Vulcan-Hart VE40-ML-126850 User manual

Brand: Vulcan-Hart

Model: VE40-ML-126850

Category: Small kitchen appliances

Type: User manual

This manual is also suitable for

A product of VULCAN-HART LOUISVILLE, KY 40201-0696

F35410 (May 2003)

- NOTICE -

This Manual is prepared for the use of trained Vulcan Service

Technicians and should not be used by those not properly

qualified. If you have attended a Vulcan Service School for this

product, you may be qualified to perform all the procedures

described in this manual.

This manual is not intended to be all encompassing. If you have

not attended a Vulcan Service School for this product, you should

read, in its entirety, the repair procedure you wish to perform to

determine if you have the necessary tools, instruments and skills

required to perform the procedure. Procedures for which you do

not have the necessary tools, instruments and skills should be

performed by a trained Vulcan Service Technician.

Reproduction or other use of this Manual, without the express

written consent of Vulcan, is prohibited.

VE40 SHOWN

SERVICE MANUAL

ELECTRIC BRAISING PANS

(30 & 40 GALLON)

VE30 ML-126849

VE40 ML-126850

For additional information on Vulcan-Hart Company or to locate an authorized parts

and service provider in your area, visit our website at www.vulcanhart.com.

ELECTRIC BRAISING PAN

F35410 (May 2003) Page 2 of 32

TABLE OF CONTENTS

GENERAL ................................................................................ 3

Installation, Operation and Cleaning ......................................................... 3

Introduction ............................................................................ 3

Control Panel ...................................................................... 3

Model Designations ................................................................. 3

Tools................................................................................. 3

Specifications .......................................................................... 4

REMOVAL AND REPLACEMENT OF PARTS .................................................... 4

Covers and Panels ...................................................................... 4

Power Supply Box Components ............................................................ 5

Temperature Controller .................................................................. 6

Pan Position/Down Limit Switch ............................................................ 7

Up Limit Switch......................................................................... 9

Lid Switch ............................................................................. 9

Thermocouple Probe .................................................................... 9

DC Lift Motor ......................................................................... 10

Gear Reducer ......................................................................... 11

Heating Elements ...................................................................... 12

High Limit Thermostat .................................................................. 13

Lid Springs ........................................................................... 13

SERVICE PROCEDURES AND ADJUSTMENTS ................................................. 15

Temperature Controller Calibration ........................................................ 15

Temperature Controller Test ............................................................. 16

Thermocouple Test .................................................................... 16

Heating Element Test ................................................................... 17

DC Motor Controller Test ................................................................ 17

Pan Position/Down Limit Switch Adjustment ................................................. 18

Lid Switch Adjustment .................................................................. 19

Lid Spring Tension Adjustment............................................................ 20

ELECTRICAL OPERATION .................................................................. 21

Component Function ................................................................... 21

Component Location ................................................................... 22

Sequence of Operation .................................................................. 23

Schematic Diagram .................................................................... 25

Wiring Diagrams....................................................................... 26

Heating Element Circuits ............................................................ 26

Terminal Block Wiring .............................................................. 27

TROUBLESHOOTING ...................................................................... 28

Electric Heating (Manual Lift or Motorized Lift Option) .......................................... 28

Motorized Lift Option Only ............................................................... 29

CONDENSED SPARE PARTS LIST ........................................................... 32

ELECTRIC BRAISING PAN

F35410 (May 2003)

Page 3 of 32

GENERAL

INSTALLATION, OPERATION

AND CLEANING

Refer to the Installation & Operation Manual for

specific instructions.

INTRODUCTION

The tilting braising pan (skillet) is a versatile piece

of cooking equipment. It can be used to stew,

simmer, steam, sear, pan fry, grill or saute food

products over an evenly distributed heating surface.

Once the product is fully cooked, the pan can be

tilted for ease of product removal.

Control Panel

Model Designations

! VE30 - 30 gallon capacity

! VE40 - 40 gallons capacity

TOOLS

Standard

! Standard set of hand tools.

! VOM with an AC current tester.

NOTE: Any quality VOM with a sensitivity of

20,000 ohms per volt can be used.

! Temperature tester (thermocouple type) with

surface probe.

Special

! 1 5/8" open end wrench. Used for removing lid

springs and adjusting lid spring tension.

! Field service grounding kit P/N TL- 84919.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003) Page 4 of 32

SPECIFICATIONS

VOLTS PHASE

AMPERAGE PER LINE

VE30 VE40

TOTAL

L1-L3

TOTAL

L1 L2 L3

208 1 9 43 12 58 58 ---

2401 1250166767---

208 3 9 25 12 39 39 25

2403 122916464629

4803 121516232315

NOTES:

1. Amperage values in the table are nominal. Tolerance is +5/-10%.

2. Voltage values are @ 60HZ.

3. All models are shipped for 208/240V three phase connections. If a 208/240V single phase connection is

needed, the machine is field convertible at the terminal block. See wiring diagram AI1378.

4. On all 208V machines, the 240V heating element is being used (total KW output is reduced).

5. On VE40 three phase machines only, the heating elements are wired to be an unbalanced load.

REMOVAL AND REPLACEMENT OF PARTS

COVERS AND PANELS

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

Front, Rear & Side Panels

1. Lift up on the bottom edge of panel until it clears

the catch.

2. Tilt outwards and allow the panel to drop down.

3. Reverse procedure to install.

Control Panel

1. Remove front panel.

2. Disconnect conduit from control box.

3. Remove manual lift crank handle (if installed).

4. Remove bolts securing control panel to braising

pan frame. Bolts are recessed in the frame

channel.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003)

Page 5 of 32

5. Tilt bottom of control panel outwards and pull

down.

NOTE: The control panel should be supported to

remove lead wire strain.

6. Remove control box from control panel.

7. Disconnect lead wires from control switch.

8. Pull temperature dial from potentiometer shaft

and remove mounting nut.

9. Control panel is removed.

10. To install.

A. Align tab on potentiometer with positioning

bracket on panel.

B. Install mounting nut and tighten.

C. Adjust stop nut on potentiometer body (as

necessary) to ensure a water tight seal on

mounting nut.

D. Attach temperature dial.

11. Reverse procedure from step 6 to complete the

installation.

12. Check calibration as outlined under

TEMPERATURE CONTROLLER

CALIBRATION.

POWER SUPPLY BOX

COMPONENTS

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

CAUTION: Certain components in this system

are subject to damage by electrostatic discharge

during field repairs. A field service grounding kit

is available to prevent damage. The field service

grounding kit must be used anytime a control

board is handled.

1. Remove front panel as outlined under

COVERS AND PANELS.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003) Page 6 of 32

2. Remove power supply box cover.

Disconnect lead wires then remove the

component being replaced

4. Reverse procedure to install the replacement

component.

5. Check braising pan for proper operation.

TEMPERATURE CONTROLLER

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Remove control box from the control panel as

outlined under COVERS AND PANELS.

2. Disconnect lead wires from temperature

controller.

3. Remove temperature controller from control

box.

4. Pull temperature dial from potentiometer shaft

and remove mounting nut.

5. To install:

A. Align tab on potentiometer with positioning

bracket on panel.

B. Install mounting nut and tighten.

C. Adjust stop nut on potentiometer body (as

necessary) to ensure a water tight seal on

mounting nut.

D. Attach temperature dial.

6. Reverse procedure from step 3 to complete the

installation.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003)

Page 7 of 32

LEFT SIDE VIEW SHOWN

TOP VIEW SHOWN

7. Check calibration as outlined under

TEMPERATURE CONTROLLER

CALIBRATION.

PAN POSITION/DOWN LIMIT

SWITCH

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Remove front and left side panels as outlined

under COVERS AND PANELS.

2. Remove strain relief nut from end of strain

relief body and remove pan position/down limit

switch from switch mounting bracket.

3. Remove cover from switch.

4. Disconnect lead wires and pull wires thru strain

relief body.

5. Remove strain relief body from switch.

NOTE: When installing, ensure the o-ring seal is

inserted into the strain relief body (around power

cable) before tightening strain relief nut.

6. To install:

A. Position the switch with the head pointing

toward installer and gear cam pointing up.

NOTE: The plunger on the head is spring loaded

and will push the head away from switch body when

the last screw is removed.

B. Remove screws securing the head to

switch body, rotate 90° clockwise and

tighten screws to secure.

C. Place switch on its side with the head to

the left and gear cam pointing up.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003) Page 8 of 32

SIDE VIEW SHOWN

D. Align roller arm adaptor with the four

locking tabs pointing up and position one

of the tabs at 0°.

NOTE: The 0° position of the roller arm locking tab

is the starting point for alignment only. The locking

tab cannot remain at the 0° position.

E. Place roller arm adaptor on the gear cam

to engage the teeth. Lift the adaptor until

the teeth just slightly disengage from the

gear cam. Rotate the roller arm adaptor

counterclockwise 1 tooth, re-engage teeth

and release the adaptor.

F. Align the roller arm slots with the four

locking tabs on the roller arm adaptor and

tighten mounting screw to secure.

G. Verify roller arm position on switch.

1) Measure the distance from the rear of

the switch body to the center of the

roller. The distance should be 3".

H. If distance is ok, proceed to step 7.

I. If distance is not ok, adjust the roller arm

position (as necessary) to obtain the 3"

roller arm dimension.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003)

Page 9 of 32

7. Reverse procedure from step 5 to complete the

installation.

8. Adjust pan position/down limit switch on switch

mounting bracket as outlined under PAN

POSITION/DOWN LIMIT SWITCH

ADJUSTMENT in SERVICE PROCEDURES

AND ADJUSTMENTS.

UP LIMIT SWITCH

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Remove front panel as outlined under

COVERS AND PANELS.

2. Disconnect lead wires

from switch.

Remove switch from mounting bracket.

4. Reverse procedure to install and check for

proper operation.

LID SWITCH

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Remove lid switch cover from lid switch

support bracket.

2. Remove switch from lid support bracket.

3. Lift terminal cover off switch body and

disconnect lead wires.

4. Reverse procedure to install and adjust switch

as outlined under LID SWITCH ADJUSTMENT

in SERVICE PROCEDURES AND

ADJUSTMENTS.

THERMOCOUPLE PROBE

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Access temperature controller as outlined under

TEMPERATURE CONTROLLER .

2. Disconnect thermocouple lead wires.

3. Raise the pan to the full tilt position.

Remove harness cover.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003) Page 10 of 32

5. Remove the insulation cover.

6. Loosen lock nut and remove threaded probe

from pan.

7. Reverse procedure to install and check braising

pan for proper operation.

NOTE: When installing: Route thermocouple wire in

the same manner thru the metal clamps on the hinge

& frame. Tighten thermocouple just until it touches

the pan; do not over tighten or damage to the

thermocouple may occur.

DC LIFT MOTOR

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Remove front, rear and right side panels as

outlined under COVERS AND PANELS.

2. Remove power supply box cover.

3. Disconnect DC lift motor lead wires labeled

MTR+ (positive) & MTR - (negative).

NOTE: Lead wires can be identified by label or

marking on the wire.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003)

Page 11 of 32

VE30 REAR VIEW SHOWN

4. Loosen the strain relief nut and the hold down

clamps for the motors' power cable. Pull the

cable thru the strain relief opening and remove

the cable from underneath the clamps.

5. Remove motor mounting bolts from gear

reducer flange.

6. Remove motor from gear reducer.

7. To install:

A. With drive key on shaft, install motor to

gear reducer.

B. Route and secure the motors' power cable

and re-connect motor lead wires.

C. Replace power supply box cover and side

panels.

8. Check for proper operation.

GEAR REDUCER

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Remove right side and rear panels as outlined

under COVERS AND PANELS.

2. Lower the pan (use motorized pan lift or manual

crank handle).

3. If DC lift motor is installed, remove motor as

outlined under DC LIFT MOTOR.

4. Remove lock nut securing crank assembly to lift

arm.

5. Remove bolts securing gear reducer to braising

pan frame then remove gear reducer.

6. Loosen set screw on crank assembly and

remove the assembly from drive shaft.

7. Loosen set screw on shaft extension coupling

and remove the coupling from manual crank

shaft.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003) Page 12 of 32

8. To install:

A. With drive key on drive shaft, install crank

assembly and tighten set screw against

key.

B. With drive key on manual crank shaft,

install shaft extension coupling and tighten

set screw against key.

C. Place gear reducer in its mounting location

on frame. Position gear reducer so the

shaft extension coupling is aligned with the

opening in control panel; and the lift arm is

vertical and parallel to the crank assembly

when connected.

NOTE: On the bottom lift arm bushing, the bushing

head must

be positioned between the lift arm and

the crank assembly to create approximately 1/32"

spacing.

9. Reverse procedure from step 5 to complete the

installation.

10. Check for proper operation.

HEATING ELEMENTS

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Raise the pan to the full tilt position.

2. Remove harness cover.

3. Disconnect lead wires from the heating

element being replaced.

Remove the insulation cover.

5. Remove heating element clamps (spring

loaded) from the clamp holder then remove

heating element.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003)

Page 13 of 32

RIGHT SIDE REAR VIEW SHOWN

6. Reverse procedure to install and check for

proper operation.

HIGH LIMIT THERMOSTAT

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Raise the pan to the full tilt position.

2. Remove the harness cover.

3. Disconnect lead wires from the high limit

thermostat.

4. Remove thermostat from insulation cover.

5. Reverse procedure to install and check

braising pan for proper operation.

LID SPRINGS

WARNING: DISCONNECT THE

ELECTRICAL POWER TO THE

MACHINE AND FOLLOW LOCKOUT /

TAGOUT PROCEDURES.

1. Lower the lid to the full down position.

NOTE: For spring tension to be set correctly, both

the left and right side springs must be replaced.

2. Remove spring covers by prying up at the

bottom. The covers are held in place by tabs on

the bottom of cover.

3. Place a 1 5/8" wrench on the lid spring lock nut

and apply a downward force until locking pin

can be removed. Continue to hold lock nut in

place.

ELECTRIC BRAISING PANS - REMOVAL AND REPLACEMENT OF PARTS

F35410 (May 2003) Page 14 of 32

Caution: Do not release wrench while locking pin

is removed or damage to the braising pan may

occur.

A. Slowly release downwards force to remove

spring tension.

B. Rotate lid spring lock nut to the next hole

position then replace locking pin. Continue

until all spring tension is removed, one

position at a time.

C. Remove bolts securing the inside lid

bearing housing to the lid support bracket.

D. Remove lid bearing housing

, lid spring lock

nut and the spring, from spring mandrel.

4. To install:

A. Slide the spring onto the lid spring

mandrel. Insert spring into locator hole on

the lid spring retainer.

B. Slide the lid spring lock nut onto the lid

spring mandrel. Insert spring into locator

hole on the lid spring lock nut.

C. Replace

lid bearing housing.

5. Replace spring on the opposite side.

6. Adjust spring tension as outlined under LID

SPRING TENSION ADJUSTMENT IN

SERVICE PROCEDURES AND

ADJUSTMENTS.

ELECTRIC BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTS

F35410 (May 2003)

Page 15 of 32

SERVICE PROCEDURES AND ADJUSTMENTS

WARNING: CERTAIN PROCEDURES IN THIS SECTION REQUIRE ELECTRICAL TEST OR MEASUREMENTS

WHILE POWER IS APPLIED TO THE MACHINE. EXERCISE EXTREME CAUTION AT ALL TIMES. IF TEST

POINTS ARE NOT EASILY ACCESSIBLE, DISCONNECT POWER AND FOLLOW LOCKOUT / TAGOUT

PROCEDURES, ATTACH TEST EQUIPMENT AND REAPPLY POWER TO TEST.

TEMPERATURE CONTROLLER

CALIBRATION

NOTE: Verify condition of thermocouple as outlined

under THERMOCOUPLE TEST before proceeding.

1. At the geometric center on the pan cooking

surface, clean an area approximately 3" inches

in diameter.

2. Apply a thin layer of fresh cooking oil to the

cleaned area and place a temperature sensing

disk on the pan cooking surface.

3. Turn on/off switch on and set temperature dial

to 250°F.

4. Monitor the heat light (red) on the control panel.

When temperature controller is calling for heat,

light will be on. If temperature controller is

satisfied, light will be off.

A. Allow the temperature controller to cycle

three times to stabilize the pan

temperature.

B. Record the temperature when the

temperature controller cycles off and on for

the next three cycles.

5. Calculate the differential by subtracting the

temperature indicated when heat light goes out

from temperature indicated when heat light

comes on.

A. The differential calculated should be less

than 20°F.

1) If the differential is less

than 20°F,

temperature controller is functioning

properly.

a. Proceed to average temperature.

2) If the differential is more

than 20°F,

the temperature controller is

malfunctioning.

a. Install a replacement

temperature controller and check

calibration.

6. Calculate the average temperature by adding

the temperature indicated when the heat lamp

goes out to the temperature indicated when the

heat lamp comes on & divide this answer by 2.

A. If the average temperature is less

than

10°F of the dial setting, temperature

controller is properly calibrated.

B. If the average temperature is more

than

10°F of the dial setting, temperature

controller calibration must

be adjusted.

7. Using the temperature scale on the overlay as a

guide, align the edge on a short piece of tape to

the temperature calculated in step 6 and apply

tape to knob as a reference point.

8. Remove temperature dial from shaft.

9. Loosen screws on the back of dial.

A. Hold the knob and rotate dial to the edge of

the tape used for reference. This

adjustment offsets the indicated

temperature on the dial to the actual

temperature measured.

NOTE: With knob facing user, a clockwise

rotation increases temperature and a counter-

clockwise rotation decrease temperature.

B. Hold the dial & knob together to maintain

the adjusted setting and tighten screws.

10. Replace temperature dial on shaft.

11. Turn the temperature dial to the lowest setting

then back to 250°F.

ELECTRIC BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTS

F35410 (May 2003) Page 16 of 32

12. Repeat the average temperature calculation for

up to three attempts. Allow the pan to cycle at

least two times between adjustments before

performing the calculation.

13. If calibration is unsuccessful, the controller may

be malfunctioning and cannot be adjusted

properly. Install a replacement temperature

controller and check calibration.

TEMPERATURE CONTROLLER

TEST

NOTE: The controller is powered whenever supply

power is connected to the machine.

1. Lower the pan to the full down position.

2. Access the temperature controller as outlined in

REMOVAL AND REPLACEMENT OF PARTS.

3. Re-connect power to the machine.

4. Verify temperature controller is receiving

120VAC at terminals L1 & L2, polarity is correct

and machine is properly grounded.

5. Turn on/off switch on and set temperature dial

to 250/F.

6. Verify heat light (red) comes on and all heating

elements are energized.

A. If heat light and heating elements energize

but turn off within 10 seconds, verify

condition of thermocouple as outlined

under THERMOCOUPLE TEST.

NOTE: Temperature controller will de-energize

internal relay if the circuitry detects an open

thermocouple.

B. If heat light and heating elements do not

energize, verify internal relay contacts are

operating properly.

7. Disconnect lead wire labeled HT.0 from the

COM terminal on the controller.

8. Verify 24VAC between the disconnected HT.0

lead wire and ground.

A. If correct, re-connect lead wire to COM

terminal and proceed to step 9.

B. If incorrect, check transformer and the

on/off switch for proper operation.

9. Disconnect lead wire labeled HT.1 from the

N.O. terminal on the controller.

10. Verify 24VAC between N.O. terminal on the

temperature controller and ground.

A. If correct, internal relay contacts are

functioning properly. Reconnect lead wire

to the N.O. terminal. See Troubleshooting.

B. If incorrect, install a replacement

temperature controller and check for

proper operation.

THERMOCOUPLE TEST

1. Access the temperature controller as outlined

in REMOVAL AND REPLACEMENT OF

PARTS.

2. Remove thermocouple lead wires from

temperature controller.

3. Check the thermocouple for resistance.

A. If meter reads an overload (OL) condition

(open), or zero ohms (short) replace the

thermocouple and check temperature

controller for proper operation.

4. If resistance is measured, thermocouple is

good.

ELECTRIC BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTS

F35410 (May 2003)

Page 17 of 32

HEATING ELEMENT TEST

VOLTAGE

KW PER

ELEMENT

AMPS PER

ELEMENT

OHMS PER

ELEMENT

208 4 14.3 13.7

240 4 16.7 13.7

480 4 8.7 55.5

NOTES:

1. Values in the table are nominal.

Tolerance is +5/-10%.

2. Voltage values are @ 60HZ.

3. Resistance values (ohms) are @ room

temperature.

4. On all 208V machines, the 240V heating

element is being used (KW output is

reduced).

1. Access the heating elements as outlined in

REMOVAL AND REPLACEMENT OF PARTS.

2. Measure voltage at heating element terminals

and verify it against data plate voltage.

A. If voltage is incorrect

, see

TROUBLESHOOTING.

B. If voltage is correct

, check current draw

(amps) through the heating element lead

wires.

NOTE: This method is preferred over a

resistance check when a clamp on type amp

meter is available.

1) If current draw is correct then heating

element is functioning properly. See

table for proper values.

2) If current draw is not

correct, turn

on/off switch to OFF and disconnect

the electrical supply.

a. Replace heating element then

proceed to step 3.

C. If unable to check current draw, a

resistance check may

indicate a

malfunctioning element.

1) Turn the on/off switch off and

disconnect power to the machine.

2) Remove the lead wires from the

heating element and check

resistance (ohms). See table for

proper values.

3. Check for proper operation.

DC MOTOR CONTROLLER TEST

1. Lower the pan to the full down position.

2. Raise the lid to the full open position.

3. Access the DC motor controller as outlined

under POWER SUPPLY BOX COMPONENTS

in REMOVAL AND REPLACEMENT OF

PARTS.

4. Set VOM to measure AC volts and connect

meter leads at L1 & L2 on the controller.

5. Turn the on/off switch to on.

6. Verify 120VAC at L1 & L2 on the controller

when the lift control switch (momentary) is

operated to raise & lower the pan.

A. If voltage is present but pan does not raise

& lower, proceed to step 7.

B. If voltage is not present refer to

MOTORIZED LIFT OPTION ONLY under

TROUBLESHOOTING.

7. Disconnect power to the machine.

8. Set VOM to measure DC volts and connect

VOM leads to terminals A + (positive) & A -

(negative) on the controller.

9. Re-connect power to the machine.

10. Verify 90VDC (approximate) from the DC

motor controller when the lift control switch

(momentary) is operated to raise & lower the

pan.

ELECTRIC BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTS

F35410 (May 2003) Page 18 of 32

SIDE VIEW SHOWN

LEFT SIDE VIEW SHOWN

A. If voltage is present but pan does not

raise, refer to MOTORIZED LIFT OPTION

ONLY under TROUBLESHOOTING.

B. If voltage is not present and the fuse is ok,

turn the on/off switch off and disconnect

power to the machine.

11. Install a replacement DC motor controller and

check for proper operation.

PAN POSITION/DOWN LIMIT

SWITCH ADJUSTMENT

NOTE: Do not use the motorized lift (if installed) for

this procedure.

1. Turn the on/off switch off.

2. Remove front and left side panels as outlined

under COVERS AND PANELS.

3. Insert the manual crank handle.

4. Raise the pan to the full tilt position.

5. Verify roller arm position on switch.

A. Measure the distance from the rear of the

switch body to the center of the roller. The

distance should be 3".

B. If distance is ok, proceed to step 6.

C. If distance is not ok, position the roller arm

as outlined under PAN POSITION/DOWN

LIMIT SWITCH in REMOVAL AND

REPLACEMENT OF PARTS.

6. Lower the pan to the full down position. The

roller should make contact with the hinge and

operate the switch.

7. Verify pan position/down limit switch N.O.

contacts are closing.

A. Turn the on/off switch on and set the

temperature dial to call for heat.

B. Heat light (red) comes on and all heating

elements are energized.

1) If heating elements do not energize:

Verify 24VAC input to the switch and

24VAC is output from the switch.

2) If voltage is present on the output

side of the switch, the switch is

functioning properly. See

TROUBLESHOOTING.

3) If voltage is not present on the output

side of the switch, install a

replacement pan position/down limit

switch and repeat this procedure to

adjust.

8. Verify pan position/down limit switch N.O.

contacts are opening.

A. Slowly raise the pan until the heat light

and heating elements de-energize then

stop.

B. At the rear of the pan, measure the

distance from the bottom of the pan skirt

to the flat surface covering the frame.

1) Distance should be 2.25" to 2.50".

NOTE: For reference, this is approximately 5

angular degrees.

9. If heat light and heating elements de-energize;

and the measured distance is within the

acceptable range, switch is adjusted properly.

If both conditions are not satisfied, adjustment

is necessary.

10. To Adjust:

A. Loosen screws on the mounting switch

bracket.

ELECTRIC BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTS

F35410 (May 2003)

Page 19 of 32

LEFT SIDE VIEW SHOWN

B. Adjust mounting switch bracket up or

down (as necessary) to obtain the rear

pan dimension of 2.25" to 2.50".

11. Repeat steps 5 thru 9 to check for proper

operation.

LID SWITCH ADJUSTMENT

CAUTION: Lid switch should not allow pan to be

raised if the lid is not opened a minimum of 23"

or damage to the lid may occur.

1. Turn the on/off switch on.

2. Raise the lid to the full open position.

3. Lower the pan to the full down position.

4. Lower the lid to an open height dimension of

23" to 23 1/2" (minimum is 23").

NOTE: For reference, this is approximately 45

angular degrees.

5. The lid switch actuator should make contact

with the trigger (cam) and operate the lid

switch.

6. Operate the "lift control switch" to raise the

pan.

A. If pan raises, the lid switch is functioning

properly.

B. If pan does not raise, continue with

procedure.

7. Remove lid switch cover from lid support

bracket.

8. To adjust:

A. With the lid raised to an open height

dimension of 23" to 23 1/2" (minimum is

23"), loosen lid switch mounting screws

and adjust switch position to operate the

switch. Re-tighten screws.

ELECTRIC BRAISING PANS - SERVICE PROCEDURES AND ADJUSTMENTS

F35410 (May 2003) Page 20 of 32

RIGHT SIDE REAR VIEW SHOWN

B. If additional adjustment is necessary,

push up on the tip of the switch actuator to

slightly bend the actuator around the

mating edge of the trigger (cam).

C. Verify pan will raise by operating lift

control switch.

D. Repeat the adjustment (as necessary) and

check for proper operation.

LID SPRING TENSION

ADJUSTMENT

1. Raise the lid and release at several positions

thru the range of travel.

A. If lid remains in place, no adjustment is

necessary.

B. If lid does not remain in place (springs up

or falls down), continue with procedure.

NOTE: For spring tension to be set correctly, each

spring must be adjusted the same amount.

2. Remove spring covers by prying up at the

bottom. The covers are held in place by tabs

on the bottom of cover.

3. To adjust:

A. Place a 1 5/8" wrench on the lid spring

lock nut and apply a downward force until

locking pin can be removed. Continue to

hold lock nut in place.

CAUTION: Do not release wrench while locking

pin is removed or damage to the braising pan

may occur.

B. Apply additional downward force to

increase

spring tension; or slowly release

downwards force to decrease

spring

tension.

C. Rotate lid spring lock nut to the next hole

position then replace locking pin. Adjust

the spring tension, one position at a time.

D. Repeat tension adjustment on the

opposite spring.

4. Repeat step 1 to verify adjustment. Make

additional adjustments as necessary.

Page is loading ...

Vulcan-Hart VE40-ML-126850 User manual

Brand: Vulcan-Hart

Model: VE40-ML-126850

Category: Small kitchen appliances

Type: User manual

This manual is also suitable for

Download PDF

report

Vulcan-Hart VE40-ML-126850 User manual

This manual is also suitable for

Vulcan-Hart VE40-ML-126850 User manual

Related papers

Other documents