Amana DGK1B Installation guide

Amana
Brand
Amana
Model
DGK1B
Type
Installation guide

This manual is also suitable for

Amana DGK1B is a condenser baffle kit designed to prevent recirculation of hot condenser air in package terminal units. It is compatible with outdoor grilles having horizontal louvers. The kit includes baffles, screws, shoulder washers, and a gasket. Installation involves locating the baffles on the condenser coil flange, positioning the louvers to direct air towards the center, and securing the grille to the condenser flange with the provided hardware.

Amana DGK1B is a condenser baffle kit designed to prevent recirculation of hot condenser air in package terminal units. It is compatible with outdoor grilles having horizontal louvers. The kit includes baffles, screws, shoulder washers, and a gasket. Installation involves locating the baffles on the condenser coil flange, positioning the louvers to direct air towards the center, and securing the grille to the condenser flange with the provided hardware.

Installation Instructions
PTAC Condenser
Baffle Kit
October 2000
Rev. 2
A3495903
Description
The condenser baffle kit is required when replacing an ex-
isting package terminal unit and the original outdoor grille
is not made by the same manufacturer. These baffles are
required to deflect discharge air away from the inlet, pre-
venting recirculation of hot condenser air.
This kit is intended to be used with outdoor grilles having
horizontal louvers. If the outdoor grille has vertical louvers,
contact the manufacturer of the package terminal unit be-
ing installed.
NOTE: This kit is
not
to be used when the outdoor grille is
provided by the original manufacturer of the package ter-
minal unit.
CAUTION
To prevent damage to the unit due to
restricted air flow, remove any baffles
or deflectors of any kind from the out-
door grille.
Tools Required
1/4 Inch Electric Drill
1/8 Inch Diameter Drill Bit
Center Punch and Hammer
6 Foot Rule
Combination Square
1/4 Inch Nut Driver or Socket
Installation
1. Locate the baffles on the condenser coil flange as
shown in Figure 1. Position the louvers to direct the
air toward the center as the air leaves the coil.
Basepan
Condenser
Condenser Baffles
Figure 1
2. Using the screws and shoulder washers provided, se-
cure the grille to the condenser flange. NOTE: Be sure
to install the gasket between the grille and the flange
as shown in Figure 2.
BAFFLE
GASKET
SHOULDER
WASHER
SCREW
CONDENSER
FLANGE
Figure 2
RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.
ATTENTION INSTALLING PERSONNEL
As a professional installer you have an
obligation to know the product better than the
customer. This includes all safety
precautions and related items.
Prior to actual installation, thoroughly
familiarize yourself with this Instruction
Manual. Pay special attention to all safety
warnings. Often during installation or repair
it is possible to place yourself in a position
which is more hazardous than when the unit
is in operation.
Remember, it is your responsibility to install
the product safely and to know it well enough
to be able to instruct a customer in its safe
use.
Safety is a matter of common sense...a matter
of thinking before acting. Most dealers have
a list of specific good safety practices...follow
them.
The precautions listed in this Installation
Manual are intended as supplemental to
existing practices. However, if there is a
direct conflict between existing practices and
the content of this manual, the precautions
listed here take precedence.
Made in USA
  • Page 1 1

Amana DGK1B Installation guide

Amana
Brand
Amana
Model
DGK1B
Type
Installation guide
This manual is also suitable for

Amana DGK1B is a condenser baffle kit designed to prevent recirculation of hot condenser air in package terminal units. It is compatible with outdoor grilles having horizontal louvers. The kit includes baffles, screws, shoulder washers, and a gasket. Installation involves locating the baffles on the condenser coil flange, positioning the louvers to direct air towards the center, and securing the grille to the condenser flange with the provided hardware.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents