ADC WFX-3900-16-L12 User manual

WFX-3900/3700/3500 Wireless LAN Array

User Manual

WFX-3900 (16-Port) WFX-3700 (8-Port) WFX-3500 (4-Port)

WFX-3900-16 L11

WFX-3900-16 L21

WFX-3900-16-L12

WFX-3900-16-L22

WFX-3700-8 L11

WFX-3700-8 L21

WFX-3700-8 L12

WFX-3700-8 L22

WFX-3500-4 L31

WFX-3500-4 L32

WFX-3900 Shown

Document Number:

AIWS-UM-4003-01

REVISION HISTORY

The Revision History provides a summary of any changes in this manual. Please make sure you are using the

latest revision of this manual.

December 22, 2005

This manual is available online at ADC’s website (www.adc.com/documentationlibrary/) or you can order copies

of the manual by contacting your sales representative. Please ask for document AIWS-UM-4003-01.

Copyright

Trademark Information

ADC is a registered trademark of ADC Telecommunications, Inc. No right, license, or interest to such trademarks is granted

hereunder, and you agree that no such right, license, or interest shall be asserted by you with respect to such trademark.

Other product names mentioned in this practice are used for identification purposes only and may be trademarks or regis-

tered trademarks of their respective companies.

Disclaimer of Liability

Information contained in this document is company private to ADC Telecommunications, Inc., and shall not be modified,

used, copied, reproduced or disclosed in whole or in part without the written consent of ADC.

Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice.

In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits, and ADC further

disclaims any and all liability for indirect, incidental, special, consequential or other similar damages. This disclaimer of

liability applies to all products, publications and services during and after the warranty period.

Revision Release Date Revisions Made

01 December 22, 2005 Initial Release

Table of Contents

AIWS-UM-4003-01 iii

About This Manual ..........................................................................................................xi

Introduction ...............................................................................................................................xi

Audience ...................................................................................................................................xi

Organization ..............................................................................................................................xi

Conventions .............................................................................................................................xii

Safety Warnings .......................................................................................................................xii

Inspecting Your Shipment .......................................................................................................xiii

Chapter 1: Overview ....................................................................................................... 1-1

Product Overview ..................................................................................................................... 1-1

Key Features and Benefits .......................................................................................................1-3

Product Specifications (WFX-3900 and WFX-3700) ................................................................1-5

Product Specifications (WFX-3500) ......................................................................................... 1-9

Chapter 2: Installation .................................................................................................... 2-1

Installation Prerequisites .......................................................................................................... 2-1

Planning Your Installation ......................................................................................................... 2-2

Installation Workflow ..............................................................................................................2-13

Unpacking the Array ...............................................................................................................2-13

Installing Your Wireless LAN Array ........................................................................................ 2-14

Powering Up the Wireless LAN Array .................................................................................... 2-21

Establishing Communication with the Array ...........................................................................2-22

Performing the Express Setup Procedure ............................................................................. 2-23

Installing the WFX-3900 Wall Mount Assembly ..................................................................... 2-26

Chapter 3: Web Management Interface (WMI) ............................................................. 3-1

An Overview ............................................................................................................................. 3-1

Contents ................................................................................................................................... 3-2

Structure ...................................................................................................................................3-3

Chapter 4: Configuration ............................................................................................... 4-1

Logging In ................................................................................................................................. 4-1

Making Configuration Changes to the Array ............................................................................ 4-1

Chapter 5: Command-Line Interface ............................................................................. 5-1

Establishing a Secure Shell (SSH) Connection ....................................................................... 5-1

Basic Commands .....................................................................................................................5-2

Command Modes .....................................................................................................................5-2

Selecting Interfaces ..................................................................................................................5-5

Commands ............................................................................................................................... 5-5

Table of Contents December 22, 2005

iv AIWS-UM-4003-01

Appendix A: Quick Reference Guide ..........................................................................A-1

Review of WMI Pages ..............................................................................................................A-1

Factory Default Settings ...........................................................................................................A-3

Keyboard Shortcuts ..................................................................................................................A-7

Appendix B: Troubleshooting .....................................................................................B-1

General Hints and Tips .............................................................................................................B-1

Frequently Asked Questions ....................................................................................................B-1

Appendix C: Product Support .....................................................................................C-1

Glossary ......................................................................................................................GL-1

List of Figures

AIWS-UM-4003-01 v

Figure 1-1. Wireless Coverage Patterns .............................................................................1-1

Figure 1-2. Remote DC Power Distribution ........................................................................1-2

Figure 1-3. Layout of IAPs (WFX-3900) .............................................................................1-3

Figure 1-4. Antenna Patterns ..............................................................................................1-4

Figure 2-1. Wall Thickness Considerations ........................................................................2-2

Figure 2-2. Unit Placement .................................................................................................2-3

Figure 2-3. Full (Normal) Coverage ....................................................................................2-4

Figure 2-4. Adjusting RF Patterns .......................................................................................2-4

Figure 2-5. Custom Coverage .............................................................................................2-4

Figure 2-6. Calculating the Area of a Circle ........................................................................2-5

Figure 2-7. Sample 802.11a Cells .......................................................................................2-6

Figure 2-8. Transmit Power .................................................................................................2-7

Figure 2-9. Overlapping Cells .............................................................................................2-7

Figure 2-10.Allocating Channels Manually ..........................................................................2-8

Figure 2-11.Deployment Scenario (54 Mbps)—Per Sector .................................................2-8

Figure 2-12.Deployment Scenario (36 Mbps)—Per Sector .................................................2-9

Figure 2-13.Deployment Scenario (18 Mbps)—Per Sector .................................................2-9

Figure 2-14.Port Failover Protection ..................................................................................2-10

Figure 2-15.Switch Failover Protection ..............................................................................2-10

Figure 2-16.Installation Workflow ......................................................................................2-13

Figure 2-17.Array Placement .............................................................................................2-14

Figure 2-18.Attaching the T-Bar Clips ................................................................................2-16

Figure 2-19.Installing the Mounting Plate (WFX-3900 shown) ..........................................2-17

Figure 2-20.Connecting the Cables ...................................................................................2-18

Figure 2-21.Attaching the Unit (WFX-3900) ......................................................................2-19

Figure 2-22.Attaching the Unit (WFX-3500) ......................................................................2-20

Figure 2-23.Securing the Array ..........................................................................................2-20

Figure 2-24.IAP Positions (WFX-3900) .............................................................................2-21

Figure 2-25.LED Locations (WFX-3900) ...........................................................................2-22

Figure 2-26.Network Interface Ports ..................................................................................2-22

Figure 2-27.WMI: Time Zone .............................................................................................2-25

Figure 2-28.Enabling the NTP Feature ..............................................................................2-25

Figure 2-29.Wall Mount—Marking the Holes .....................................................................2-26

Figure 2-30.Installing the Toggle Bolts ...............................................................................2-27

Figure 2-31.Attaching the Wall Mounting Plate .................................................................2-28

Figure 2-32.Mounting the Array on a Wall .........................................................................2-29

Figure 3-1. Web Management Interface .............................................................................3-1

List of Figures December 22, 2005

vi AIWS-UM-4003-01

Figure 3-2. WMI: Frames ....................................................................................................3-3

Figure 3-3. WMI: Status Bar ................................................................................................3-4

Figure 4-1. WMI: Logging In to the Wireless LAN Array .....................................................4-1

Figure 4-2. WMI: Array Status Page ...................................................................................4-2

Figure 4-3. Linked Items .....................................................................................................4-2

Figure 4-4. WMI: Disabled Device (Partial View) ................................................................4-2

Figure 4-5. IAP Cells ...........................................................................................................4-3

Figure 4-6. WMI: Express Setup Page (Part 1) ..................................................................4-4

Figure 4-7. WMI: Express Setup Page (Part 2) ..................................................................4-4

Figure 4-8. WMI: Time Zones .............................................................................................4-7

Figure 4-9. Enabling the NTP Feature ................................................................................4-7

Figure 4-10.WMI: Network Interfaces Page ........................................................................4-8

Figure 4-11.WMI: Network Settings Page (Part 1) ..............................................................4-9

Figure 4-12.WMI: Network Settings Page (Part 2) ..............................................................4-9

Figure 4-13.Network Interface Ports ..................................................................................4-10

Figure 4-14.WMI: Network Statistics Page ........................................................................4-12

Figure 4-15.WMI: DHCP Settings Page ............................................................................4-13

Figure 4-16.WMI: DNS Settings Page ...............................................................................4-14

Figure 4-17.WMI: IAP Interfaces Page ..............................................................................4-15

Figure 4-18.WMI: IAP Settings Page .................................................................................4-16

Figure 4-19.WMI: Global Settings Page ............................................................................4-18

Figure 4-20.WMI: Global Settings .11a Page ....................................................................4-19

Figure 4-21.Specifying 802.11a Data Rates ......................................................................4-20

Figure 4-22.WMI: Global Settings .11bg Page ..................................................................4-21

Figure 4-23.Specifying 802.11g Data Rates ......................................................................4-21

Figure 4-24.Specifying 802.11b Data Rates ......................................................................4-22

Figure 4-25.WMI: IAP LED Settings Page .........................................................................4-23

Figure 4-26.WMI: Statistics Page ......................................................................................4-24

Figure 4-27.WMI: Statistics for IAP a4 Page (WFX-3700) ................................................4-25

Figure 4-28.WMI: Statistics for All IAPs Page (WFX-3700) ...............................................4-26

Figure 4-29.WMI: SSID Page ............................................................................................4-27

Figure 4-30.WMI: SSID Management Page ......................................................................4-28

Figure 4-31.WMI: Security Page .......................................................................................4-30

Figure 4-32.WMI: Security Management Page .................................................................4-31

Figure 4-33.WMI: Radius Server Page ..............................................................................4-34

Figure 4-34.WMI: Radius User Page .................................................................................4-35

Figure 4-35.WMI: MAC Access List Page .........................................................................4-36

December 22, 2005 List of Figures

AIWS-UM-4003-01 vii

Figure 4-36.WMI: Admin Management Page ....................................................................4-37

Figure 4-37.WMI: Rogue AP List Page .............................................................................4-38

Figure 4-38.WMI: Rogue Control List Page .......................................................................4-39

Figure 4-39.WMI: Stations Page ........................................................................................4-40

Figure 4-40.WMI: Services Page .......................................................................................4-40

Figure 4-41.WMI: Time Settings Page ...............................................................................4-41

Figure 4-42.WMI: System Log Page .................................................................................4-42

Figure 4-43.WMI: SNMP Page ..........................................................................................4-43

Figure 4-44.WMI: Array Info Page .....................................................................................4-44

Figure 4-45.WMI: Tools Page ............................................................................................4-44

Figure 4-46.WMI: Show Config Page ................................................................................4-45

Figure 4-47.WMI: Event Log Page ....................................................................................4-46

Figure 5-1. Command Line Interface ..................................................................................5-1

Figure A-1. Disconnecting Power from the Array ................................................................A-1

Figure A-2. Removing the Access Panel Screws ................................................................A-2

Figure A-3. Removing the Access Panel ............................................................................A-3

Figure A-4. Disconnecting the Power Supply and Fan .......................................................A-3

Figure A-5. Reconnecting the Fan and Power Supply ........................................................A-4

Figure A-6. Reinstalling the Access Panel ..........................................................................A-4

Figure A-7. Removing the FLASH Memory Module ............................................................A-5

Figure A-8. Removing the DIMM Memory Module ..............................................................A-6

Figure A-9. Removing the Chassis Cover Nylon Screws ....................................................A-7

Figure A-10.Removing the Chassis Cover ..........................................................................A-7

Figure A-11.Lifting the Integrated Access Point Module ......................................................A-8

Figure A-12.Disconnect the Integrated Access Point Module .............................................A-8

Figure A-13.Installing a New Access Panel (with Power Supply) .......................................A-9

List of Figures December 22, 2005

viii AIWS-UM-4003-01

List of Tables

AIWS-UM-4003-01 ix

Table 2-1.Serial Connection Settings ..................................................................................2-1

Table 2-2.Recommended Cell Sizes per Data Rate ...........................................................2-5

Table 2-3.Port Failover Protection .....................................................................................2-10

Table 2-4.Deployment Summary .......................................................................................2-12

Table 2-5.Parts and Equipment .........................................................................................2-13

Table B-1.Serial ...................................................................................................................B-3

Table B-2.Gigabit 1 and Gigabit 2 .......................................................................................B-3

Table B-3.Fast Ethernet .......................................................................................................B-3

Table B-4.Integrated Access Points (IAPs) .........................................................................B-4

Table B-5.DHCP ..................................................................................................................B-4

Table B-6.External RADIUS .................................................................................................B-4

Table B-7.Internal RADIUS ..................................................................................................B-5

Table B-8.NTP .....................................................................................................................B-5

Table B-9.Syslog ..................................................................................................................B-5

Table B-10.SNMP ................................................................................................................B-5

Table B-11.Default SSID ......................................................................................................B-6

Table B-12.Encryption ..........................................................................................................B-6

Table B-13.Administrator Account and Password ...............................................................B-6

Table B-14.Management ......................................................................................................B-7

List of Tables December 22, 2005

x AIWS-UM-4003-01

AIWS-UM-4003-01 xi

ABOUT THIS MANUAL

INTRODUCTION

This User’s Guide provides essential information about the ADC

®

Wireless LAN Array (also referred to throughout

this document as “the Array”).

AUDIENCE

This manual is written for wireless network administrators who will install, configure and manage the Array and

assumes you are familiar with ADC hardware, cabling, electronic circuitry, and wiring practices.

ORGANIZATION

This manual includes the following chapters:

Chapter Description

Chapter 1: Overview Introduces the Wireless LAN Array, including an overview of its

key features and benefits and a detailed listing of the product’s

physical, environmental, and regulatory specifications.

Chapter 2: Installation Defines the prerequisites for installing the Array and provides

instructions to help you complete a successful installation.

Chapter 3: Web Management Interface (WMI) Provides an overview of the Array’s embedded Web

Management Interface (WMI), used for establishing your

network’s configuration settings and wireless operating

parameters.

Chapter 4: Configuration Addresses configuration and management tasks using the

product’s embedded Web Management Interface (WMI). It also

includes a procedure for logging in to the Array with your Web

browser.

Chapter 5: Command-Line Interface Covers configuration and management tasks using the product’s

Command Line Interface (CLI), and includes a procedure for

establishing a Telnet connection to the Array.

Appendix A: Servicing the Array Contains procedures for servicing the Array, including the

removal and reinstallation of major hardware components.

Appendix A: Quick Reference Guide Contains product reference information. Use this chapter to

locate the information you need quickly and efficiently.

Appendix B: Troubleshooting Provides information that can help you resolve technical

difficulties. Before contacting ADC, review all sections in this

chapter and try to determine if your problem resides with the

Array or your network infrastructure.

Appendix C: Product Support Provides contact information for the ADC Technical Support

group.

Glossary Defines terms referred to in this User’s Guide.

About This Manual December 22, 2005

xii AIWS-UM-4003-01

CONVENTIONS

The following style conventions and terminology are used throughout this guide.

SAFETY WARNINGS

Element Meaning

Bold font Text that you must input exactly as shown (e.g., type 1 for card 1), menu buttons

(e.g., ACCEPT SHELF OPTIONS) or menu screen options (e.g., ALARMS screen) that

you must select

Italic font Variables that you must determine before inputting the correct value (e.g., Password )

Monospace font References to screen prompts (e.g., Invalid Password...Try Again:.)

Reader Alert Meaning

Alerts you to supplementary information

!

IMPORTANT

Alerts you to supplementary information that is essential to the completion of a task

ATTENTION

Alerts you to possible equipment damage from electrostatic discharge

CAUTION

Alerts you to possible data loss, service-affecting procedures, or other similar type

problems

WARNING

Alerts you that failure to take or avoid a specific action might result in hardware damage or

loss of service

DANGER

Alerts you that failure to take or avoid a specific action might result in personal harm

CAUTION

Read all user documentation before powering this device. All ADC interconnected equipment

should be contained indoors. This product is not suitable for outdoor operation. Please verify the

integrity of the system ground prior to installing the equipment. Additionally, verify that the

ambient operating temperature does not exceed 50°C.

DANGER

Do not operate this device near unshielded blasting caps or in an explosive environment unless

the device has been modified to be especially qualified for such use.

DANGER

Do not work on this device or connect or disconnect cables during periods of lightning activity.

CAUTION

This product relies on the building’s installation for over current protection. Ensure that a fuse or

circuit breaker no larger than 120 VAC, 15A (U.S.) or 240 VAC, 10A (International) is used on all

current-carrying conductors.

December 22, 2005 About This Manual

AIWS-UM-4003-01 xiii

INSPECTING YOUR SHIPMENT

Upon receipt of the equipment:

• Unpack each container and visually inspect the contents for signs of damage. If the equipment has been dam-

aged in transit, immediately report the extent of damage to the transportation company and to ADC. Order

replacement equipment, if necessary.

• Check the packing list to ensure complete and accurate shipment of each listed item. If the shipment is short

or irregular, contact ADC as described in Appendix C: Product Support on page C-1. If you must store the

equipment for a prolonged period, store the equipment in its original container.

About This Manual December 22, 2005

xiv AIWS-UM-4003-01

AIWS-UM-4003-01 1-1

1

Chapter

OVERVIEW

This chapter introduces the Wireless LAN Array, including an overview of its key features and benefits, and a

detailed listing of the product’s physical, environmental, technology and regulatory specifications. Topics discussed

in this chapter include:

• “Product Overview” on page 1-1

• “Key Features and Benefits” on page 1-3

• “Product Specifications (WFX-3900 and WFX-3700)” on page 1-5

• “Product Specifications (WFX-3500)” on page 1-9

PRODUCT OVERVIEW

The Wireless LAN Array is a high capacity, multi-mode device designed for the Enterprise market, with twice the

range and up to sixteen times the capacity of competitive wireless products.

Wireless LAN Array (WFX-3900/3700/3500)

1

The Array (regardless of product model) is Wi-Fi

®

compliant and simultaneously supports 802.11a, 802.11b, and

802.11g clients. Enterprise class features such as VLAN support and multiple SSID capability enable robust

network compatibility and a high level of scalability and system control. The optional Wireless Management

System (WFX-3300) allows global management of hundreds of Arrays from a central location.

Enterprise Class Security

The latest and most effective wireless encryption security standards, including WPA (Wi-Fi Protected Access) with

802.11i AES (Advanced Encryption Standard) are provided with the Array. In addition, the use of an embedded

RADIUS server (or 802.1x with an external RADIUS server) ensures user authentication—multiple Arrays can

authenticate to the optional WFX-3300 ensuring only authorized Wireless LAN Arrays become part of the wireless

network. Rogue AP detection and site monitoring is performed in the background by the Array automatically.

Deployment Flexibility

ADC’s unique multi-radio architecture generates 360 degrees of sectored high-gain 802.11a/b/g coverage that

provides extended range and the highest possible data rates for a large volume of clients. Each sector can be

controlled automatically or manually, creating a pattern of wireless coverage perfectly tailored to individual customer

needs. For example:

Figure 1-1. Wireless Coverage Patterns

1. The WFX-3700 and WFX-3500 versions of the Wireless LAN Array deliver a lower capacity than the WFX-3900.

outside wall

Chapter 1: Overview December 22, 2005

1-2 AIWS-UM-4003-01

Figure 1-1 on the previous page depicts the following two scenarios:

• Full pattern coverage – All radios are activated with coverage spanning 360 degrees. If within range, clients

will always receive coverage regardless of their geographic position relative to the Array.

• Partial pattern coverage – If desired, the Array can be deployed close to an exterior wall. In this case, half of all

available radios have been deactivated to prevent redundant signals from “bleeding” beyond the site’s perimeter

wall. This configuration may also be used in those cases where you want to restrict wireless coverage to

selected areas of the building’s interior.

Remote DC Power System (Optional)

The Remote DC Power System (WFX-3100) provides distributed DC power to your Array (DC version)

deployments, eliminating the need to provide an AC power outlet in close proximity to the unit(s). In the following

example (Figure 1-2), DC power is supplied to four Arrays while utilizing only one AC power outlet.

Figure 1-2. Remote DC Power Distribution

Enterprise Class Management

The Array can be configured with its default RF settings, or the RF settings can be customized using the Array’s

embedded Web Management Interface (WMI). The WMI enables easy configuration and control from a graphical

console, along with a full compliment of troubleshooting tools, reports and statistics.

In addition, a fully featured Command Line Interface (CLI) offers IT professionals a familiar management and control

environment. SNMP (Simple Network Management Protocol) is also supported to allow management from an

SNMP compliant management tool, such as the optional Wireless Management System.

Note: For deployments of more than two Arrays, ADC recommends you use the Wireless Management

System (WFX-3300). The WFX-3300 enables control of large deployments.

AC Input to WFX-3100

DC Output to Arrays

WFX-3100

December 22, 2005 Chapter 1: Overview

AIWS-UM-4003-01 1-3

KEY FEATURES AND BENEFITS

This section describes some of the key product features and the benefits you can expect when deploying the Array

(the WFX-3900 product is highlighted in this section).

High Capacity and High Performance

The WFX-3900 easily handles time-sensitive traffic, such as voice, and can enable wireless connectivity for 1,024

users. The unit includes two Gigabit uplink ports for connection to the wired network. A total of sixteen IAPs provides

a maximum wireless capacity of 864 Mbps, which offers ample reserves for the high demands of current and future

applications. Of the sixteen IAPs, twelve operate in the 802.11a mode and four operate in any combination of

802.11a, 802.11b, and 802.11g.

If desired, IAP (radio) abg2 can also be configured in RF monitoring and rogue AP detection mode.

Figure 1-3. Layout of IAPs (WFX-3900)

Extended Coverage

One WFX-3900 solution enables you to replace up to sixteen access points (includes one omnidirectional IAP for

monitoring the network). Fifteen IAP radios with integrated directional antennas provide increased wireless range

and enhanced data rates in all directions. With an Array deployed, far fewer access points are needed for your

wireless network. Radio abg2 (see Figure 1-3) can be switched to use an integrated omnidirectional antenna—for

listening only—and can be dedicated to the tasks of site monitoring and rogue AP detection.

a1

abg1

a2

a3

a4

abg2 (RF monitoring)

a5

a6

a7

abg3

a8

a9

a10

abg4

a11

a12

Mode(s) IAP number

Chapter 1: Overview December 22, 2005

1-4 AIWS-UM-4003-01

Figure 1-4. Antenna Patterns

Non-Overlapping Channels

Complete use of non-overlapping channels limits interference and delivers maximum capacity. On the WFX-3900,

all 16 non-overlapping channels are fully utilized across the 5Ghz and 2.4Ghz spectrums (12 across the 5GHz

spectrum and 4 across the 2.4GHz spectrum).

Secure Wireless Access

Multiple layers of authentication and encryption ensure secure data transmissions. The Array is 802.11i compliant

with encryption support for 64 bit and 128 bit WEP, and WPA with TKIP and AES encryption.

Authentication support is provided via 802.1x, including PEAP, EAP-TLS, and EAP-TTLS.

Applications Enablement

QoS (Quality of Service) functionality combined with true switch capabilities enable high density Voice over Wireless

LAN deployments. Compliant with 802.1p and 802.1q standards.

SDMA Optimization

SDMA (Spatial Division Multiple Access) technology provides full 360° coverage while allowing independent

channel and power output customization. Also supports fast inter-zone handoffs for time-sensitive applications and

roaming support.

Easy Deployment

The Wireless Management System (WFX-3300) offers real time monitoring and management capabilities of the

wireless network—ideal for the Enterprise market. It also allows you to import floor plans to help you plan your

deployment. The Wireless LAN Array chassis has a plenum rated, lockable and tamper resistant case.

Array

802.11a (directional) 802.11a/b/g (directional)

802.11a/b/g (omnidirectional)

December 22, 2005 Chapter 1: Overview

AIWS-UM-4003-01 1-5

PRODUCT SPECIFICATIONS (WFX-3900 AND WFX-3700)

Element Specifications

Number of Users Maximum of 64 associated users per radio

1024 users per Array (WFX-3900)

512 users per Array (WFX-3700)

Physical Diameter: 18.65 inches (47.37 cm)

Height: 3.87 inches (9.83 cm)

Weight: 9 lbs (4.08 kg)

Environmental Operating Temperature:

-10°C to 50°C

0% to 90% relative humidity (non-condensing)

Storage Temperature:

-20°C to 60°C

5% to 95% relative humidity (non-condensing)

Maximum Operating Altitude:

2000 meters (6561 feet)

System 825 MHz CPU

128MB RAM, expandable

512MB system flash, expandable

Expansion slot for future options

Electrical Input Power (AC version): 90VAC to 265VAC at 47Hz to 63Hz

Input Power (DC version): 48VDC

Interfaces Serial:

1 x RS232 – RJ45 connector

Ethernet Interfaces:

2 x Gigabit 10/100/1000 Mbps w/failover

1 x Fast Ethernet 10/100 Mbps

Status LEDs:

System status, Ethernet, Radio

Chapter 1: Overview December 22, 2005

1-6 AIWS-UM-4003-01

Management Web-based HTTPS

SNMP v3

CLI via SSHv2 or Telnet

FTP

TFTP

Serial

Proprietary

Wireless Management System

Syslog reporting for alerts/alarms

Networking DHCP client, DHCP server, NTP client

RFC

VLAN Support 802.1Q, P VLAN

Supports up to 16 VLANs

Multiple SSID Support Allows up to 16 separate SSIDs to be defined with map security, VLAN

and QoS settings for each SSID

Performance Client Load Balancing:

Automatic load balancing between system radios

Quality of Service:

802.1P wired traffic prioritization

Wireless packet prioritization

MAP CoS to TCID

Fair queuing of downstream traffic

Element Specifications

Page is loading ...

ADC WFX-3900-16-L12 User manual

This manual is also suitable for

ADC WFX-3900-16-L12 User manual

Related papers

Other documents