Bosch Free-standing dishwasher 60 cm white User manual
- Category
- Dishwashers
- Type
- User manual
en
Index
Safety instructions 4 . . . . . . . . . . . . .
Getting to know your appliance 6 . .
Water softener 7 . . . . . . . . . . . . . . . .
Filling the salt dispenser 8 . . . . . . . .
Adding rinse aid 9 . . . . . . . . . . . . . . .
Utensils 10 . . . . . . . . . . . . . . . . . . . . . .
Detergent 13 . . . . . . . . . . . . . . . . . . . .
auto 3in1 14 . . . . . . . . . . . . . . . . . . . . .
Programme overview 16 . . . . . . . . . .
Washing dishes 17 . . . . . . . . . . . . . . .
Additional functions * 19 . . . . . . . . . . .
Maintenance and care 20 . . . . . . . . . .
Fault finding 22 . . . . . . . . . . . . . . . . . .
Customer Service 25 . . . . . . . . . . . . .
Information 26 . . . . . . . . . . . . . . . . . . .
Installation 26 . . . . . . . . . . . . . . . . . . . .
Waste disposal 28 . . . . . . . . . . . . . . . .
en
4
Safety instructions
Delivery
Immediately check the packaging and
dishwasher for any damage which may
have been caused in transit. Do not use
a damaged appliance, but consult your
supplier.
Please dispose of packaging material
properly.
Installation
Install and connect the appliance
according to the installation and
assembly instructions.
The dishwasher must NOT be
connected to the power supply during
installation.
Ensure that the protective conductor
system of the domestic electricity
supply has been installed correctly.
Electrical connection conditions must
correspond with the specifications on
the rating plate of the dishwasher.
If the dishwasher is to be installed
in a high-sided unit, ensure that the unit
is attached properly and also at the
rear.
Built-under and built-in appliances
should always be installed under a
continuous work surface which is
attached to the adjacent cupboards, in
order to ensure that the appliance is
entirely stable.
After the appliance has been installed,
the mains plug should still be easily
accessible.
Not on all models:
The plastic housing on the water input
contains an electrically operated valve.
The connecting wires are inside the
inlet hose. Do not cut through this hose
and do not immerse the plastic housing
in water.
Warning
For safety reasons, if the appliance is not
fitted in a recess, thereby making a side
wall accessible, the door hinge area
should be covered at the side.
(Risk of injury)
Covers are available as optional
accessories from customer services or
specialist stores.
In daily use
Warning
Knives and other sharp-pointed utensils
must be placed with the points down
in the cutlery basket or horizontally in
the utensils basket.
Use the dishwasher only in the
household and only for its designed
purpose, i.e. for washing domestic
dishes.
Do not lean or sit on the open door.
The appliance could tip.
Please note that free-standing
appliances may tip over if the baskets
are overloaded.
The water in the appliance is not
drinking water.
Do not add any solvents to the washing
chamber. Danger of explosion!
Open the door carefully when
the programme is still running. There
is a risk of hot water spraying out of
the appliance.
To prevent injuries, e.g. caused
by stumbling, open the dishwasher
only briefly in order to load and unload
the dishwasher.
Read and observe the safety
nformation and instructions for use on
the packaging for cleaning and rinsing
agents.
en
5
Children in the household
If fitted, use the childproof lock. An
exact description can be found in the
back of the envelope.
Do not allow children to play with
or operate the appliance.
Keep children away from detergents
and rinse aid. These may cause
chemical burns in the mouth, throat and
eyes or asphyxiation.
Keep children away from an open
dishwasher. There could still be
detergent residue inside.
If the appliance is installed at eye-level,
ensure when opening and closing the
door that children are not caught
or crushed between the appliance door
and the cupboard door situated below.
Damage
The appliance may be repaired and
opened up by a technician only. First
disconnect the appliance from the
power supply. Pull out the mains plug
(do not tug the power cord!) or switch
off the fuse. Turn off the tap.
Disposal
Make redundant appliances unusable
to prevent subsequent accidents.
Dispose of the appliance in an
environmentally friendly manner.
Warning
Children could get locked in the appliance
(risk of suffocation) or get stuck in other
positions.
Therefore: Remove the mains plug, cut the
mains wire and set aside. Damage the
door lock so that the door can no longer
be closed.
Before using for the first time
The appliance was checked before it left
the works. In order to remove possible
water test remains, use the appliance for
the first time without any dishes, using
the highest temperature. Also fill salt, rinse
aid and detergent in the filling
compartments.
en
6
Getting to know your
appliance
Diagrams of the control panel and the
interior of the appliance can be found
in the envelope at the front.
Individual positions are referred to in
the text.
Control panel
1
Main switch
2
Door Opener
3
Programme selector (retractable*)
4
Additional options*
5 “Check water supply” display
6
Salt refill indicator
7
Rinse-aid refill indicator
8 Digital display
* some models
Appliance interior
20
Top basket
21
Additional cutlery basket for the top
basket *
22
Top spray arm
23
Additional cup rack *
24
Bottom spray arm
25
Float **
26
Bottom basket
27
Salt dispenser
28
Filters
29
Cutlery basket
30
Dispenser for rinse aid
31
Detergent dispenser
32
Catch
33
Rating plate
* some models
** The float ensures that the appliance
interior is not overfilled. Only customer
service may maintain, remove and install
the float.
You will need to purchase the
following before using the
dishwasher for the first time:
– special salt for use in dishwashers
– detergent
– rinse-aid
Only use products, which are suitable for
dishwashers.
en
7
Water softener
In order to rinse dishes and glasses
satisfactorily, the dishwasher requires soft
water, i.e. containing little or no lime,
otherwise water stains will be left behind
on crockery and glasses, etc.
If the tap water exceeds a certain level of
hardness, it must be softened, i.e.
decalcified, so that it can be used in the
dishwasher.
This is achieved by adding a special salt
to the water softener inside the
dishwasher.
The water softener, that is the required
amount of salt, is set up according to how
hard the tap water is.
Setting up the water softener
Determine the level of hardness of your
tap water. Your local water company or
service agent can help you with this.
Identify setting from the following water
hardness table.
Water hardness table
Close the door
Rotate the programme selector
3
from the 12 o’clock position by one
notch to the left.
Switch on main switch
1
and hold
down for at least 3 sec.
The digital display
8
indicates the
current set hardness value and the salt
refill indicator
6
flashes
(hardness value has been set to 4
at the factory).
To change the setting: Rotate the
programme selector
3
.
You can select a set value between
0 and 7 according to the hardness
of your water.
Switch off the main switch
1
.
The chosen setting has now been
stored.
Approx. 4 litres of water are required for
regenerating the water softening system.
The overall water consumption per load
can therefore be increased by between 0
and a maximum of 4 litres according to the
water hardness setting.
en
8
Filling the salt dispenser
Salt must always be filled before the
appliance is switched on, so that excess
salt solution is immediately flushed away
to prevent corrosion.
Open the screw-type cap of the
compartment
27 .
Before using the appliance for the first
time, pour about 1 litre of water in the
salt container.
Then refill with salt (not cooking salt)
until the salt container is full
(max. 1.5 kg). When you refill the salt,
water is being displaced and drains off.
The LOW SALT indicator
6
on the front
panel will light up initially but will extinguish
again after a short period when the salt
solution has become sufficiently
concentrated.
If the set hardness value is , do not add
salt because no salt is used during
operation; the salt refill indicator
is switched off.
Warning
Do not pour detergent into the container
for special salt. This would destroy the
water softener.
Salt refill indicator
As soon as the salt refill indicator
6
is lit
on the control panel, refill with salt
immediately before the next rinse cycle.
Depending on the washing frequency and
the hardness setting, the regeneration salt
may not have to be topped up for several
months.
en
9
Adding rinse aid
The rinse aid is required for stain-free
utensils and clear glasses.
Use only rinse aid for domestic
dishwashers.
Open the cover on the rinse-aid
dispenser
30 . To do this, press the
mark (1
) on the cover and
simultaneously lift the cover on the
control plate (2
).
Carefully pour in the rinse aid to just
below the edge of the filler opening.
Close the lid, ensuring that you hear it
snap closed.
To prevent excessive foam formation
during the next rinse cycle, remove any
rinse aid which has run over with a cloth.
Adjusting the amount of
rinse-aid
The amount of rinse-aid added to the
water can be varied by adjusting the
stepless control. The rinse-aid control has
been set to ”4” in the factory.
Do not alter the setting of the rinse-aid
control unless streaks (turn knob towards
”–”) or water marks (turn knob towards ”+”)
are left on the dishes.
30
Rinse aid controller
Rinse-aid refill indicator
As soon as the rinse-aid refill indicator
lights up on the control panel
7
,
refill with rinse aid.
If using detergent products with integrated
rinse aid, the rinse-aid refill indicator
can be switched off (see “Switching
the rinse-aid refill indicator off and on”
in the “auto 3in1” chapter).
en
10
Utensils
Not suitable
Cutlery and utensils made of wood.
Fragile decorative glasses,
hand-crafted and antique utensils.
These decorative items are not
dishwasher-proof.
Plastic parts sensitive to hot water.
Copper and tin utensils.
Utensils which are soiled with ash,
wax, lubricating grease or ink.
Absorbent materials such as sponges
and cloths.
Aluminium and silver parts have a
tendency to discolour and fade during the
wash cycle. Even some types of glass
(e.g. crystal glass objects) may turn cloudy
after many wash cycles.
Recommendation:
In future buy utensils which are identified
as dishwasher-proof.
Damage to glassware and other
dishes
Possible causes:
type of glass or manufacturing process
chemical composition of detergent
water temperature and duration of
dishwasher programme.
Suggested remedy:
Use glassware or porcelain dishes that
have been marked ’dishwasher–proof’
by the manufacturer.
Use a mild detergent that is described
as ’kind to dishes’. If necessary, seek
further information from detergent
manufacturers.
Select a programme with as low a
temperature and as short a duration as
possible.
To prevent damage, take glass and
cutlery out of the dishwasher as soon
as possible after the programme has
ended.
Loading the dishwasher
It is not necessary to rinse them off
under running water.
When loading the dishwasher, ensure
that
D
all utensils are secure and cannot
fall over.
D
the openings of all receptacles are
face down.
D
curved or indented utensils are at
an incline, allowing water to drain.
D
the two spray arms can rotate freely.
Very small items should not be washed in
the dishwasher as they could easily fall out
of the baskets.
Removing the dishes
To prevent water dripping from the top
basket onto the dishes in the lower basket,
we recommend that you empty the lower
basket first and then the top basket.
Cups and glasses
Upper basket
20
* on applicable models
en
11
Pots and pans
Lower basket
26
Cutlery
Cutlery should be placed in the
dishwasher always unsorted and with the
eating surface pointing downwards. The
spray jet is then better able to reach the
individual parts.
To prevent injuries, place long, pointed
accessories and knives on the étagère
(some models) or on the knife shelf
(available as an accessory).
Folding spikes *
* on applicable models
To improve stacking of pots and pans, the
spikes can be folded down.
Shelf *
* not on all models
Lean tall glasses and those with long
stems against the shelf – not against other
items to be washed.
Long items, serving cutlery, salad servers
or knives should be placed on the shelf so
that they do not obstruct the rotation of the
spray arms. The shelf can be folded back
when not required for use.
Small accessories holder*
* some models
Light-weight plastic accessories, e.g. cups,
lids, etc. can be held securely in the small
accessories holder.
en
12
Adjusting the height
of the basket *
* some models
If required, the height of the upper utensils
basket can be adjusted to provide more
space for tall utensils either in the upper
or lower basket.
Appliance height in cm
81 86
Max. ø in cm upper 20/25* 20/25*
max. ø in cm lower 30/25* 34/29*
Select one of the two following procedures
according to the design of the top basket
for your appliance model:
Top basket with upper and
lower roller pairs
Pull out the top basket.
Remove the top basket and re-attach
it to the upper or lower rollers.
Top basket with side levers
(Rackmatic)
Pull out the top basket.
To lower the basket, press in one lever
and then the other situated on the left
and right of the basket exterior, holding
the basket firmly on the sides of the
upper edge to prevent it from falling
down.
To raise the basket, hold the basket on
the sides of the upper edge and lift it
up.
Before re-inserting the basket again,
ensure that it is at the same height
on both sides. Otherwise, the appliance
door cannot be closed and the upper
spray arm will not be connected to
the water circuit.
en
13
Detergent
You can use commercially available liquid
or powder proprietary detergents for
dishwashers or TABS (do not use
handwash!).
If phosphate-free detergents are used with
hard tap water, white deposits may be
deposited more easily on utensils and
the container walls. This can be remedied
by adding more detergent.
See detergent packaging to determine
whether a detergent is suitable for silver
parts.
If you have any other questions, we
recommend that you contact the helplines
of the detergent manufacturers.
Detergent dispenser with
dosing aid
The graduated detergent dispenser helps
you pour in the correct amount.
Lower line: 15 ml
Middle line: 25 ml
Full to the brim: 40 ml
If the detergent dispenser 31 is still
closed, press the lock
32 to open the
detergent dispenser.
Adding detergent
Fill the dispenser 31 with detergent.
Dosage: see manufacturer’s
instructions on the detergent
packaging.
Important
Due to the different solvency properties of
the detergent tablets supplied by various
manufacturers, the cleaning efficiency of
the detergent may not be fully utilised by
short programmes. It is recommended to
use washing powder for these
programmes.
The Intensive programme (on some
models) requires one tab only. When using
washing powder, you can apply some
of this cleaning agent to the inside of
the appliance’s door.
Reduce costs!
If your dishes are only moderately dirty,
you may be able to use less detergent
than recommended.
Close the lid on the detergent
compartment.
Press down the lid (1) until it clicks
shut (2).
If you are using detergent in tablet form,
read the manufacturer’s
recommendations on the packaging in
order to
determine where the tablets should be
placed inside the dishwasher (e.g. in
cutlery basket, detergent compartment,
etc.).
Make sure that the lid on the detergent
compartment is closed, even if you are
using tablets.
en
14
auto 3in1
The use of so-called combined detergent
products may make the use of rinse aid
and/or salt unnecessary.
There are currently several types of
combined detergent products available.
3in1: They contain detergent, rinse aid
and salt function.
2in1: They contain detergent and rinse
aid or salt function.
>>> Always check the type of detergent
or combined product which you
are using!
Always follow the operating instructions
or the information on the packaging.
The rinse programme is automatically
adjusted in order to obtain the best
possible rinsing and drying result.
Observe the following important
information if using combined cleaning
products:
Regeneration salt is not required up to
a water hardness of 21_ dH (37_ fH,
26_ Clarke, 3.7 mmol/l) only. No other
settings on the appliance are required.
Salt is still required if the water
hardness is above 21_ dH (37_ fH,
26_Clarke, 3.7 mmol/l). Fill the salt
dispenser with salt
27
and select
setting 6 on the water softening system.
If in doubt, please contact the detergent
manufacturer, especially if:
the utensils are very wet at the end
of the programme.
limescale forms.
Note
Optimum rinsing and drying results can be
obtained by using standard detergents in
conjunction with separate application of
salt and rinse aid.
Observance of the operating instructions
or information on the packaging of the
combined detergents determines their
effectiveness.
Note
Even if the rinse aid and/or salt refill
indicator is lit, the rinse programme runs
correctly when 3in1 products are used.
If the rinse aid refill indicator
7
or salt
refill
6
indicator is defective and you
would like to switch it off, proceed as
follows:
Switching the rinse-aid refill
indicator off or on*
* some models
You can switch off the rinse-aid refill
indicator
7
if you use a detergent
with integrated rinse-aid.
Close the door.
Press and hold down button A .
Press main switch
1
until the digital
display lights up.
Release both buttons.
The digital display
8
indicates
(rinse-aid refill indicator) and the button
A flashes.
By pressing button A you can switch
the rinse-aid indicator off
or on .
Switch off the main switch
1
;
The setting is saved.
“Remember to switch on the rinse-aid refill
indicator again if you use a detergent
without an integrated rinse-aid!”
en
15
Switching the salt refill
indicator / water softening
system off and on
Close the door
Rotate the programme selector
3
from the 12 o’clock position by one
notch to the left.
Switch on main switch
1
and hold
down for at least 3 sec.
The digital display
8
indicates the
current set hardness value and the salt
refill indicator
6
flashes
(hardness value has been set to 4
at the factory).
To change the setting: Rotate the
programme selector
3
.
You can select a set value between
0 and 7 according to the hardness
of your water.
Switch off the main switch
1
.
The chosen setting has now been
stored.
Note
If you use the detergent and rinse aid
separately or switch from combined
detergents to standard cleaning products,
ensure that the rinse aid refill indicator has
been switched on and the water softening
system has been set to the correct water
hardness.
en
16
Programme overview
This overview lists the max. possible number of programmes. The programmes supplied with your
appliance are indicated on the fascia.
Type of crockery
e.g.china,
pots/pans,
cutlery,
glasses,
etc.
Type of food
remains
Amount of
food remains
Condition of
food remains
Wash
programme
Programme
sequence
Non-
delicate
Soups, casseroles,
sauces, potatoes,
pasta, rice, eggs,
roast or fried food
Soups, potatoes,
pasta, rice, eggs,
roast or fried food
Coffee, cakes,
milk, sausage,
cold drinks,
salads
a lot
very little
stuck on hard
Normal
65°
Intensive
70°
Eco
50°
Quick
45°
Pre-rinse
Rinse-aid
70°
Drying
Drying
Rinse-aid
70°
Drying
Main rinse Main rinse
Rinse-aid
55°
Wash
45°
Rinse-aid
65°
Wash
50°
Rinse off if
the dishes
have been
stacked for
several
days in the
dishwasher
prior to
washing.
Pre-rinse
Mixed
Delicate
Mixed
Gentle
40°
Pre-rinse
Wash
40°
Main rinse
Rinse-aid
55°
Drying
a little
loosely attached
Second
rinse
First rinse
Wash
65°
Pre-rinse
Pre-rinse
Third
rinse
Pre-rinse
50°
Wash
70°
First rinse
Second
rinse
Programme selection
The most appropriate programme can be
identified by comparing the type of
crockery, cutlery, etc., as well as the
amount and condition of food remains,
with the details contained in the
programme overview.
You will find the appropriate programme
information in the introduction.
en
17
Washing dishes
Reduce costs!
If only a small number of
dishes have been loaded into
the dishwasher, selecting a
programme that operates at
the next lowest temperature
will usually suffice.
Programme specifications
The programme specifications can be
found in the summary of instructions.
Programme specifications refer to normal
conditions. Greater deviations may occur
due to:
varying amounts of dishes
water supply temperature
water pipe pressure
ambient temperature
mains voltage tolerances
and the tolerances specific
to the appliance (e.g. temperature,
amount of water, etc.)
The water consumption values refer
to a set water hardness value of 4.
Switching on the appliance
Close the door.
Turn on the tap fully.
Rotate programme selector
3
to the
required programme.
Switch on the main switch
1
.
The expected programme duration
is indicated on the numerical
display
8
.
The programme sequence starts
automatically.
Remaining running time display
When the appliance has started, the
expected programme running time is
displayed. The programmed running time
is affected by the water temperature, the
number of dishes, as well as the degree
of soiling. If these conditions are changed,
the running time (depending on the
selected programme) can vary greatly.
As the effect is not detected until a
programme is running, the time may
be longer or shorter than expected.
End of programme
The programme has ended when a figure
appears in the numerical display
8
.
Switching the dishwasher OFF
Several minutes after the programme has
ended:
Set the main switch
1
to OFF.
Turn the water tap off.
(Does not apply when Aqua-Stop unit
has been fitted)
Remove dishes, etc. when they have
cooled down.
Warning
At the end of the programme please open
the door fully and not partially when
emptying the dishwasher. Any escaping
water vapour could damage sensitive
worktops.
en
18
Interrupting the programme
Set main switch
1
to OFF.
Indicator lights extinguish. The
programme is retained in the
dishwasher memory.
If the hot water was switched ON or the
appliance has already heated up and then
the appliance door opened, leave the door
ajar for several minutes and then close.
Otherwise, the appliance door may fly
open due to expansion.
In order to continue with the stored
programme, set the main switch to ON
again.
Terminating the programme
(Reset)
Only when the main switch is on:
Rotate programme selector to the
Reset position. The digital display
indicates after approx. 3 sec.
The programme sequence lasts
approx. 1 min.
When the programme has run,
switch off the main switch
1
.
To restart, rotate the programme selector
3
to the required programme. Switch on
the main switch
1
. The programme
sequence starts automatically.
Changing the programme
It is possible to change the programme
within 2 minutes after you have switched
the dishwasher on.
Should it be necessary to change the
programme after this period, the
programme cycle that has already been
begun (e.g. washing) will be completed
first of all.
The new remaining time displayed is the
sum of the remaining time from the
preceding programme cycle and the
remaining time attributable to the new
programme that has been selected.
Intensive drying
By activating the “Intensive drying”
function, the final rinse will produce
a higher temperature in all programmes
resulting in an improved drying result
(please note that higher temperatures
might have an effect on delicate items).
Close the door.
Hold down button B and
switch on main switch
1
.
Release both buttons.
The digital display
8
indicates
(on) or (off) and button B flashes.
To change the setting, press
button
B .
Switch off the main switch
1
; the
chosen setting has now been stored.
en
19
Additional functions *
* on some models additional functions
4
can be set with the buttons.
Pre-Soak *
The Pre-Soak programme option serves to
perform a pre-soak cycle before the main
programme. This cycle enables cookware,
e.g. pans, bowls, etc. to be pre-soaked
and pre-rinsed in the lower rack. If you
wish to pre-soak the dishes, this
programme option must be selected by
pressing the “Pre-Soak” button before the
programme starts. The recommended
detergent amount is approx. 5 g poured
onto the inside of the door.
Time reduction/ time saving *
Pressing the “Time reduction/time saving”
button provides a short wash cycle by
curtailing the drying phase and the
washing time. The washing and drying
performance will be reduced with the Time
reduction/time saving programme option.
Half load*
If you have only a few items to wash (e.g.
glasses, cups, plates), you can switch to
“Half load”. The “half load” additional
function saves water, energy and time. It is
recommended to put a little less detergent
in the detergent dispenser than for a full
load.
Extra dry*
If you press the “Extra dry” button, you
will receive a higher temperature in all
programmes in the final rinse and
therefore an improved drying result.
(please note that higher temperatures
might have an effect on delicate items).
h.
Time delay *
You can delay the start of the programme
in 1-hour steps up to 19 hours.
Switch on the appliance.
Press the timer programming button
until the digital display
8
jumps to
.
Keep pressing the timer programming
button until the required time is
displayed.
To delete the timer programming,
keep pressing the button until
is displayed.
You can change your programme
selection at any time until the
programme starts.
Saving time (VarioSpeed) *
The >>Save time<< function can reduce
the running time by approx. 20% to 50%
depending on the selected rinse
programme. The particular change in
the running time is indicated on the time
remaining display. To obtain optimum
cleaning and drying results at a reduced
running time, water and energy
consumption are increased.
en
20
Maintenance and care
A regular inspection and maintenance of
your machine will help to prevent faults.
This saves time and prevents problems.
Overall condition of the
machine
Check washing chamber for grease
and limescale deposits.
If you find such deposits:
Fill the detergent dispenser with
detergent, start the appliance without
utensils in the programme which has
the highest wash temperature.
Clean the appliance with detergents/
appliance cleaners which are particularly
suitable for use with dishwashers.
Regularly wipe the door seal with a
damp cloth.
Never use a steam cleaner to clean your
dishwasher. The manufacturer is not liable
for any consequential damage.
Regularly wipe the front of the appliance
and panel with a damp cloth; water and
a little washing-up liquid will suffice.
Do not use sponges with a rough surface
or abrasive detergents, as these could
scratch the surfaces.
Attention!
Never use other chlorinated household
detergents! Health hazard!
Salt and rinse aid
Check the refill indicators
6
7
.
If required, top up the salt and/or rinse
aid.
Filters
Waste which is deposited on the filters
28 may result in a blockage.
After each washing cycle check the
filters for residue.
Unscrew the filter cylinder and remove
the filters. The filters are permanently
attached to each other and cannot be
dismantled.
Remove large foreign objects. Clean
the filters under running water.
Re-installation:
Insert the filters and screw the filter
cylinder tight.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Bosch Free-standing dishwasher 60 cm white User manual
- Category
- Dishwashers
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Bosch Dishwasher User manual
-
Bosch SGS55E12EU/82 User manual
-
Bosch SGI45E16GB/29 Owner's manual
-
-
-
Bosch SGS46E12EU/04 User manual
-
Bosch SRS55M22TC/07 User manual
-
Bosch SRS55M38EU/18 User manual
-
Bosch SGS55E76EU/90 User manual
-
Bosch SGS55E02TC/01 User manual