Harbor Freight Tools 90725 User manual

Brand: Harbor Freight Tools

Model: 90725

Category: Camera kits

Type: User manual

Mini Laser Level with TMini Laser Level with T

Mini Laser Level with T

ripodripod

ripod

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

any artwork contained herein may be reproduced in any shape or form without the express

written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

90725

90725 Laser Level.P65 10/13/03, 9:06 AM1

SKU 90725 Page 2

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly

instructions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be fol-

lowed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use this tool in damp or wet

locations. Don’t expose to rain. Keep work area well lighted. Do not use in

the presence of flammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

4. Store idle equipment. When not in use, tool must be stored in a dry location

to inhibit rust. Always lock up tool and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. There are certain

applications for which this tool was designed. It will do the job better

and more safely at the rate for which it was intended. Do not modify this

tool and do not use this tool for a purpose for which it was not intended.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught

in moving parts. Protective, electrically non-conductive clothes and non-skid

footwear are recommended when working. Wear restrictive hair covering to

contain long hair.

Material: All ABS body with

aluminum end fittings

Tripod: Aluminum swivel head

zinc plated legs

Lockable swivel head

Adjustability: 360 degrees

Features: On/Off switch

Power: (3) 1.5v AG13 button

cell batteries included

Dimensions: 7-5/8”l x 1”w x 2-1/8”h

Levels: (3) Liquid filled vials:

Horizontal, Vertical, and

45 degree

Working Range: Approx. 36’

Laser Dot: 1/4” OD @ approx. 36’

350 nm wavelength

F.D.A. certification number 0310895-00

Laser Class II

90725 Laser Level.P65 10/13/03, 9:06 AM2

SKU 90725 Page 3

7. Use eye and ear protection. Always wear ANSI approved impact safety

goggles. Wear a full face shield if you are producing metal filings or wood

chips. Wear an ANSI approved dust mask or respirator when working around

metal, wood, and chemical dusts and mists.

8. Do not overreach. Keep proper footing and balance at all times. Do not

reach over or across running machines.

9. Maintain tools with care. Keep clean for better and safer performance.

Follow instructions for batteries and changing accessories. The handles

must be kept clean, dry, and free from oil and grease at all times.

10. Maintain Batteries. Remove batteries when not in use for a prolonged

period of time to prevent corrosion and damage to this tool.

11. Avoid unintentional starting. Be sure the switch is in the Off position

when not in use.

12. Stay alert. Watch what you are doing, use common sense. Do not operate

any tool when you are tired.

13. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate

properly and perform its intended function. Check for alignment and binding

of moving parts; any broken parts or mounting fixtures; and any other

condition that may affect proper operation. Any part that is damaged should

be properly repaired or replaced by a qualified technician. Do not use the tool

if any switch does not turn On and Off properly.

14. Guard against electric shock. Prevent body contact with grounded

surfaces such as pipes, radiators, ranges, and refrigerator enclosures.

15. Replacement parts and accessories. When servicing, use only

identical replacement parts. Use of any other parts will void the warranty.

Only use accessories intended for use with this tool. Approved accessories

are available from Harbor Freight Tools.

16. Do not operate tool if under the influence of alcohol or drugs.

Read warning labels on prescriptions to determine if your judgment or

reflexes are impaired while taking drugs. If there is any doubt, do not

operate the tool.

17. Maintenance. For your safety, service and maintenance should be

performed regularly by a qualified technician.

90725 Laser Level.P65 10/13/03, 9:06 AM3

SKU 90725 Page 4

18. Be Eye Aware. Laser light can potentially harm the eye. WARNING: Do not

look directly into this laser, or the reflection of the light. Do not allow any other

person or animal to be exposed to the direct or reflected laser beam.

Warning: The warnings, cautions, and instructions discussed in

this instruction manual cannot cover all possible conditions and

situations that may occur. It must be understood by the operator

that common sense and caution are factors which cannot be built

into this product, but must be supplied by the operator.

Unpacking

When unpacking, check to make sure the following parts are included.

(1) Mini laser level

(1) Tripod

(3) 1.5V AG13 button cell batteries

(1) Instruction booklet

If any parts are missing or broken, please call Harbor Freight Tools at the number

on the cover of this manual.

Assembly

1. To install batteries, unscrew the On/Off switch assembly, and insert three (3)

1.5v batteries (included). Be sure to install the batteries matching the polarity

marked in the battery compartment.

2. This level may be used with or without the tripod. To install or remove the

tripod, thread the tripod stud located on the tripod head into the bottom of

the level. The tripod swivels 360 degrees, and may be tilted at up to 90

degrees vertical. If using the tripod, adjust it as desired, and lock the level

into place using the thumb screw located on the tripod head.

3. The tripod legs may be extended and locked into place to provide greater

working height or to compensate for an uneven surface.

90725 Laser Level.P65 10/13/03, 9:06 AM4

SKU 90725 Page 5

Operation

WARNING: Never allow the laser light or its reflection to shine

directly into the eyes of any person or animal.

Severe eye injury may result.

1. Determine the intended use of the level, and optionally install the tripod,

if it will be needed.

2. Align the laser level as required, observing the vertical, horizontal or 45

degree spirit levels. These will indicate the relative position of the laser

level to actual level.

3. When the laser level is correctly positioned, turn on the laser by depress-

ing the On/Off switch at the end of the level. Recheck the spirit levels to

be sure the laser level has not been moved.

4. Mark the desired measurement, then turn the laser off by depressing the

On/Off switch.

Using the level to equalize height of distant components: For

example: If you wish to install cement footings for a storage shed, first determine

the desired height of any one of the footings. Align the laser beam with the top

surface of the reference footing, and assure that the liquid level on top of the laser

level is at level with the ground. Now direct the laser beam toward each of the

remaining footing locations. On reference stakes at those locations, mark the spot

that the laser illuminates. This indicates the desired top surface of that footing.

This technique can be used for many similar applications, for example to align

pictures on a wall.

Using the level to install horizontal or vertical components: For

example: To install a chair rail on an interior wall, first mark the desired height of

the rail. Align the laser level with that point, and assure that the liquid level

indicates level with the floor. Shine the laser light on the adjoining wall, and have

an assistant mark that location. Now install the chair rail in a direct line between

the two points. This same technique can be used to install vertical or 45 degree

angle components.

Using the level to check slope: For example: To determine the slope

of a floor, place the laser level at one end of the floor, using the tripod. Assure that

the laser is level to the ground by observing the liquid level on the top. Measure

the vertical drop from the laser lens to the floor surface. Shine the laser light on a

ruler held vertical at the other end of the floor. The difference in these measure-

ments is the amount of slope in the floor. This technique can also be used to

design slope, such as when constructing an outdoor surface which will require a

run-off slope.

Your laser level is a versatile tool. The above suggestions are only a few

of the many uses you will discover for this tool.

90725 Laser Level.P65 10/13/03, 9:06 AM5

SKU 90725 Page 6

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER

NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO

THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE

PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE

PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THat ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN

BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER

ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS

OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Maintenance

1. Remove the batteries when the laser level will not be used for an extended

period of time.

2. Prevent sharp impacts to the tool, such as dropping it or allowing it to bang

around in a tool box.

3. Keep the laser level clean and dry. Wipe any dirt, moisture or grease from it

whenever necessary. Store it safely in a clean, dry place.

Parts List

1. 45 degree liquid level 4. On/Off switch

2. Horizontal liquid level 5. Mini tripod (one leg hidden)

3. Vertical liquid level 6. Laser lens

Assembly Drawing

NOTE: Some parts are listed and shown for illustration purposes only and are not

available individually as replacement parts.

90725 Laser Level.P65 10/13/03, 9:06 AM6

Harbor Freight Tools 90725 User manual

Brand: Harbor Freight Tools

Model: 90725

Category: Camera kits

Type: User manual

Download PDF

report

Harbor Freight Tools 90725 User manual

Harbor Freight Tools 90725 User manual

Related papers

Other documents