PlexiDor Performance Pet Doors PD WALL SM BR Installation guide

Brand: PlexiDor Performance Pet Doors

Model: PD WALL SM BR

Category: Pet care

Type: Installation guide

This manual is also suitable for

Plexidor

Pet Door Wall Kit Instruction

for All Sizes Plexidor

: S, M, L, XL;

BiteGuard KennelPlex

1113,1418, 1419 & 1825

and Plexidor

Electronic LG

Important Notes:

Contractors, Carpenters &

Handymen,

Please read these instructions.

They will save you time.

Inside and outside holes in the

wall surfaces are different

sizes and at different heights.

You may silicone or caulk the

outside frame and tunnel

pieces. But, Do Not

silicone

or caulk the inside frame of

the pet door. If you have mul-

tiple dogs or your door

receives rough usage, you

may need to replace a spring

in 5 years. And, we recom-

mend applying a few drops of

oil annually to the springs.

Outside Frame

Inside Frame

Plexidor

BiteGuard KennelPlex

Tunnel Top

Tunnel Bottom

Tunnel

Sides

figure 1

Tools Required: Drill & Jigsaw

ver 20120409

Congratulations on your purchase of the Plexidor® Pet Door or

BiteGuard KennelPlex

dog door. It will provide you many years of

service.

Plexidor

Pet Door Wall Kit Instruction for All Sizes Plexidor

: S, M, L, XL page 2

and BiteGuard KennelPlex

1113, 1418, 1419 & 1825 and Plexidor

Electronic LG

Suggested Framing for Size S

Note you do not have to remove the

drywall to insert the cross member.

Cut the hole for the pet door and

insert the cross member through that

hole. Then drive screws through the

drywall and the 2x4’s (2x6’s) at points

A. Then patch the holes

Suggested Framing for Size M

This is the typical installation for

the BG 1113 dog door as well.

Suggested Framing for Size L

Size L fits between studs that

are 16” on center. No framing

is required.

This is also the framing for the

BG 1418 & BG 1419

This is the typical installation for

the LG Plexidor Electronic

pet door as well.

If framing of the hole is required, the best and usually the easiest way to do this is with the

same materials as the framing in your walls, 2x4’s, 2x6’s. etc. You may frame in the top and

bottom of the hole, but it is not required.

Remember to check for and avoid electric wiring and plumbing.

The Size XL and BG KennelPlex

1825do not fit between studs 16 inches on center. If

you are going through a load bearing wall contact a local carpenter or contractor.

figure 2 figure 3 figure 4

ver 20120409

Plexidor

Pet Door Wall Kit Instruction for All Sizes Plexidor

: S, M, L, XL page 3

and BiteGuard KennelPlex

1113, 1418, 1419 & 1825 and Plexidor

Electronic LG

Step #1. Measuring Your Pet.

Measure the height of your pet’s

shoulders. The ideal height is with the

top of the pet door opening 1” to 2”

above the pet’s shoulder blades. The

cat or dog will lift their legs and step

through the opening. Any height that

is comfortable for your pet will work

fine.

If the inside floor level is different than

the outside surface you may need to

build a step or ramp. Or, you may

adjust the height of the hole to a loca-

tion between the two levels. Test with

a piece of cardboard with a hole cut in

it and see if your cat or dog can com-

fortably pass through a hole at that

height. You can only cut a hole once.

Test the height if in doubt.

Step #2. Cutting Holes

Use the template provided to cut

the inside hole. Cut the exterior

hole to the dimensions listed on this

page as the Outside Cut Hole

Measurements.

NOTE

: The inside and outside

holes are different sizes. Line up

the top of both holes to the same

height. The top of the tunnel will

slope up a little. The bottom of the

tunnel will slope down to drain any

water or snow to the outside.

Outside Cut Hole Measurements

Pet Door Size w “ x h”

S 8 3/8 10 1/8

M 11 7/8 15 1/4

L 14 1/2 19

XL 18 1/2 26 1/2

LG Electronic 14 1/2 23 1/2

BiteGuard 1113 11 7/8 15 1/4

BiteGuard 1418 & 1419 14 1/2 19

BiteGuard 1825 18 1/2 26 1/2

Inside Side Cut Hole Measurements

Pet Door Size w “ x h”

S 8 3/8 9

M 11 7/8 14

L 14 1/2 18

XL 18 1/2 26 1/4

LG Electronic 14 1/2 21 1/2

BiteGuard 1113 11 7/8 14

BiteGuard 1418 & 1419 14 1/2 19

BiteGuard 1825 18 1/2 26 1/4

Outside Frame

Inside Frame, Plexidor

Size Height

S 10 1/8”

M 15 1/4”

L 19”

XL 26 1/2”

Size

Height

S 9”

M 14”

L 18”

XL 26 1/4”

Cut Hole

Side View, Figure 5

ver 20120409

LG Electronic 23 1/2”

BiteGuard 1113 15 1/4”

BiteGuard 1418 19”

BiteGuard 1419 19”

BiteGuard 1825 26 1/2”

LG Electronic 21 1/2”

BiteGuard 1113 14”

BiteGuard 1418 19”

BiteGuard 1419 19”

BiteGuard 1825 26 1/4”

Spring

Cover

Step #3 Install Plexidor

Pet Door

Install pet door on the inside surface of

the wall with 4 screws.

View from Outside of House, figure 7Side View, figure 6

Step #4 Temporarily Install the Outside Frame

You can temporarily install the outside frame with

tape. Or you can use 2 flat head screws and screw

through the inside edge of the trim piece.

This will allow you to measure and cut the tunnel

pieces accurately.

Outside Frame

Outside Frame Inside Frame, Plexidor

ver 20120409

Spring

Cover

Plexidor

Pet Door Wall Kit Instruction for All Sizes Plexidor

: S, M, L, XL page 4

and BiteGuard KennelPlex

1113, 1418, 1419 & 1825 and Plexidor

Electronic LG

Step #5 Installing Tunnel Top and Bottom

Hold the top and bottom tunnel pieces in place as shown in figure 8 and mark the outside

edge. Cut the tunnel pieces 1/8 inch shorter than your marks. This will cause the edge of

the tunnel pieces to be just a little in the tunnel. Cut with the provided aluminum jigsaw

blade. Use a file or sand paper on cut edges to smooth them. If you are using metal

snips to cut the aluminum, first cut a rough cut leaving 1/4 inch of material. Then cut a

second time along your cut line. This will give you a smooth and neat finish cut.

Side View, figure 8

Mark here and trim 1/8”

shorter than your marks.

Side View, figure 9

DO NOT DO THE ABOVE

If there is a crack or the metal flexs and

creates a crack at point X, a dog or cat

will get their claw caught and may injure

themselves.

Cut here

Top tunnel piece will rest on small

notch that runs allong top of the

frame of the Plexidor or BiteGuard.

* Size XL and BiteGuard 1418, 1419 & 1825

When installing the bottom piece of the tunnel, if there is a

bottom lock, do not block the movement of the bottom lock

on the dog door.

ver 20120409

Spring

Cover

Plexidor

Pet Door Wall Kit Instruction for All Sizes Plexidor

: S, M, L, XL page 5

and BiteGuard KennelPlex

1113, 1418, 1419 & 1825 and Plexidor

Electronic LG

Tunnel Roof

Back of

springs are not

exposed.

Tunnel roof

blocks dogʼs

access to

springs.

Top and bottom

tunnel pieces lay

inside of the

exterior frame.

Screw the top piece in place with 2 flat head stainless steel screws at points A. Screw the bottom

piece in place with 2 flat head stainless steel screw at points B. See figures 10 and 11.

Side View, figure 10

Outside View, figure 11

ver 20120409

Spring

Cover

Plexidor

Pet Door Wall Kit Instruction for All Sizes Plexidor

: S, M, L, XL page 6

and BiteGuard KennelPlex

1113, 1418, 1419 & 1825 and Plexidor

Electronic LG

Step #7 Install Tunnel Sides

Hold side pieces in place. Mark and cut 1/8” shorter than your marks. At this time remove the temporary screws that are holding

the outside frame if you installed these. Screw in each sheet with 2 stainless steel pan head screws at points C in figure 12 and 13.

If your tunnel is wide, install stainless steel pan head screws at points D. If possible, you may install with the cut edge towards the

inside and the factory cut edge towards the outside. This will give a cleaner look.

Side View, figure 12

Mark here and trim

1/8” shorter than

your marks.

Cut here

Outside View, figure 13

Step #8 Silicone the Joints

Apply silicone between the outside frame and

the tunnel pieces.

Before installing the 2 bottom screws

put silicone in the screw holes.

ver 20120409

Spring

Cover

Plexidor

Pet Door Wall Kit Instruction for All Sizes Plexidor

: S, M, L, XL page 7

and BiteGuard KennelPlex

1113, 1418, 1419 & 1825 and Plexidor

Electronic LG

Practical Installation Tips

GENERAL CHECK LIST

1. Check for Electrical or Plumbing.

2. Cut a test hole.

Cut a test hole in the drywall in the inside of the house that is 6” x 6”. Visually check

inside this test opening to make sure there is no electrical or plumbing. If you find elec-

trical or plumbing at that time, you can patch the test hole with a 6” x 6” piece of drywall.

Some locations you do not want to go through: right next to doors or right next to

windows, because there will be two studs right there, and you do not want to hit those

supporting studs. Mounting under a window works very well.

3. Cutting, Taping and Drilling.

After you have checked to make sure there is no electrical or plumbing, complete cutting

your hole on the inside of the drywall. The next step is to drill a hole in the upper left

hand corner and upper right hand corner at the same height of the hole on the inside.

This marks the location of the top two corners of the outside hole. Then tape off the

inside hole with masking tape and plastic, so you do not get any mess inside the house.

The blue masking tape works best because it will not remove paint or wall paper when

removed. Next, go to the outside and cut the hole where you have your top two drill

marks. This is the hole for the outside frame. If it is a size small or medium Plexidor

this is when you would slip in the 2x4ʼs or 2x6ʼs, or other required framing. You do not

need to frame the top or the bottom, but you need to frame the left and the right. This is

so you have a place to screw in the mounting screws. The size large Plexidor

and

Plexidor

Electronic fit exactly between the studs, so you are not required to put any

framing in at all.

SIZE XL PLEXIDORS

and BiteGuard KennePlex

1825

Extra-Large Plexidor

pet doors and BiteGuard KennePlex

1825 do not fit between

studding. To properly put an these models in a wall, you need to remove a stud, add 2

jack studs, add a double header over the opening, and then install the pet door under-

neath this.

page 8

Notes:

INSTALLATION IN BLOCK WALLS

Block installation are possible. Installers do a lot of block walls. The procedure is

basically the same. Check for electrical and plumbing on the inside. Cut your 6” x 6”

hole through the drywall on the inside and check to see if there are any signs of electri-

cal and plumbing. If you see no signs of electrical and plumbing, then cut out your dry-

wall to the size you need. The next step is to take a hand chisel and score the con-

crete block left, right, top, and bottom all the way around so that you will not have any

spider cracks go into the block that you want to remain. Take the chisel and tap-tap-tap

all the way around the cut line. Drill holes in the upper left-hand corner and upper

right-hand corner. Tape off the hole inside the house with tape and plastic. Then, go

to the outside, and you will have your two holes for your upper left-hand corner and

upper right-hand corner. If there is stucco, score the stucco with a rotary blade. A

Rotozip with a masonry blade works well. You can also use a skil saw with a masonry

blade. Again, scoring that exterior stucco will keep any spider cracks from going into

the stucco or chipping away the painted area around the hole. Now you have scored

the outside area, and can now drill a hole in the middle so that there is a little relief in

pressure when you are breaking this. You can use a hand chisel and chisel it out. Or

you can use a rotary hammer, which is like a small jackhammer, to chisel out the block.

You work from the middle of the hole to the edges. Chip away a little bit in the middle

so you have a place to start, and then work to the outside edges. Again, you have

scored the block on the inside and you have scored the block on the outside. So you

should not get spider cracks going into the block you want to remain. Once the hole is

cut, vacuum up the area and clean it up. Then remove the plastic and tape that is on

the inside of the house. From this point on the installation it is similar to the wall instal-

lation in a stud wall.

ALTERNATIVE METHOD OF ALIGNING HOLE FROM INSIDE TO OUTSIDE

If you think the stucco on the outside of the house will chip when drilling the two top

corner holes, use the following method to mark your hole location: Cut the hole on the

inside of the house. Align one side of the hole next to a stud. Mark the center of the

hole. Drill through the center hole. Then tape off the inside hole with tape and plastic.

Use this center hole to measure off of when cutting the outside hole.

page 9

Notes:

INSTALLATION IN BRICK VENEER WALLS

Mark the outside wall first. You want to make the top of the cut on a mortar line. This

will keep the top of the hole a nice straight line with no partial bricks. Partial bricks on

the top may want to fall out. Do not be concerned with the cut for the bottom of the

hole. Cut through the brick with a masonry gas saw using a diamond blade.

COLD CLIMATE INSULATION OF WALL UNITS

After the wall unit has been installed remove the interior frame. Spray around the tun-

nel with “Great Stuff, Window and Door Foam.” You can find this at building supply

stores and hardware stores. This foam will expand and fill the gaps around the outside

frame from inside the wall. WARNING this stuff sticks to everything. If you think it will

leak on the outside wall because there are gaps there, put blue masking tape on the

outside wall before applying the “Great Stuff Foam.” Spraying this on the aluminum

tunnel pieces also greatly reduces sweating condensation on the tunnel walls in the

winter. This is great stuff.

UNEVEN WALLS

If the exterior wall is uneven, you can use “Great Stuff Foam” to fill the gaps. Tape off

the outside wall area you do not want the foam to stick to. Spray the “Great Stuff” to

fill the gaps. Wait for it to dry. This can take an hour, you may want to return later.

Cut off the extra with a utility knife. The “Great Stuff” will not rot, bugs will not eat it, it

will fill large 1” gaps, and it can be painted.

AREAS OF EXTREME COLD AND/OR NORTH WALLS

If the house is in a really cold area like Minnesota or Alaska, the only good solution

may be to install 2 Plexidors

. One on the inside wall surface and one on the outside

wall surface. This would be 2 Basic Plexidor

units.

If you have installation problems, please contact your

local dealer. They are experienced at installations in

local construction. To find an installer in your area

call Customer Service at 800-749-9609.

page 10

Notes:

page 11

Notes:

If you have installation problems, please contact your local dealer.

They are experienced at installations in local construction.

To find an installer in your area

Call Customer Service at 800-749-9609.

PlexiDor Performance Pet Doors PD WALL SM BR Installation guide

Brand: PlexiDor Performance Pet Doors

Model: PD WALL SM BR

Category: Pet care

Type: Installation guide

This manual is also suitable for

Download PDF

report

PlexiDor Performance Pet Doors PD WALL SM BR Installation guide

This manual is also suitable for

PlexiDor Performance Pet Doors PD WALL SM BR Installation guide

Related papers

Other documents