Geovision GV-Control Center System User manual

GV-Control Center System

UseUser’s Manual

CCS-UM-A

Under the copyright laws, this manual may not be copied, in whole or in part,

without the written consent of GeoVision.

Every effort has been made to ensure that the information in this manual is

accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind

and assumes no responsibility for errors or omissions. No liability is assumed

for incidental or consequential damages arising from the use of the information

or products contained herein. Features and specifications are subject to

change without notice.

Note: No memory card slot or local storage function for Argentina.

GeoVision, Inc.

9F, No. 246, Sec. 1, Neihu Rd.,

Neihu District, Taipei, Taiwan

Tel: +886-2-8797-8377

Fax: +886-2-8797-8335

http://www

.geovision.com.tw

Trademarks used in this manual: GeoVision, the GeoVision logo and GV

series products are trademarks of GeoVision, Inc. Windows is the registered

trademark of Microsoft Corporation.

February 2021

i

Welcome to the GV-Control Center System User’s Manual.

The Manual provides an overview of the GV-Control Center System and its

accessories. It also includes the instructions to guide you through the installation and

use of the GV-Control Center System:

 Chapter 1, Introduction

Identifies the accessories and options of the GV-Control Center System.

 Chapter 2, Overview

Identifies the components of the GV-Control Center System.

 Chapter 3, Getting Started

Provides step-by-step instructions on setting up the GV-Control Center System.

 Chapter 4, Troubleshooting

Suggests courses of action if the GV-Control Center System doesn’t seem to be

working properly.

User’s Manual for

GV-Control Center System

ii

Contents

Safety Instructions.................................................................................................. iii

Chapter 1 Introduction........................................................................................... 1

1.1 Packing List .................................................................................................1

1.2 Options........................................................................................................1

Chapter 2 Overview ............................................................................................... 2

2.1 Front View....................................................................................................2

2.2 Rear View....................................................................................................3

Chapter 3 Getting Started...................................................................................... 4

3.1 Basic Installation..........................................................................................4

3.2 Installing the Hard Drive...............................................................................5

3.3 Turning on the Power...................................................................................7

3.4 Windows Setup Installation..........................................................................8

3.5 Formatting the Hard Drive..........................................................................10

3.6 Configuring the IP Address........................................................................14

3.7 Multi Monitors Application..........................................................................16

3.7.1 Monitor Arrangement...............................................................................16

3.7.2 Matrix View..............................................................................................17

3.7.3 Video Wall................................................................................................17

3.8 System Restoration....................................................................................18

3.9 Updating GV-Control Center System.........................................................19

Chapter 4 Troubleshooting................................................................................. 20

iii

Safety Instructions

Observe these safety instructions to help ensure against injury to yourself and damage

to the product.

 Read all safety and installation instructions before you operate the product.

 Do not operate the product in high humidity areas or expose it to water or moisture.

 Do not put the product in an unstable, a slanting or vibrated place.

 Do not block any ventilation opening.

 Do not install the product near any heat sources such as radiator, heat register or

other apparatus that produce heat.

 Operate the product using only the type of power source indicated on the marking label.

 If you are in an area with unstable voltage, make sure to install an automatic voltage

regulator (AVR) or a UPS power supply with AVR function, to maintain a constant

voltage.

 All damages to the power supply caused by unstable voltage are not included in the

2-year warranty service.

 Do not defeat the safety purpose of the grounding-type plug. A grounding plug has two

blades and a third grounding prong. The third prong is provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

 Do not overload wall outlets or extension cords, as this may cause fire or electric

shock.

 Do not use the product when abnormality occurs, such as emitting smoke from the

product, smelling burning, being damaged by drop, invasion of foreign objects inside the

product, etc. Be always sure to remove the AC adaptor at once and contact your dealer.

 Do not use accessories or attachments not recommended by the manufacturer, as they

may cause hazards and void the warranty.

 Do not attempt to service the product yourself, as removing the casing may expose

you to dangerous voltage and void the warranty.

1

Chapter 1 Introduction

1.1 Packing List

The GV-Control Center System package includes the following items. If any of the items are

missing or damaged, contact your dealer to arrange a replacement.

Important: Please keep the original carton and all packing materials for future shipping need.

1. GV-Control Center System

2. Power Cord (by region)

3. Screw Kit

4. Download Guide

5. Warranty Card

1.2 Options

Optional devices can expand your GV-Control Center System’s capabilities and versatility.

GV-IO Box Series

GV-IO Box series provides 4 / 8 / 16 inputs and relay outputs and

support both DC and AC output voltages, with optional support for

Ethernet module and 4E additionally supporting PoE connection.

GV-Joystick V2

GV-Joystick V2 facilitates PTZ camera control. It can be either

plugged into the GeoVision surveillance system for independent use

or connected to GV-Keyboard to empower the operation.

GV-Keyboard V3

GV-Keyboard V3 is designed to program and operate the GeoVision

surveillance system, and can be connected with PTZ cameras

directly for PTZ control.

Overview

2

Chapter 2 Overview

2.1 Front View

4

5

1

2

3

Figure 2-1

No. Name No. Name

1 Power Button 4 HDD LED

2 Reset Button 5 USB 3.1 Gen 1 (Type-A) x 2

3 Power LED

3

2.2 Rear View

Figure 2-2

No. Name No. Name

1 Power Connector 11 DisplayPort 1.4 (up to 4096 x 2160 / 60Hz)

2 PS/2 x 1 12 Gigabit Ethernet

3 Gigabit Ethernet 13 DisplayPort 1.4 (up to 4096 x 2160 / 60Hz)

4

DisplayPort (up to 4096 x 2304 /

60Hz)

14

Audio Jack x 3

 Line In (Blue)

 Line Out / Front Speaker Out (Green)

 Mic In (Pink)

5 D-Sub (up to 1920 x 1200 / 60Hz) 15 USB 3.1 Gen 2 (Type-A) x 2

6 Not functional 16 USB Type C

7

HDMI 2.0b (up to 3840 x 2160 /

60Hz)

17

HDMI 1.4b (up to 4096 x 2160 / 24Hz or

2560 x 1600 / 60Hz)

8 DVI-D (up to 2560 x 1600 / 60Hz) 18 USB 3.1 Gen 1 (Type-A) x 2

9

HDMI 2.0b (up to 3840 x 2160 /

60Hz)

19 USB 2.0/1.1 x 2

10 DVI-D (up to 2560 x 1600 / 60Hz)

Getting Started

4

3

Chapter 3 Getting Started

3.1 Basic Installation

This section describes all the equipment required to program and operate the GV-Control

Center System.

Figure 3-1

1. Using the supplied power cord, connect one end to the AC input and the other end to the

power outlet.

2. Connect the mouse and keyboard to the USB or PS/2 port.

3. Using the RJ-45 cable, connect one end to the Ethernet port and the other end to Network.

4. Using the D-Sub / HDMI / DVI-D / DisplayPort cable supplied by the monitor manufacturer,

connect up to 9 monitors for simultaneous displays.

Once the above hardware is properly connected, press the Power button on the front panel to

start the system. It takes about 1 minute for startup.

5

3.2 Installing the Hard Drive

1. Unscrew the four screws on the top and two screws on each side of the system (a total of

8 screws). Pull out the motherboard tray.

 

Figure 3-2

2. Unscrew the set screw on the hard drive bracket located at the right side of the fans.

Remove the hard drive bracket by pushing it to the left.

Figure 3-3

3. Place the hard drive onto the hard drive bracket. Align and tighten all four screws on the

side to secure the hard drive.



Figure 3-4

Getting Started

6

3

4. Repeat step 3 to install another hard drive onto the hard drive bracket.

5. Push to lock the hard drive bracket back to its original position on the motherboard tray.

Tighten the set screw to secure the hard drive bracket.

 

Figure 3-5

6. Connect the hard drives to the motherboard using the SATA and power cables.

7. Push the motherboard tray back into the system case. Align and tighten the screws on the

top and both sides of the system.

Tips:

1. In Step 3, begin by installing a hard drive onto the bottom of the hard drive bracket.

Leave one side of the screws partially tightened to make it easier to align the second

hard drive on top.

2. In Step 6, begin by connecting the SATA and power cable to the hard drive on the

bottom of the hard drive bracket.

7

3.3 Turning on the Power

To turn on the power, follow these steps:

1. Turn on the monitor.

Power On

Figure 3-6

2. Turn on the main power switch on the front panel.

Figure 3-7

The GV-Control System will run a series of self-tests, and later series of messages may be

displayed as the various hardware and software subsystems are activated.

Note: The series of self-tests will take around 20 seconds to 2 minutes, depending on the

number of installed hard drives.

Getting Started

8

3

3.4 Windows Setup Installation

The Windows setup is preparing your computer for first use.

1. After the Windows starts, this setup screen appears. Select your language and click Next

to continue.

Figure 3-8

2. Select your regional settings and time zone and click Next to continue.

Figure 3-9

9

3. Click Accept to accept Microsoft software license terms.

4. Select between “Customize” and “Use Express settings” for your Windows 10 installation.

5. Type your account name. It is recommended that you create a password for your account

and click Next.

Figure 3-10

6. When the above setup process is complete, Windows will finalize your settings

automatically in the background and restart.

Getting Started

10

3

3.5 Formatting the Hard Drive

Be sure to install each of your hard drives separately for formatting. Do not install and format

more than one hard drive at a time.

To format a hard disk, follow the steps below:

1. Right-click the Computer icon

on your desktop, select Manage, and select Disk

Management when the Computer Management window appears.

2. On the main page of Disk Management, the Initialize Disk dialog box appears for the new

drive. Click the created disk and select a partition style.

Figure 3-11

3. Click OK. The created disk is successfully initialized.

4. On the main page of Disk Management, right-click in the unallocated space of a new drive

and select New Simple Volume.

Figure 3-12

11

5. The New Simple Volume Wizard appears. Click Next to continue.

Figure 3-13

6. The default partition size is the same as the maximum disk space. Make changes if

necessary. Click Next to continue.

Figure 3-14

Getting Started

12

3

7. Assign a drive path that is not in use by other devices, and click Next to continue.

Figure 3-15

Note: The default drive path starts from D:\.

8. Type a name in the Volume label box, ex. HDD1, and click Next to continue.

Figure 3-16

13

9. When the formatting is complete, click Finish to close the wizard.

Figure 3-17

10. When the drive is successfully initialized, partitioned, and formatted, its status description

should display “Healthy.”

Figure 3-18

Getting Started

14

3

3.6 Configuring the IP Address

The GV-Control Center System supports remote monitoring, control and configuration over a

network connection.

The system supports up to 2 Ethernet ports.

Figure 3-19

To change the static IP addresses or to enable dynamic IP address, follow the steps below.

1. Right-click the Network Connection icon

from the notification area and select Open

Network and Sharing Center.

Figure 3-20

2. Click Change Adapter Settings from the left-hand side menu of the Network and Sharing

Centre window.

3. Under Network Connections, select a network connection you want to configure its IP

address.

Figure 3-21

15

4. Select Internet Protocol Version 4 (TCP/IPv4) and then click Properties.

Figure 3-22

5. Select Use the following IP address and type the new IP information in the fields or

select Obtain an IP address automatically to enable dynamic IP address.

Figure 3-23

6. Click OK to finish the setting.

Page is loading ...

Geovision GV-Control Center System User manual

Geovision GV-Control Center System User manual

Related papers