Danfoss Link™ HR Hidden Relay Operating instructions

MAKING MODERN LIVING POSSIBLE

Danfoss Heating Solutions

Danfoss Link™ HR Hidden Relay

Installation Guide

2

VISGX45X © Danfoss 04/2011

Installation Guide Danfoss Link™ HR

3

VISGX45X © Danfoss 04/2011

Installation Guide Danfoss Link™ HR

Installation Guide

Installationsanleitung

Guide d’installation

Installationsmanual

Installationshandbok

Asennusohje

Installatiehandleiding

Instrukcja instalacji

Instalační příručka

GB

DE

FR

DK

SE

FI

NL

PL

CZ

4

VISGX45X © Danfoss 04/2011

Introduction ............................................... 5

Installation................................................. 6

Adding device ............................................. 7

Perform network test....................................... 8

Factory reset ............................................... 8

Trouble shooting........................................... 8

Technical specications .................................... 9

Disposal instructions ....................................... 9

Index

Installation Guide Danfoss Link™ HR

5

VISGX45X © Danfoss 04/2011

The Danfoss Link™ HR (Hidden Relay) is a device for switch-

ing heating elements or other electrical equipments ON/

OFF, either manually or by schedule.

LED

Install

buttons

Fuse

(including

spare fuse)

The Danfoss Link™ HR is powered by 230 V~ and shall

according to regulations be installed in a build in box or in

the wall box.

Introduction

GB

Installation Guide Danfoss Link™ HR

6

VISGX45X © Danfoss 04/2011

Note! Do not install electric oor heating system without a oor

sensor, when the heating element is installed on or beneath

wooden surfaces and other surfaces sensitive to temperature!

Installation

The Danfoss Link™ wireless system’s transmission range is

sucient for most applications; however each building has

dierent obstacles aecting communication and maximum

transmission distance.

If communication problems occur Danfoss suggests that

accessories would be required to support the system, such as

repeaters. In exceptional cases the wireless system may not be

suitable for your installation.

Please be aware of the following, when installing Danfoss

Link™ HR:

Installation and placement must be according to

local building regulations.

Operation mode

Danfoss Link™ HR supports two types of operation modes:

1. ON/OFF switching.

2. Heating regulation: when using Danfoss Link™ HR as heat-

ing regulation in a room you also have to install a Danfoss

Link™ RS.

Installation Guide Danfoss Link™ HR

7

VISGX45X © Danfoss 04/2011

Installation

1. Danfoss Link™ HR is to be mounted

into a build in box in the wall.

2. It is recommended not to install

the HR in a metal box due to the

possible disturbance of the radio

communication.

3. Connect the Danfoss Link™ HR ac-

cording to the connection diagram.

Installation Guide Danfoss Link™ HR

L

N

GB

Adding Danfoss Link™ HR to a system is

made from the Danfoss Link™ CC Central

Controller.

When adding, press the install but-

ton until the LED gives a fast

green ash.

For further information,

see the Danfoss Link™ CC

instruction manual:

Conguration 6:

Adding devices.

Adding device

Max. 1 m

8

VISGX45X © Danfoss 04/2011

Installation Guide Danfoss Link™ HR

When the Danfoss Link™ HR has

been added to the Danfoss Link™

CC Central Controller, a network test

should be performed.

For more information on network

tests, see the Danfoss Link™ CC

instruction manual:

Conguration 8:

Perform network test.

Perform network test

Green LED ON Relay OFF/Standby

Red LED ON Relay ON/Heating

Green LED fast ash Inclusion or link test

Red LED short ash Inclusion not OK

Link test not OK

Note: If the fuse has burned you can replace it with the spare

fuse, located in the fuse holder.

Trouble shooting

1. Hold both install buttons in front

of the device for approx. 5 sec. until

LED gives a red ash.

Factory reset

9

VISGX45X © Danfoss 04/2011

Installation Guide Danfoss Link™ HR

GB

Technical specications

Operation voltage 230 V AC, 50 Hz

Standby consumption <1W

Load

2300 W, 460 VA, 600 W

Incandescent Bulbs

Regulation PWM or ON/OFF

Ambient temperature 0˚ to +35˚C

Micro-fuse T 10 A H

Transmission

frequency

868.42 MHz

Transmission range in

normal buildings

Up to 30 m

Transmission power Max. 1 mW

IP class 20

Dimensions 52 mm × 52 mm × 31 mm

Disposal instructions

Page is loading ...

45

Installatiehandleiding Danfoss Link™ HR

Technische specicaties

Bedrijfsspanning 230 V AC, 50 Hz

Stand-byverbruik < 1 W

Belasting

2300 W, 460 VA, 600 W

gloeilampen

Regeling PPM of AAN/UIT

Omgevingstemperatuur 0 tot +35 °C

Microzekering T 10 A H

Transmissiefrequentie 868,42 MHz

Transmissiebereik in

normale gebouwen

Tot 30 m

Transmissievermogen Max. 1 mW

IP-klasse 20

Afmetingen 52 mm × 52 mm × 31 mm

Instructies voor afvoer

NL

Page is loading ...

Danfoss A/S

Heating Solutions

Haarupvaenget 11

8600 Silkeborg

Denmark

Phone: +45 7488 8000

Fax: +45 7488 8100

Email: heating.solutions@danfoss.com

www.heating.danfoss.com

Danfoss Link™ HR Hidden Relay Operating instructions

Danfoss Link™ HR Hidden Relay Operating instructions

in other languages

Related papers

Other documents