Lefroy Brooks CR 1290 Installation & Servicing Guide

CR 1290
Lefroy Brooks
Brand
Lefroy Brooks
Model
CR 1290
Type
Installation & Servicing Guide
1210 / 1258 / 2200 / 2210 / 4125 / 4135
WALL MOUNTED BASIN & BATH SPOUTS
INSTALLATION GUIDE
2
IMPORTANT INFORMATION
Professional installation
We recommend that our products are fitted by
a fully qualified professional plumber. They should
be installed correctly and in accordance with all
local water regulations and the system protected
by non-return valves (not supplied). All products
should be accessible for routine servicing.
Suits all systems
This Lefroy Brooks product is potentially suitable
for every possible application, type of boiler and
water supply pressure. However, if your supply
pressure is below 1 bar it is advisable to fit a water
pump. For systems with combination boilers,
it is not advisable to fit pumps (refer to boiler
manufacturer).
Supply temperature safety notice
A thermostatic mixing valve (TMV) should be
fitted (not supplied) to the hot supply to restrict
the temperature to a safe working/maximum
temperature to comply with local building
regulations, current legislation, relevant standards
and codes of practice. Maximum allowed
temperatures vary subject to type of installation or
specification of building.
Flushing system
It is most important to flush out all pipework
thoroughly before connecting the product. Failure
to do so may block aerators and reduce or prevent
water flow.
Supply connections
Lefroy Brooks do not supply any pipework or
connections for the spouts. The threaded spout
tails can be cut to length to suit the available
cavity and connected to the water supplies using a
standard tee connection.
Balancing flow
When using wall valves as separate hot and cold
supplies, if a significant dierence in pressure
exists, we advise fitting a ‘flow regulator’ (not
supplied) to the higher or both supplies.
Servicing
Suitable access should be available to aid any
future maintenance/servicing. Installing isolation
valves will make servicing much easier (not
supplied).
All serviceable parts are available to maintain
your Lefroy Brooks product (contact retailer for
details).
Water quality
In hard water areas a suitable water treatment
system should be provided to prevent limescale
deposits (calcium deposits). Exterior surfaces
should be gently wiped with a dry soft cloth
after use to minimise water stains and limescale
deposits.
66mm
190mm
G½ (Ø21mm)
Ø19mm
XO 4135 & TT 1210 – Zu basin wall spout
Ø32mm
Ø50mm
65mm
Ø56mm
176mm
LB 2200 – Classic basin wall spout
G½ (Ø21mm)
50mm
max
80mm
191mm
G½ (Ø21mm)
FR 2200 – La Chapelle basin wall spout
Ø70mm
45mm
max
70mm
170mm
JM 2200 – Janey Mac basin wall spout
3mm
Ø25mm
G½ (Ø21mm)
50mm
max
73mm
Ø50mm
50mm
MK 2200 – Mackintosh basin wall spout
60mm A/F
165mm
G½ (Ø21mm)
50mm
max
75mm
Not to scale
3
BASIN SPOUT DIMENSIONS
Not to scale
215mm75mm
77mm A/F
G¾ (Ø26mm)
MK 2210 – Mackintosh bath wall spout
50mm
max
45mm
max
70mm
Ø64mm
170mm
LBE 2210 – Classic bath wall spout
G½ (Ø21mm)
Ø64mm
45mm
max
73mm 170mm
LB 2210 – Classic bath wall spout
G¾ (Ø26mm)
45mm
max
70mm
G½ (Ø21mm)
Ø79mm
225mm
FRE 2210 – La Chapelle bath wall spout
Ø79mm
225mm
G¾ (Ø26mm)
45mm
max
70mm
FR 2210 – La Chapelle bath wall spout
4 5
BATH SPOUT DIMENSIONS
Not to scale
215mm
Ø25mm
66mm
Ø55mm
Ø38mm
69mm
XO 4125 & TT 1258 – Zu bath wall spout
G½ (Ø21mm)
190mm
225mm
RTE 2210 – Belle Aire bath wall spout
3mm
Ø25mm
G½ (Ø21mm)
50mm
max
73mm
190mm
225mm
39mm max
63mm
G¾ (Ø26mm)
RT 2210 – Belle Aire bath wall spout
Ø80mm
216mm
JME 2210 – Janey Mac bath wall spout
3mm
Ø25mm
G½ (Ø21mm)
50mm
max
73mm
Ø80mm
216mm
45mm
max
73mm
JM 2210 – Janey Mac bath wall spout
G¾ (Ø26mm)
5
BATH SPOUT DIMENSIONS
10 20 30 40
3.0
2.0
1.0
50
Flow (Litres/minute)
Static Pressure (Bar)
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
10 20 30 40
3.0
2.0
1.0
50
Flow (Litres/minute)
Static Pressure (Bar)
6
FR 2220 basin wall spout
TYPICAL FLOW RATES
LB 2220 & JM 2200 basin wall spouts
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
TYPICAL FLOW RATES
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
5.0 10.0 15.0 20.0
3.0
2.0
1.0
25.0
Flow (Litres/minute)
Static Pressure (Bar)
5.0 10.0 15.0 20.0
3.0
2.0
1.0
25.0
Flow (Litres/minute)
Static Pressure (Bar)
7
MK 2200 basin wall spout
XO 4135 & TT 1210 basin wall spout
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
TYPICAL FLOW RATES
10 20 30 40
3.0
2.0
1.0
50
Flow (Litres/minute)
Static Pressure (Bar)
10 20 30 40
3.0
2.0
1.0
50
Flow (Litres/minute)
Static Pressure (Bar)
8
LB 2210, LBE 2210, MK 2210, TT 1258 & XO 4125 bath wall spouts
FR 2210 & FRE 2210 bath wall spouts
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
10 20 30 40
3.0
2.0
1.0
50
Flow (Litres/minute)
Static Pressure (Bar)
TYPICAL FLOW RATES
510 15 20
3.0
2.0
1.0
25
Flow (Litres/minute)
Static Pressure (Bar)
Note: Balanced pressures shown are applied directly to the hot and cold inlets; flow rates indicated are free
flowing and may vary subject to restrictions created by installation, pipework, layout or application.
9
RT 2210 & RTE 2210 bath wall spouts
JM 2210 & JME 2210 bath wall spouts
Mounting
surface
Spout
Washer
Backnut
Mounting surface
Spout
Washer
Backnut
Tee connector
CavityWall
10
1 Drill a suitable sized hole through the
mounting surface.
2 Insert the spout tail through the opening in the
mounting surface.
3 Locate the washer on to the spout tail.
4 Screw the backnut on to the spout tail.
(All models except TT 1210, TT 1258, XO 4125 & XO 4135)
INSTALLATION
Spouts are not suitable for solid walls.
A
B
C
D
E
11
TT 1210, TT 1258, XO 4125 & XO 4135 only
1 Unscrew and remove the grub screw from the
base of the spout using the supplied 2.5mm
hexagonal key (A).
2 Pull the wall adapter clear of the spout body
(B).
3 Apply suitable sealing compound/tape to the
thread of the wall adapter and screw into a
suitable female wall fitting (C).
4 Gently push the spout onto the wall adapter
(D) then fit the grub screw to secure (E).
INSTALLATION
Aerator/flow straightener
Washer
Cover
12
SERVICING – CLEANING THE AERATOR/FLOW STRAIGHTENER
1 There is an aerator/flow straightener located
in the end of the spout. To remove this
unscrew and remove the cover.
2 The aerator/flow straightener can be cleaned
in warm soapy water.
3 Assemble in the reverse order.
Shown with Janey Mac bath spout.
The same procedure applies to all models fitted with aerators/flow straighteners.
Not applicable to Classic bath spout (LB 2210).
T YPIC AL L AYOUT
There are no regulations specifying the position between spout and valves.
They can be installed as required.
13
REPLACEMENT AERATORS/FLOW STRAIGHTENERS
Belle Aire Bath – PSH032
Classic Basin – PSH030
Classic Bath – None fitted
La Chapelle Basin – PSH034
La Chapelle Bath – PSH035
Janey Mac Basin – PSH108
Janey Mac Bath – PSH127
Mackintosh Basin – PSH029
Mackintosh Bath – PSH032
XO & TT Basin – PXT029
XO & TT Bath – PXT030
Whilst every effort is made to ensure the accuracy of these, they are subject to change without
notice as part of the company’s product development process. The use of trademarks, product design
and artwork is subject to licence or agreement with LBIP Ltd. The design registrations, trademark registrations
and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited.
The right to modify designs and dimensions is reserved. LBIP Ltd is a member of ACID (Anti Copying in Design). E&OE
© LBIP Ltd 2022
CONTRACT ENQUIRIES
+44 (0)1992 708 316
info@lefroybrooks.co.uk
CUSTOMER SERVICE, SPARES & TECHNICAL ENQUIRIES
+44 (0)1902 390 894
technical@lefroybrooks.co.uk
LEFROYBROOKS.CO.UK
20.065.309B / FEBRUARY 2022
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Lefroy Brooks CR 1290 Installation & Servicing Guide

CR 1290
Lefroy Brooks
Brand
Lefroy Brooks
Model
CR 1290
Type
Installation & Servicing Guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents