Ohlins SUR4I50 Mounting Instruction
- Category
- Car kits
- Type
- Mounting Instruction
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00
fax +46 8 590 025 80
© Öhlins Racing AB. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
Öhlins McPherson Strut for Subaru Impreza N12 B - rear
SUR3I50-4I50
Mounting Instructions
Note!
Please note that this image is a general representation of
the product and may differ slightly from your product.
Note!
Please note that during storage and transportation,
especially at high ambient temperature, some of the oil
and grease used for assembling may leak and stain the
packaging. This is in no way detrimental to the product,
wipe off the excessive oil/grease with a cloth.
Before installing this product, check the contents of the
kit. If anything is missing, please contact an Öhlins dealer.
Kit Contents
Part No Pcs
McPherson Strut SUR3I50/4I50 1
Öhlins Sticker 00192-01 2
C-spanner McPherson 01796-01 1
Rebound adjuster tool 01822-03 1
Camber bushings
offset 2,44* 05794-01 2
offset 1,88* 05794-02 2
offset 1,32* 05794-03 2
offset 1,76* 057494-04 2
offset 0,20* 05794-05 2
Foam lter** 06057-03 2
Owner’s Manual 07440-02 1
Recommended set-up
Compression damping
Low speed .......................... 25±5 clicks
Available range .................. 5-20clicks
High speed ......................... 20±5 clicks
Available range .................. 5-40clicks
Rebound damping .............. 44±2 clicks
Available range .................. 20-50 clicks
Standard Spring
Part No. .............................. 06773-05
Rate .................................... 35N/mm
Optional Springs
Part No Rate
06773-03 ............................ 30N/mm
06773-07 ............................ 40N/mm
06773-09 ............................ 45N/mm
ADJUSTMENTS
Part no. MI_SUR3I50-4I50_3
Issued 2013-03-14
Spring Preload
Adjuster
Low
speed
Rebound
Warning!
Before riding, always make sure that the basic settings
made by Öhlins are according to recommended
Set-up Data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make any
adjustments. Contact an Öhlins dealer if you have any
questions about setting up.
Warning!
Before installing this product, read the Öhlins Owner’s
Manual. The shock absorber/front fork/steering damper
is an important part of your vehicle and will affect
the stability.
SET-UP DATA
Tool
01822-03
Compression
High
speed
1 2
MOUNTING INSTRUCTIONS MOUNTING INSTRUCTIONS
Warning!
It is advisable to have an Öhlins dealer install the shock
absorber/front fork/steering damper.
Warning!
If working on a raised vehicle, ensure it is securely
supported so that it will not tip.
Note!
Before mounting this product clean the vehicle thoroughly.
Note!
When working on this product, always see the Vehicle
Service Manual for vehicle specic procedures and
important data.
1
Raise the vehicle so that the rear wheels are
off the ground.
2
Remove the rear wheels.
3
Loosen the bolts for the lower attachments.
Caution!
Support the wheel hubs in an appropriate way on each
side of the vehicle so that the brake hose and/or drive
shaft joint can not be damaged.
4
Loosen the upper attachment from the top
mount and remove the original McPherson
strut.
5
Install the Öhlins McPherson strut on the
top mount. Tighten Nut (00139-04) with
torque 60Nm.
Caution!
Make sure the reservoir is protected from damages (e.g.
stone ship).
6
Lift up the wheel hub with a hydraulic jack
to remove any freeplay of the bolts before
tightening the bolts around the wheel upright.
The reservoir shall point towards the front of
the vehicle.
Caution!
Ensure that all screws are tightened to the correct torque
and that nothing fouls or restricts movement of the shock
absorber/front fork/steering damper when the suspension
is fully compressed or extended.
5
6
Top mount
Example Right - rear
00139-04
60Nm
05952-02
05952-02
STI SD203704S050
Flange nut
00139-04
Sleeve
00123-15
Flange bolt
00432-03
Wheel upright
Reservoir
Camber
bushing
05794-00
to the front
-
1
-
2
Ohlins SUR4I50 Mounting Instruction
- Category
- Car kits
- Type
- Mounting Instruction
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ohlins PBQ 6Q00 Mounting Instruction
-
-
-
-
-
-
-
-
-
