2. Dynisco
  3. LCR7000

Dynisco LCR7000 Operating instructions

  • Hello! I've reviewed the Dynisco Installation Guide for the Rheometer LCR7000 Edge_Serial and Dynisco Edge_Serial Cloud Connect Device. This document outlines the steps for setting up your device. I can answer questions about connecting the device, power supply, network connections, cloud setup, and initial software configurations. I'm ready to assist you with any questions you have.
  • How do I connect the device to the instrument?
    What do I do if the communication port dialog box does not appear?
    How do I send data to the cloud?
    How can I check if the data has been sent to cloud?
-1-
38 Forge Parkway | Franklin, MA 02038 USA | Tel: +1 (508) 541-9400 | Fax: +1 (508) 541-6206
www.dynisco.com
From lab to production,
providing a window into the process
Dynisco Edge_Serial_R
LMI7000 Installation Guide with RheoSightsTM Application Software
LCR7000 Capillary Rheometer with
Dynisco Edge_Serial Cloud Connect Device
& RheoSightsTM Application Software
Step 2: Remove USB to Serial Cable & Edge Device
Step 1: Open Box
Step 3: Remove & Open White Power Supply Box
Step 4: Select Appropriate Power Supply Connection
Step 6: Slide Out Power Connector
and Slide in New Connecter
-2-
38 Forge Parkway | Franklin, MA 02038 USA | Tel: +1 (508) 541-9400 | Fax: +1 (508) 541-6206
www.dynisco.com
From lab to production,
providing a window into the process
Step 7: Locate Power Connection on
Dynisco Edge Device
Step 9: Insert USB Cable into the USB2.0 Slot on
the Dynisco Edge Device Shown Above
Step 10: Insert Ethernet Cable (Customer Supplied) into
the Dynisco Edge Device
Step 11: Insert HDMI Cable for Computer Monitor (Both
Customer Supplied) into the Dynisco Edge Device
Shown Above
Step 12: Insert USB Cable (Keyboard/Mouse)
Into Dynisco Edge Device
Step 13: Plug Power Supply into Wall
(Do Not Plug Dynisco Edge Device into Instrument at this Time)
Step 14: Click OK on Prompt
(Do Not Plug Dynisco Edge Device Into Instrument at this Time)
-3-
38 Forge Parkway | Franklin, MA 02038 USA | Tel: +1 (508) 541-9400 | Fax: +1 (508) 541-6206
www.dynisco.com
From lab to production,
providing a window into the process
Important Notes- if you plan to swap the Dynisco Cloud Connect Edge Devices between Instruments
• Separate Cloud Connect software keys will need to be supplied by Dynisco with instructions on how to
swap from one LCR7000 to another unit.
• You can scale RheoSightsTM view screen by clicking on your keyboard
Step 15: When you See this Prompt, Connect the Serial end of the USB Cable into the Instrument and Click OK
Note: If the connect the communication port dialog box does not appear in 3 min, click the “Edge” icon to initiate the script
Step 16: Successful connection will occur when the above dialog box appears
Notes:
• Dynisco suggests you change your password upon login and make sure it is recorded
• You will then need to click on the IoT Dynisco Icon “shown above” to setup your Dynisco Cloud Connect
account. You will find instructions on how to register and use the Dynisco Cloud Connect Dashboard on
iot.dynisco.com
• Upon successful registration and account setup, your LMI will send data to the cloud using the “print”
feature on the device.
• You can tell if data has been sent by the “Last Sent” line on the Dynisco Edge Device Running screen
(see above)
• Yearly subscription prices can be supplied by contacting your regional sales manager with contact info
on www.dynisco.com
• Please Remember to Log off Windows on the Edge Device as if you would with any other Microsoft
Computer. Do Not Disconnect Power without Shutting down the Operating System
• You may need to set the local time zone as you would with any Microsoft Windows Computer on your
network.
/