Rinnai REB-A1800FF-US Installation guide

●

H167-0771-1X01(00)

2 Rinnai I-Series Condensing Boiler Combi Manual

1. Welcome ................................................................................................................................................... 4

2. Safety ........................................................................................................................................................ 5

2.1 Safety Symbols ................................................................................................................................................. 5

2.2 Safety Precauons ........................................................................................................................................... 5

3. About the Boiler......................................................................................................................................... 7

3.1 Front View ....................................................................................................................................................... 7

3.2 Boom View .................................................................................................................................................... 7

3.3 Components .................................................................................................................................................... 9

3.4 Specicaons ................................................................................................................................................. 10

3.5 Dimensions .................................................................................................................................................... 11

3.6 Accessories .................................................................................................................................................... 13

4. Installaon .............................................................................................................................................. 14

4.1 Installaon Guidelines ................................................................................................................................... 14

4.2 What You’ll Need ........................................................................................................................................... 15

4.3 Items Included ............................................................................................................................................... 16

4.4 Choose an Installaon Locaon..................................................................................................................... 17

4.5 Mount the Boiler to the Wall ........................................................................................................................ 19

4.6 Fill the Condensate Collector ........................................................................................................................ 20

5. Venng .................................................................................................................................................... 21

5.1 Guidelines ...................................................................................................................................................... 21

5.2 Venng Installaon Sequence ....................................................................................................................... 22

5.3 Terminaon Consideraons .......................................................................................................................... 22

5.4 PVC Venng Safety Switch ............................................................................................................................. 23

5.5 Venng Opons ............................................................................................................................................. 25

6. Gas Supply ............................................................................................................................................... 46

6.1 Connect the Gas Supply ................................................................................................................................. 46

6.2 Gas Operang Instrucons ............................................................................................................................ 47

6.3 Gas Pipe Sizing Reference Tables .................................................................................................................. 48

7. DHW System Piping .................................................................................................................................. 50

7.1 Guidelines ...................................................................................................................................................... 50

7.2 Instrucons .................................................................................................................................................... 50

7.3 Piping Diagram for a Basic DHW Installaon ................................................................................................. 51

8. CH System Piping ..................................................................................................................................... 52

8.1 Guidelines ...................................................................................................................................................... 52

8.2 Instrucons .................................................................................................................................................... 52

8.3 Common CH Components ............................................................................................................................. 53

8.4 Piping Diagram for a Basic CH System (With Hydraulic Separaon) ............................................................. 56

8.5 Hydraulic Separaon ..................................................................................................................................... 57

8.6 Connect the Pressure Relief Valves (DHW and CH) ....................................................................................... 59

8.7 Connect the Condensate Drain Line .............................................................................................................. 60

8.8 Condensate Pump Safety Switch Wiring ....................................................................................................... 61

If the informaon in these instrucons are not followed exactly, a re or explosion may

result causing property damage, personal injury, or loss of life.

• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS

− Do not try to light any appliance.

− Do not touch any electrical switch; do not use any phone in your building.

− Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instrucons.

− If you cannot reach your gas supplier, call the re department.

• Installaon and service must be performed by a qualied installer, service agency or the gas supplier.

WARNING

Rinnai I-Series Condensing Boiler Combi Manual 3

9. Power Supply ........................................................................................................................................... 63

9.1 Guidelines ...................................................................................................................................................... 63

9.2 Electrical Connecons ................................................................................................................................... 64

9.3 Post-Power Supply Connecon Checklist ...................................................................................................... 64

10. Commissioning ....................................................................................................................................... 65

10.1 Safety Precauons ....................................................................................................................................... 65

10.2 Filling Process .............................................................................................................................................. 65

10.3 Deaeraon Process ...................................................................................................................................... 66

11. Post-Installaon Checklist ...................................................................................................................... 68

12. Operaon .............................................................................................................................................. 70

12.1 Start-Up Informaon ................................................................................................................................... 70

12.2 Control Panel ............................................................................................................................................... 71

12.3 Basic Operaon Sengs .............................................................................................................................. 73

12.4 Parameter Sengs ...................................................................................................................................... 84

12.5 Outdoor Reset Control ................................................................................................................................ 89

12.6 DHW Recirculaon Funcon ....................................................................................................................... 94

12.7 Simultaneous CH and DHW Operaon ........................................................................................................ 99

12.8 Diagnosc Codes ....................................................................................................................................... 100

12.9 Forced Hi/Low Fire Modes ........................................................................................................................ 105

13. Maintenance ........................................................................................................................................ 106

13.1 Owner Maintenance .................................................................................................................................. 106

13.2 Licensed Professional Maintenance .......................................................................................................... 107

13.3 Test the Ignion Safety Shut O Device .................................................................................................... 110

14. Appendices .......................................................................................................................................... 111

14.1 Approved Cleaners, Inhibitors and Anfreezes ........................................................................................ 111

14.2 Flush the CH Plumbing System ................................................................................................................. 112

14.3 Flush the DHW Heat Exchanger ................................................................................................................ 113

14.4 System Applicaon Examples ................................................................................................................... 114

14.5 Gas Conversion .......................................................................................................................................... 120

14.6 Wiring Diagram .......................................................................................................................................... 124

14.7 Ladder Diagram ......................................................................................................................................... 125

14.8 CH Pressure Drop and Flow Curve ............................................................................................................ 126

14.9 DHW Pressure Drop and Flow Curve ........................................................................................................ 127

14.10 Guidelines for Addional DHW Controller (Oponal) ............................................................................. 128

14.11 Remove a Boiler from a Common Vent System ...................................................................................... 130

14.12 Massachuses State Gas Regulaons ..................................................................................................... 131

14.13 Warranty .................................................................................................................................................. 132

4 Rinnai I-Series Condensing Boiler Combi Manual

Thank you for purchasing a Rinnai Condensing

Boiler. Before installing and operang this

boiler, be sure to read these instrucons

completely and carefully to familiarize

yourself with the boiler’s features and

funconality.

• You must read the enre manual to

properly operate the boiler.

• Keep this manual for future reference.

• As when using any appliance generang

heat, there are certain safety precauons

you should follow. See secon “2.2 Safety

Precauons” for detailed safety

precauons.

• Be sure your boiler is installed by a

licensed installer.

• If installing in the state of Massachuses,

read secon “14.12 Massachuses State

Gas Regulaons” in this manual.

ANSI

American Naonal Standards

Instute

Btu Brish Thermal Unit

CH Central Heang

DHW Domesc Hot Water

GPM Gallons per minute

LP Liquid Propane

LWCO Low Water Cut O

NG Natural Gas

PP Polypropylene

PRV Pressure Relief Valve

PSI Pounds per square inch

W.C. Inches water column

For Your Records

Dealer Name:

Located on le

side of unit

1

• A trained and qualied professional

must install the boiler, inspect it, and

leak test it before use. The warranty

will be voided due to any improper

installaon.

• The trained and qualied professional

should have skills such as:

− Gas line sizing

− Connecng gas lines, water lines,

valves, and electricity

− Knowledge of applicable naonal,

state, and local codes

− Installing venng through a wall

or roof

− Training in installaon of

condensing boilers. Training on

Rinnai I-Series Condensing Boilers

is accessible at

www.trainingevents.rinnai.us.

• Read all instrucons in this manual

before installing the boiler. The boiler

must be installed according to the

exact instrucons in this manual.

• Proper installaon is the responsibility

of the installer.

• When installaon is complete, leave

this manual with the boiler or give the

manual directly to the consumer.

Following is a list of common acronyms and

abbreviaons used in this manual:

Dealer Phone:

Purchase Date:

Serial #:

Rinnai I-Series Condensing Boiler Combi Manual 5

Indicates an imminently hazardous

situaon which, if not avoided, will

result in personal injury or death.

Indicates a potenally hazardous

situaon which, if not avoided, could

result in personal injury or death.

Indicates a potenally hazardous situaon

which, if not avoided, could result in minor

or moderate injury. It may also be used to

alert against unsafe pracces.

DANGER

WARNING

This manual contains the following important

safety symbols. Always read and obey all

safety messages.

The following precauons apply to the

installer and consumer. Read and follow all

instrucons in this secon.

• Before operang, smell all around the

appliance area for gas. Be sure to smell

next to the oor because some gas is

heavier than air and will sele on the

oor.

• Keep the area around the appliance

clear and free from combusble

materials, gasoline, and other

ammable vapors and liquids.

• Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

• Combusble construcon refers to

adjacent walls and ceiling and should

not be confused with combusble or

ammable products and materials.

Combusble and/or ammable

products and materials should never be

stored in the vicinity of this or any gas

appliance.

• Always check the water temperature

before entering a shower or bath.

2

• If the informaon in these instrucons

is not followed exactly, a re or

explosion may result causing property

damage, personal injury, or death.

• Do not store or use gasoline or other

ammable vapors and liquids in the

vicinity of this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS:

− Do not try to light any appliance.

− Do not touch any electrical

switch; do not use any phone in

your building.

− Immediately call your gas

supplier from a neighbor’s

phone. Follow the gas supplier’s

instrucons.

− If you cannot reach your gas

supplier, call the re department.

• Installaon and service must be

performed by a qualied installer,

service agency or the gas supplier.

• The warning signs in this manual are

here to prevent injury to you and

others. Please follow them explicitly.

Safety alert symbol. Alerts you

to potenal hazards that can

kill or hurt you and others.

WARNING

CAUTION

6 Rinnai I-Series Condensing Boiler Combi Manual

• Flammable liquids such as cleaning

solvents, aerosols, paint thinners,

adhesives, gasoline and propane must be

handled and stored with extreme care.

These ammable liquids emit ammable

vapors and when exposed to an ignion

source can result in a re hazard or

explosion. Flammable liquids should not be

used or stored in the vicinity of this or any

other gas appliance.

• DO NOT operate the boiler without the

front panel installed. The front panel

should only be removed for service/

maintenance or replacing internal

components.

• BURN HAZARD. Hot exhaust and vent may

cause serious burns. Keep away from the

boiler. Keep small children and animals

away from the boiler.

• Heang supply, return and domesc hot

water outlet pipes leaving the boiler can be

hot to touch.

• Install the vent system per local and

naonal codes.

• Do not install this boiler above 10,200 

(3,109 m).

• Do not obstruct combuson air to the

boiler.

• Rinnai recommends that every home have

a carbon monoxide (CO) alarm in the

hallway near bedrooms in each sleeping

area. Check baeries monthly and replace

them annually.

• Do not use this appliance if any part has

been under water. Immediately call a

licensed professional to inspect the

appliance and replace any part of the

control system and any manual gas control

valve which has been under water.

• Do not use substute materials. Use only

parts cered for the appliance.

• Should overheang occur or the gas

supply fail to shut o, turn o the manual

gas control valve to the appliance.

• It is strongly recommended that you use a

trained and qualied professional who has

aended a Rinnai installaon training class

to adjust parameter sengs.

• Do not use an extension cord or adapter

plug with this appliance.

• Any alteraon to the appliance or its

controls can be dangerous and will void

the warranty.

• To protect yourself from harm, before

performing maintenance:

− Turn o the electrical power supply by

unplugging the power cord or by

turning o the electricity at the circuit

breaker. (The boiler controller does

not control the electrical power.)

− Turn o the gas at the gas control,

usually located immediately below the

boiler.

− Turn o the incoming water supply.

This can be done at the isolaon valve

immediately below the boiler for the

domesc hot water. Turning o the

water for the central heang system is

done at the boiler system lling staon

shut-o valve or the main water

supply to the building.

− Use only your hand to turn the manual

gas control valve. Never use tools. If

the manual gas control valve will not

turn by hand, do not try to repair it;

call a trained and qualied

professional. Force or aempted

repair may result in a re or explosion.

• Proper venng is required for the safe

operaon of this appliance. Failure to

properly vent this appliance can result in

death, personal injury and/or property

damage.

Rinnai I-Series Condensing Boiler Combi Manual 7

The I-Series Condensing Boiler is a wall-

mounted, gas-red boiler designed to

providing heang and domesc hot water.

For complete boiler informaon, refer to

the “Rinnai I-Series Condensing Boiler

Installaon Manual” supplied with the

boiler, or visit rinnai.us.

Topics in this secon

• Front View

• Boom View

• Components

• Specicaons

• Dimensions

• Accessories

3

DHW

Hot Outlet

Central

Heang

Supply

Central

Heang

Return

Vent

Connecons

Piping

Connecons

Controller

Gas

DHW

Cold Inlet

Condensate

Drain

8 Rinnai I-Series Condensing Boiler Combi Manual

All items are eld-supplied unless otherwise noted.

Supply to CH System Domesc Cold Water

Return from CH System Gas

Primary-Secondary Heang Kit CH Return

CH Pressure Relief Valve (supplied with boiler) Domesc Hot Water Pressure Relief Valve

CH Supply Central Heang Pressure Gauge

Condensate Drain Gas Shut O Valve

Domesc Hot Water

Rinnai I-Series Condensing Boiler Combi Manual 9

Exhaust Intake

Air Inlet Filter

Fan with Integrated Venturi

Gas Valve

Heat Exchanger

Silencer

Pressure Sensor

Integrated Pump

Diverter Valve

Burner Assembly

Ignion Unit

PC Board Cover

Control Panel

Air Intake

Flue Gas Exhaust

Flow Sensor

Air Vent

PC Board Removed

Plate Heat Exchanger

Water Flow Servo Valve

Bypass Servo Valve

Condensate Trap

Combuson

Test Port

10 Rinnai I-Series Condensing Boiler Combi Manual

1

Maximum gas supply pressure must not exceed the value specied by the manufacturer.

Rinnai products are connually being updated and improved; therefore, specicaons are subject to change

without prior noce.

Model i060C i090C i120C

Dimensions - w, h, d 18.5 in. x 26.4 in. x 11.45 in. (471 mm x 671mm x 290 mm)

Weight 73.0 lb (33 kg) 76.1 lb (34.5 kg)

Appliance Type Wall-Mounted, Gas-Fired Combi Boiler

Installaon Type Indoor

Ignion System Direct Electronic Ignion

Heat Exchanger Surface Area 9.3 sq  10.9 sq 

Gas

Consumpon

(Btu/hr)

Minimum 15,000

Maximum (CH) 60,000 90,000 120,000

Maximum (DHW) 160,000 199,000

DHW

Specicaon

Minimum Acvaon Flow Rate 0.4 GPM (1.5 L/min)

Minimum Operaon Flow Rate 0.26 GPM (1.0 L/min)

Maximum Flow Rate 7.9 GPM (30 L/min) 9.8 GPM (37 L/min)

Flow Rate at 70°F (39°C) rise 4.1 GPM (15 L/min) 5.1 GPM (19 L/min)

Temperature

Seng

CH (Minimum - Maximum) 86°F - 180°F (30°C - 82°C)

DHW (Minimum - Maximum) 98°F - 140°F (37°C - 60°C)

Water

Content

CH 0.75 gal 0.75 gal 0.88 gal

DHW 0.05 gal 0.05 gal 0.05 gal

Water

Pressure

CH

Minimum: 13 PSI (90 kPa) Maximum: 45 PSI (310 kPa)

Recommended: 17-26 PSI (117-180 kPa)

Pressure Relief Valve for CH

(included with system)

30 PSI (207 kPa)

DHW

Minimum: 20 PSI (138 kPa)/Maximum: 150 PSI (1,034 kPa)

(Recommend 30-80 PSI for maximum performance)

Grundfos Pump Model UPS 15-78

Sound Level

CH: 42 dB(A)

DHW: 44 dB(A)

CH: 42 dB(A)

DHW: 47 dB(A)

Electrical Data

Normal (CH) 144 W 158 W 158 W

Normal (DHW) 174 W 174 W 194 W

Standby 4 W

Max Current 6 Amps

Fuse 10 Amps x 2

Gas Supply

Pressure

1

Natural Gas 3.5 in. - 10.5 in. W.C. (0.87 - 2.61 kPa)

Propane 8.0 in. - 13.5 in. W.C. (1.99 - 3.36 kPa)

Electric Connecons AC 120 Volts, 60 Hz

Cercaons ANSI Z21.13, CSA 4.9, ASME

Canada CRN 2089.9CL

Rinnai I-Series Condensing Boiler Combi Manual 11

Measurements: in. (mm)

Vent Connecon: 2 in. (51 mm) nominal PVC/Polypropylene or 3 in./5 in. Concentric

12 Rinnai I-Series Condensing Boiler Combi Manual

Central Heang

Return

Central Heang

Supply

Domesc

Hot Water

Gas

Domesc

Cold Water

Condensate

Drain

Connecon Connecon Size

Gas 3/4 in. NPT

DWH In (Cold Inlet) 3/4 in. NPT

DHW Out (Hot Outlet) 3/4 in. NPT

CH In (CH Return) 1 in. NPT

CH Out (CH Supply) 1 in. NPT

Condensate Outlet 1/2 in. NPT

Rinnai I-Series Condensing Boiler Combi Manual 13

The following oponal accessories are available for the Rinnai I-Series Condensing Boiler.

CONDENSATE NEUTRALIZER

Part #: 804000074

Neutralizes the condensate

generated by the boiler.

SCALECUTTER

Part #: 103000038

Filters and reduces the amount of

scale entering the boiler allowing

for greater boiler longevity.

SCALECUTTER REFILL CARTRIDGE

Part #: 103000039

Rell cartridge for the ScaleCuer

lter assembly.

DHW ISOLATION VALVE KIT

Part #: MIVK-T-LW

For quick isolaon of the

boiler DHW connecons.

PRIMARY-SECONDARY HEATING KIT

Part #: 807000212

DHW TEMPERATURE CONTROLLER

Part #: MC-601

14 Rinnai I-Series Condensing Boiler Combi Manual

• Installaon Guidelines

• What You’ll Need

• Items Included

• Choose an Installaon Locaon

• Mount the Boiler to the Wall

• Fill the Condensate Collector

THIS SECTION IS INTENDED

FOR THE INSTALLER

Installer qualicaons: A trained and qualied

professional must install the appliance,

inspect it, and leak test the boiler before use.

The warranty will be voided due to any

improper installaon. The trained and

qualied professional should have skills such

as: Gas sizing; Connecng gas lines, water

lines, valves, and electricity; Knowledge of

applicable naonal, state, and local codes;

Installing venng through a wall or roof; and

training in installaon of condensing boilers.

Training for Rinnai Condensing Boilers is

accessible online at

www.trainingevents.rinnai.us.

Topics in this secon

4

• This boiler is cered for installaon in

residenal and commercial applicaons.

• This boiler is suitable for combinaon

water heang and central heang.

• The installaon must conform with local

codes or, in the absence of local codes,

with the Naonal Fuel Gas Code, ANSI

Z223.1/NFPA 54, or the Natural Gas and

Propane Installaon Code, CSA B149.1. If

installed in a manufactured home, the

installaon must conform with the

Manufactured Home Construcon and

Safety Standard, Title 24 CFR, Part 3280

and/or CAN/SCA Z240 MH Series, Mobile

Homes.

• The appliance, when installed, must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, with the Naonal Electrical Code,

ANSI/NFPA 70, or the Canadian

Electrical Code, CSA C22.1.

• The appliance and its main gas valve

must be disconnected from the gas

supply piping system during any

pressure tesng of that system at test

pressures in excess of 1/2 psi (3.5 kPa)

(13.84 in W.C.). For system tesng at

pressures less than or equal to 1/2 psi

(3.5 kPa) (13.84 in W.C.) the appliance

must be isolated from the gas supply

piping by closing its individual manual

shuto valve.

• You must follow the installaon

instrucons and those in secon

“5. Venng” for adequate combuson

air and exhaust.

• If this boiler’s DHW system is connected

to a closed water supply system, such as

one having a backow preventer in the

cold water supply line, means shall be

provided to control thermal expansion.

Contact the water supplier or local

plumbing inspector on how to control

thermal expansion.

• Should overheang occur or the gas

supply fail to shut o, turn o the

manual gas control valve to the

appliance.

• Combuson air must be free of

chemicals, such as chlorine or bleach,

that produce fumes. These fumes can

damage components and reduce the life

of your appliance.

• Where required by the authority having

jurisdicon, the installaon must comply

with the Standard for Controls and

Safety Devices for Automacally Fired

Boilers, ANSI/ASME CSD-1.

Rinnai I-Series Condensing Boiler Combi Manual 15

DO NOT install the boiler in an area

where water leakage of the unit or

connecons will result in damage to

the area adjacent to the appliance

or to lower oors of the structure.

When such locaons cannot be

avoided, it is required that a

suitable drain pan, adequately

drained, be installed under the

boiler. The pan must not restrict

combuson air ow.

DO NOT install the boiler in an area

with negave air pressure.

DO NOT obstruct the ow of

combuson and venlaon air.

DO NOT use substute parts that

are not authorized for this boiler.

DO NOT install the boiler on

carpeng.

DO NOT

Gather the recommended tools and parts

before starng installaon.

Items Needed

• Pressure relief valve for domesc

hot water (150 PSI / 1,034 kPa)

• Pressure/Temperature Gauge

Note: When aaching the pressure/

temperature gauge, please comply

with applicable codes and the ASME

standard.

• Low loss header or closely spaced

tee

• Expansion tank for a closed heang

system

• Isolaon valve kit or equivalent

components (for quick isolaon of

the boiler for service and/or

maintenance)

• Air separator

• Standard tools for central heang,

gas ng, plumbing and electrical

wiring.

• Digital manometer

• Digital mulmeter capable of

reading microamps

• pH digital meter or test strips

• For wall mounng bracket

installaon:

− Level

− Screws (use appropriate screws

for type of wall construcon)

Other Items You May Need

• Combuson analyzer (intended for

use with condensing boilers)

• Hand truck with fastening belt

• Ensure the wall is of sucient

strength to support the weight of the

boiler, piping and any other

components needed for installaon;

if it is not, please reinforce the wall as

appropriate.

• Operang limits of the boiler:

Maximum boiler set

point temperature:

180°F (82 °C)

Maximum operang

pressure:

45 psi (3.1 bar)

Maximum allowable

working

temperature ASME:

210°F (99°C)

Maximum allowable

working pressure

ASME:

45 psi (3.1 bar)

16 Rinnai I-Series Condensing Boiler Combi Manual

Carefully unpack your boiler system and verify the following contents are included. If any items are

damaged or missing, contact your local dealer/distributor. Do not aempt to use any item that

appears damaged.

• Installaon and Operaon Manual (this manual)

• User Manual

• Warranty Card

• Technical Data Sheet (located on inside of boiler front panel)

• “Key Points for a Successful Installaon” sheet (adhered to boiler

front panel)

Vent top with integrated

2 in. PVC and

3 in. X 5 in. Concentric

Vent Adapter

Pump

Air

Supply

Filter

Refer to secon

“3.3 Components”

for a complete list of

integrated parts.

WALL MOUNTING BRACKET

PRESSURE RELIEF VALVE

For Central Heang Systems

OUTDOOR TEMPERATURE

SENSOR

VENT SCREENS

Vent screens (x2) and vent

screen screws (x2). The vent

screen prevents debris and

other objects from entering the

terminal. One vent screen is for

the intake; the other is for the

exhaust.

LIQUID PROPANE FIELD CONVERSION KIT

This boiler is congured for Natural Gas only. Use this kit to convert to

Propane Gas if needed. Contents include:

Orice

Outer Gasket Inner Gasket

Conversion Rang Plate

DOCUMENTATION

PART #:

805000096

PART #:

807000211

PART #:

109000628

INTEGRATED ITEMS

Rinnai I-Series Condensing Boiler Combi Manual 17

Contaminant Maximum Level

Total Hardness Up to 200 mg/L

Aluminum * Up to 0.2 mg/L

Chlorides * Up to 250 mg/L

Copper * Up to 1.0 mg/L

Dissolved Carbon Dioxide

(CO2)

Up to 15.0 mg/L

Iron * Up to 0.3 mg/L

Manganese * Up to 0.05 mg/L

pH * 6.5 to 8.5

TDS (Total Dissolved

Solids) *

Up to 500 mg/L

Zinc * Up to 5 mg/L

Consideraon of care for your boiler should

include evaluaon of water quality.

• The water must be potable, free of

corrosive chemicals, sand, dirt, or other

contaminants.

• It is up to the installer to ensure the

water does not contain corrosive

chemicals or elements that can aect or

damage the boiler.

• Water that contains chemicals

exceeding the levels below can damage

the boiler.

* Source: Part 143 Naonal Secondary Drinking Water Regulaons

When choosing an installaon locaon, you

must ensure that clearances will be met and

that the vent length will be within required

limits. Consider the installaon

environment, water quality, and need for

freeze protecon. Requirements for the gas

line, water lines, electrical connecon, and

condensate disposal can be found in their

respecve installaon secons in this

manual.

This secon provides informaon on the

importance of water quality to the Rinnai

Condensing Boiler. The informaon is

intended to serve as general guidelines only

and is not a complete list of water quality

guidelines.

• Unsuitable heang system water can cause

the formaon of scale or sludge, which

aects system eciency. It can also cause

corrosion and reduce life of the heat

exchanger.

• Never use water that has been treated by a

reverse osmosis, deionized, or dislled

water to soen the water to ll the heang

system.

• For Domesc Hot Water systems, if you

install the boiler in an area that is known to

have hard water or that causes scale build-

up, the water must be treated and may

require a more frequent ushing schedule.

Scale build-up is caused by hard water and

can be accelerated if the boiler is set at a

high temperature. Rinnai oers

Southeastern Filtraon’s “ScaleCuer Water

Condioning System” that oers superior

lime scale prevenon and corrosion control

by feeding a blend of control compounds

into the cold water supply.

• Oxygen permeable or rubber tubing is not

permied in the heang system unless it is

separated from the boiler by a plate heat

exchanger.

• Thoroughly ush the system prior to lling.

While ushing, isolate the boiler.

• Do not introduce any system cleaner into

the boiler. Flush the system thoroughly to

remove all system cleaner before lling the

boiler with water.

• When freeze protecon of the heang

system is desired, only use Rinnai-approved

anfreezes. The allowed maximum

concentraon is 40%.

• Reference secon “14.1 Approved Cleaners,

Inhibitors and Anfreezes” in the Appendix

for an approved list of system cleaners,

inhibitors, and anfreezes.

IMPORTANT

Replacement of components due to

water quality damage is not covered by

the warranty.

18 Rinnai I-Series Condensing Boiler Combi Manual

Use this checklist to ensure you have selected the correct locaon for the boiler.

Air surrounding the boiler, venng, and vent terminaon(s) is used for combuson and must be

free of any compounds that cause corrosion of internal components. These include corrosive

compounds that are found in aerosol sprays, detergents, bleaches, cleaning solvents, oil based

paints/varnishes, and refrigerants. The air in beauty shops, dry cleaning stores, photo processing

labs, and storage areas for pool supplies oen contains these compounds. The boiler, venng, and

vent terminaon(s) should not be installed in any areas where the air may contain these corrosive

compounds.

Locaon Clearance

Top 2 in. (51 mm)

0 in. from vent components

Boom (Ground) 12 in. (305 mm)

Front

6 in. (152 mm)

Clearance for servicing is

24 in. (610 mm) in front

of boiler

Back 0 in.

Sides (Le and Right) 2 in. (51 mm)

Vent 0 in.

□

The boiler is not exposed to corrosive compounds in the air.

□

The boiler locaon complies with the required clearances.

□

The planned combuson air and exhaust terminaon locaons meet the required clearances.

□

The water supply does not contain chemicals or exceed total hardness that will damage the

heat exchanger.

□

A standard 3 prong 120 VAC, 60 Hz properly grounded wall outlet or other 120 VAC, 60 Hz

source is available.

□

The installaon must conform with local codes or, in the absence of local codes, with the

Naonal Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installaon

Code, CSA B149.1.

Top

Boom

WALL

2 in. (51 mm)

Minimum

12 in. (305 mm)

Minimum

2 in. (51 mm)

Minimum

Right image is not to scale and is for illustraon

purposes only.

Side

Front

Rinnai I-Series Condensing Boiler Combi Manual 19

Supplied by Installer:

• Level

• Four screws for mounng bracket

installaon

• Screws for top and boom bracket

installaon

Use appropriate screws for type of

wall construcon.

Hold the wall mounng bracket up

against the wall and use a level to

make sure the bracket is even. Proper

operaon requires the boiler to be

level.

Use four screws to secure the wall

mounng bracket to the wall (two

screws on far le side and two

screws on far right side).

Use the appropriate screws for the

wall construcon to secure the

mounng bracket to the wall

between two studs.

You Will Need:

• Rinnai Condensing Boiler

• Wall Mounng Bracket

Level

Wall Mounng Bracket

Insert the top bracket into the wall

mounng bracket. Make sure the wall

mounng bracket is aached to the wall

and can hold the weight of the boiler

before you fully let go.

Boiler

Right Side

Steps connued on next page.

Instrucons:

20 Rinnai I-Series Condensing Boiler Combi Manual

Securely screw the top and boom

brackets into the wall, making sure

the screws are ush with the wall.

• Use any of the holes in the top

and boom brackets.

• Make sure the securing method is

sucient to support the weight of

the boiler. Refer to the boiler

weight in secon “3.4

Specicaons” of this manual.

The boiler must be installed in an

upright and level posion. Do not

install the boiler upside down or on

its side.

IMPORTANT

The condensate collector must be lled with

water prior to installing the vent system.

Pour approximately 10 ounces (1.25 cups) of

water directly into the boiler’s exhaust port

(do not remove the 2 in. PVC adapter prior to

this).

Before operaon of the boiler, the

condensate collector must be lled with

water. This is to prevent the potenal of

exhaust gasses from entering the building.

Failure to ll the condensate collector could

result in severe personal injury or death.

Exhaust

Port

WARNING

Top Bracket

Boom Bracket

Page is loading ...

Rinnai REB-A1800FF-US Installation guide

Rinnai REB-A1800FF-US Installation guide

Related papers

Other documents