection connector
1 x Panel SW header
1 x Front Panel Audio header (AAFP)
1 x System Panel header
1 x S/PDIF header
1 x Chassis Intrude header
1 x Speaker header
1 x Clear CMOS header
1 x COM Debug header
1 x AT/ATX mode selection header
1 x 24-pin ATX Power connector
1 x 8-pin ATX Power connector
1 x SPI TPM header
GPIO 1 x 8-bit GPIO header
Manageability WfM 2.0, DMI 2.0, WOL by PME
Watch dog timer Yes
Power requirement ATX mode
12V DC-IN (Supported by an additional cable)
Operation Temperature 0~60°C
Non-Operation
Temperature -40~85°C
Relative Humidity 5%~95%
OS support
Windows® 10 (64-bit)
Windows® IoT Enterprise
Ubuntu
RedHat Enterprise
Fedora Workstation
OpenSUSE
Certification CE, FCC
Form Factor Mini-ITX Form Factor, 6.7”x 6.7” (17.0cm x 17.0cm)
NOTE: Specifications are subject to change without notice. Please refer to the
ASUS website for the latest specifications.
R680EI-IM-A
1-4
2-1
Chapter 2: Motherboard information
Chapter 2
Motherboard information
2.1 Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
CAUTION!
Unplug the power cord from the wall socket before touching any
component.
Before handling components, use a grounded wrist strap or touch a safely
grounded object or a metal object, such as the power supply case, to avoid
damaging them due to static electricity.
Hold components by the edges to avoid touching the ICs on them.
Whenever you uninstall any component, place it on a grounded antistatic
pad or in the bag that came with the component.
Before you install or remove any component, always remove the AC power
by unplugging the power cord from the power outlet. Failure to do so may
cause severe damage to the motherboard, peripherals, or components.
R680EI-IM-A
2-2
R680EI-IM-A
17.0cm(6.7in)
17.0cm(6.7in)
EATXPWR
DDR5 SO-DIMM_B1 (64bit, 260-pin module)
DDR5 SO-DIMM_A1 (64bit, 260-pin module)
M.2(SOCKET3)
M.2(SOCKET3)
PCIE SATA IRST
4.0 X4 V V
COM_DEBUG
COM1_SEL
VCC_PWR_SEL
BKLTEN_SEL
AT_ATX_SEL
CHASSIS
SPDIF_OUT
F_PANEL
SPEAKER
LCD_BLKT_PANEL
COM3
USB_213
COM4 COM5
COM2
SATA6G_3
SATA6G_4
SATA6G_2SATA6G_1
CLRTC
AAFP
BATTERY
AUDIO
Super
I/O
LAN1_U32G1_5
DP_12
LAN1_U32G2_45
U32G2_C1
U32G1_6
COM2_SEL
KBMS
128Mb
BIOS
LGA1700
LVDS_EDP
U32G1_78
Intel®
R680E
Intel®
i210AT
Intel®
I225LM
ALC
897
PCIEX16(G5)
CPU_FAN
CHA_FAN
USB_9~12
DP3
HDMI
COM1
PANEL_SW
GPIO_CON
TPM
M.2(WIFI)
2280 2260 2242
EATX12V
DIS_ME
17
18
15
16
14
4
13
13
19
202122
25
26
27
28
24
23
15
8 9 1 11 121032 76
4
51
2.2 Motherboard layout
Place this side
towards the rear
of the chassis
NOTE: Place four screws into the holes indicated by circles to secure the
motherboard to the chassis.
CAUTION! Do not overtighten the screws! Doing so can damage the
motherboard.
2-3
Chapter 2: Motherboard information
Connectors/Jumpers/Slots Page
1. CPU and Chassis Fan headers (4-pin CPU_FAN, 4-pin CHA_FAN) 2-18
2. Display panel VCC power selection (6-pin VCC_PWR_SEL) 2-10
3. LVDS/eDP Backlight panel connector (5-pin LCD_BLKT_PANEL) 2-22
4. ATX Power connectors (24-pin EATXPWR, 8-pin EATX12V) 2-24
5. Intel® LGA1700 CPU socket 2-4
6. Digital Audio header (4-1 pin SPDIF_OUT) 2-23
7. Chassis Intrude header (4-1 pin CHASSIS) 2-12
8. AT/ATX mode selection (3-pin AT_ATX_SEL) 2-11
9. Serial Port headers (10-1 pin COM2, COM3, COM4, COM5) 2-22
10. General purpose input/output connector (10-pin GPIO_CON) 2-17
11. Speaker header (4-pin SPEAKER) 2-20
12. System Panel header (10-1 pin F_PANEL) 2-19
13. COM1/2 Ring/+5V/+12V selection jumpers (6-pin COM1_SEL, COM2_SEL) 2-10
14. DDR5 SO-DIMM slots 2-9
15. USB 3.2 Gen 1 connectors (20-1 pin U32G1_78)/ (U32G1_6) 2-16
16. USB 2.0 header (10-1 pin USB_213) 2-17
17. SATA 6.0Gb/s ports (7-pin SATA6G_1-4) 2-20
18. Clear CMOS header (2-pin CLRTC) 2-13
19. PCI Express 5.0 x16 slot 2-25
20. Disable ME jumper (3-pin DIS_ME) 2-11
21. Front Panel Audio header (10-1 pin AAFP) 2-23
22. RTC Battery header (2-pin BATTERY) 2-21
23. M.2 Wi-Fi 2-21
24. M.2 socket 3 2-21
25. SPI TPM header (14-1 pin TPM) 2-18
26. LCD Panel Monitor Switch header (2-pin PANEL_SW) 2-16
27. LVDS/eDP Signal connector (LVDS_ePD) 2-20
28. LVDS/eDP Panel Enable Signal Selection header (3-pin BKLTEN_SEL) 2-12
R680EI-IM-A
2-4
IMPORTANT! Unplug all power cables before installing the CPU.
CAUTION!
Upon purchase of the motherboard, ensure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the
PnP cap/socket contacts/motherboard components. The manufacturer will
shoulder the cost of repair only if the damage is shipment/transit-related.
Keep the cap after installing the motherboard. The manufacturer will
process Return Merchandise Authorization (RMA) requests only if the
motherboard comes with the cap on the LGA1200 socket.
The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
2.3 Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA1700 socket designed for the
Intel® 12th Generation Intel® Core™ i9 / Core™ i7 / Core™ i5 / Core™ i3, Pentium®,
and Celeron® processors.
R680EI-IM-A
LGA1700
2-5
Chapter 2: Motherboard information
2.3.1 CPU installation
1
2 3
R680EI-IM-A
2-6
4
5
2-7
Chapter 2: Motherboard information
2.3.2 CPU heatsink and fan assembly installation
CAUTION! Apply the Thermal
Interface Material to the CPU
heatsink and CPU before you
install the heatsink and fan if
necessary.
To install the CPU heatsink and fan assembly
B
A
A
B
LGA1200
LGA1700
LGA1800
12
3 4
R680EI-IM-A
2-8
A
B
B
A
To uninstall the CPU heatsink and fan assembly
2
1
2-9
Chapter 2: Motherboard information
2.4 System memory
This motherboard comes with two Double Data Rate 5 (DDR5) Small Outline Dual Inline
Memory Module (SO-DIMM) sockets. The figure below illustrates the location of the DDR5
SO-DIMM sockets:
Channel Sockets
Channel A SO-DIMM_A1
Channel B SO-DIMM_B1
Installing a DIMM
SO-DIMM_A1
SO-DIMM_B1
R680EI-IM-A
1 2
To remove a DIMM
B
A
B
A
A
DIMM_B1
DIMM_A1
DIMM_A1
DIMM_B1
Recommended memory configuration
R680EI-IM-A
2-10
2.5 Jumpers
Setting Pins
3V (Default) 1-2
5V 3-4
12V 5-6
1. Display panel VCC power selection (6-pin VCC_PWR_SEL)
R680EI-IM-A
3
12V
2
5V
1
3V
(Default)
VCC_PWR_SEL
Connector type
HEADER 2 x 3p, 2.54mm pitch, S/T
2. COM1/2 Ring/+5V/+12V selection (6-pin COM1_SEL, COM2_SEL)
Setting Pins
+12V 1-2
+5V 3-4
Ring (Default) 5-6
R680EI-IM-A
RI
(Default)
+5V+12V
COM1_SEL
COM2_SEL
12 34 56
RI
(Default)
+5V+12V
1
2
3
4
5
6
B
A
A
B
Connector type
HEADER 2x3p, 2.54mm pitch, S/T
2-11
Chapter 2: Motherboard information
3. AT/ATX mode selection (3-pin AT_ATX_SEL)
Pins
1-2 (Default) ATX mode
2-3 AT mode
R680EI-IM-A
21 2 3
ATX mode
(Default)
AT mode
AT_ATX_SEL
Connector type
HEADER 1x3p, 2.54mm pitch, S/T
4. Disable ME jumper (3-pin DIS_ME)
This jumper allows you to enable or disable the Intel® ME function. Set this
jumper to pins 1-2 to enable (default) the Intel® ME function and to pins 2-3 to
disable it.
R680EI-IM-A
21 2 3
DIS_ME
Disable intel
ME function
Normal
(Default)
Connector type
HEADER 1x3p, 2.54mm pitch, S/T
R680EI-IM-A
2-12
5. Chassis Intrude header (4-1 pin CHASSIS)
This header is for a chassis-mounted intrusion detection sensor or switch.
Connect one end of the chassis intrusion sensor or switch cable to this
connector. The chassis intrusion sensor or switch sends a high-level signal to
this connector when a chassis component is removed or replaced. The signal
is then generated as a chassis intrusion event.
By default, the pin labeled “Chassis Signal” and “Ground” are shorted with
jumper caps. Remove the jumper caps only when you intend to use the
chassis intrusion detection feature.
R680EI-IM-A
PIN 1
+5VSB_MB
Chassis Signal
GND
CHASSIS
Connector type
HEADER 4p, K2, 2.54mm pitch
6. LVDS/eDP Panel Enable Signal Selection header (BKLTEN_SEL)
Pins
1-2 (Default) High Active
2-3 Low Active
R680EI-IM-A
1 2 2 3
High Active
(Default)
Low Active
BKLTEN_SEL
Connector type
HEADER 1x3p, 2.54mm pitch, S/T
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Asus R680EI-IM-A User manual

Category
Motherboards
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages