WT07
WIFI PANIC KNOB
- Built-in WIFI module that sends all alerts to your Smartphone
- Super low power consumpon, typically only 2 x AAA baeries/year
- Separate low baery and loss of signal noficaons
- Life-me cloud service provided free of charge
- Powerful APP for your Smartphone provided free of charge
- User can create floorplans in the APP showing device locaon
- APP records last 30 acvaons me and date stamped
- 3M double sided tape for permanent fixing included
- Blue LED for status indicaon
Once the magnet (smaller part with the handle) is moved away from the reed switch (built into the larger part), the unit will send an
alarm signal to your smart phone via your home/business WIFI connecon. Such signal is selectable as an Alarm Sound + Nofica-
on, Noficaon Sound + Noficaon or just a silent Noficaon. By using our powerful free APP and free worldwide cloud service,
a user can monitor the safety or security of a locaon ANYTIME, ANYWHERE!
Geng started
Congratulaons on your purchase of this powerful WIFI Panic Knob. This product works together with your smart phone and
internet via WIFI. Please check that your smart phone is either an Android or IOS (iPhone) and that the latest firmware has been
installed. Please also check that your WIFI router is working properly and that its operang manual confirms that it operates on 2.4
GHz with WPA/WPA2 encrypon.
Installing the APP
1/
2/
3/
Seng up your PANIC KNOB
1/
2/
3/
Before powering up the Sensor, please install our free ‘NEXUSHOME ‘ APP onto your phone. The APP is available in an IOS version
on the Apple App Store and an Android version on the Google Play Store. Ensure your phone is connected to WIFI to complete
your account setup.
Once downloaded, click and open the APP. The following message will appear. Please click OK.
Now complete your User Profile by inpung your email address and a 6 digit password. Click the REGISTER buon, check your
email and click the link in the email from “Nefy” to complete registraon.
Aer compleng the APP registraon, you are now ready to setup each Sensor.
Carefully unscrew and open the baery cover. Insert two new, good quality
Alkaline AAA baeries, ensuring correct polarity.
Connect the Sensor to your smartphone using the cable that has been
provided
a- one side is a 3.5mm audio jack which you need to plug into the
headphone output of your smartphone.
b- the other side is a micro USB jack which you need to plug into the small
USB socket on the side of the Sensor.
Choose the Building locaon where you eventually wish to permanently install
your Panic Knob. Look at your smart phone at that locaon and ensure you
have a good and steady WIFI connecon there.
1
1
2
2
3
3
install click OK register
4/
5/
6/
7/
8/
9/
Now, exit the APP and open SETTINGS on your smart phone. VERY IMPORTANT. The Sensor will only communicate Alarm signals
to the WIFI router that you are about to “pair” it to. If the Sensor is or goes out of range of that specific router, then it will not
work. This also means that if you have WIFI Extenders/Repeaters in your WIFI network and you wish to install/use the Sensor in
the vicinity of that Extender, rather than the main Router, you will need to pair the Sensor to that Extender and NOT to the Router.
Each Router or Extender has its own unique reference name (or SSID) and this is what you are now going to pair to:
Re-Open the APP and click PROFILE at the boom of the opening HOME page. This will take you to the APP’s SETTINGS
Page. Click “ADD DEVICE/WI-FI SETTING”
You will see the same SSID of the Router/Extender that you selected in your phone’s WIFI Sengs. Enter the password of that
Router or Extender and press PAIR NEW DEVICE.
The Sensor will now start pairing to the Router or Extender and you will see the wheel whirling. It can take up to 60 seconds for a
“pairing successful” message to appear. If you see the message “me out, try again”, move the smartphone, sll with the Sensor
aached, closer to the Router or Extender and repeat the process. Once paring is successful, you can now unplug the cable and
close the baery door. Mount the Panic Knob into a permanent locaon using the double sided tape provided.
Exit the PAIRING Page in the APP by clicking at the top of the screen (iOS only, for Android users press Backwards on your
Smartphone). Then, click at the top of the APP’s SETTING PAGE to return you to the APP’s Home Screen. Now press SECURITY
SENSOR TAG. This will take you to the Alert Mode Screen. This allows you to choose the Sound you will hear on your phone
when an Alarm noficaon is received from both this Sensor and all other Nexus devices you may have paired to your Router.
Click at the boom of the screen. This will take you to the DEVICE page. Here you will see all the Sensors, including any other
type of Nexus sensors that have been paired to the APP.
With SETTINGS open on your smart phone open, check what is showing in “WIFI”. If you just have a main Router, it should be
showing the SSID of this Router. However, if you have a network with one or more extenders, it may also be showing the SSID
of an overlapping Extender as in the picture to the right. In this case, check whether you are closest to the main Router or to
an Extender and select the closest/strongest SSID (i.e. the Router reference name).
Alert Mode
Safe Mode
Silent Mode
Off Mode
Move the magnet away from the reed switch to test the Sensor. You will see the blue LED flash once followed, a few seconds
later by a further two quick flashes, to indicate anoficaon Alert has been sent to the APP. Depending on the Alert Mode
you have chosen, this will be audible or silent. You will see the noficaon appear and the Device will start to
flash with the Alert’s me and date stamped alongside. Press the “Refresh” Buon at the top le hand side of the page to
cancel the flashing. If you now press the Device Icon, you will be taken to its HISTORY PAGE which will list the last 30
noficaons
= Short Siren Tone + incoming Noficaon Alert Sound
= No Siren, just an incoming Noficaon Alert Sound
= No Siren, no Alert Sound, just the Noficaon
= No Siren, no Alert Sound and no Noficaon
(although all alerts from the Sensor will sll be listed the DEVICE’s HISTORY page)
4 5 6
connect WiFi click “Add Device/WiFi Setting” enter the name of WiFi and password
7
8 9
pairing 4 different mode device list and history
WT07-A31D Device Alert
02-03-2016 13:58:59
Advanced Informaon for the DEVICE PAGE
How to share an Alert Noficaon from a DEVICE with another Smartphone
1/
2/
3/
4/
5/
How to delete a DEVICE from the APP
Whilst on the DEVICE PAGE, hold and swipe the Devices Descripon to the le of your screen and press
Press this icon to return to the APP’s Alert Mode Screen.
Press this icon to take you to the APP’s Floorplan Screen.
Here you can create personalized Floorplans showing the locaons of Doors and Windows
and individual Sensors (see below)
Ensure that the free ‘NEXUSHOME ‘ APP has been installed on the other Smartphone and complete the registraon process,
following the procedure detailed in “Installing the APP” above.
Press at the top right of the Device Page in the APP on the Smartphone.
Now select the Sensor you wish to share, then press and complete the “Share Device to” box with the other user’s email
address they used when registering their user profile. Press to exit.
Open the APP on that other User’s Smartphone and press PROFILE at the boom of the opening Home Page.
This will take you to the APP’s SETTINGS PAGE. In the secon "Received Device" you will see a number in green. This denotes the
number of Devices that you have selected to share with that User.
Press "Received Device". This will take you to a list of those Devices. The new User can now choose whether to accept or reject
Noficaons from those Devices. Note that the new User can select, separately, on their APP’s Device Alert Page whether such
noficaons are Audible, Silent or Off.
Press to Refresh/Reset the Device Page and stop a flashing Sensor Icon.
Press this Icon, at the top of the page, to return to the APP’s Home Screen
(iOS only, for Android press back on smartphone).
Enables you to share Alert noficaons for a Sensor with any other user who has already
downloaded the Nexus APP. See below for full details. Whilst in this secon, you can
also alter the order in which the Devices are listed on your screen. Press on the
right of the Device whose order you wish to change and then drag it to its new posion
on the screen.
A personalized descripon of the Sensor.
Press the Sensor’s Icon, to go to its HISTORY page and press “WTxx” seen just above the
ID. Complete CHANGE DEVICE NAME and save it.
This is the Device’s unique ID.
Personalized Icon or Photo for the Sensor.
Press the Sensor’s Icon to go to its HISTORY PAGE, then press its Icon
again on this page. Choose “Take photo”, “From album” or “Default
icons” to create a personalized Icon.
Flashing - Indicates a Sensor has sent an Alert noficaon.
Press the Icon to go to the Sensor’s HISTORY PAGE
Indicates a Low Baery.
Although baeries should connue to last for up to a month aer this
Icon appears, you should change them immediately, respecng the
correct polarity and using good quality Alkaline baeries. Always test a
Sensor aer replacing the baeries.
The Sensor sends a “heartbeat” signal to the Router every 4 hours.
This Icon indicates that contact has been lost between them.
Shows that a Device is acve.
Click on this Icon to toggle the Device to be acve or non-acve
Indicates whether the Sensor is also sending an Alert Signal to the
oponal Nexus Indoor Siren (sending a signal as shown). Press the
Sensor’s icon to go to DEVICE HISTORY, then press the Siren Icon on
that page to toggle Off
1
2
3
4
5
press edit press share press “Received Device”
Advanced Informaon for the Floorplan Page
IMPORTANT
1/
2/
3/
Trouble Shoong
1/
a/
b/
c/
d/
2/
a/
b/
c/
d/
Safety
FIRE, BATTERY AND ELECTRIC SHOCK HAZARDS
a/
b/
c/
d/
Do not place any other magnets or magnezed materials close to a Sensor as this could cause a false trigger.
Make sure your WIFI router and its signal strength cover all the Sensors locaons. Please note that a WIFI signal may not
penetrate through concrete walls or solid doors and that, if it does, it is usually SEVERELY reduced. You may therefore need to add
one or more WIFI Repeaters to increase signal coverage. If you do this, then ensure that individual devices are paired to the
closest Repeater or Router. Since all Router/Repeater SSID’s are different, you must ensure that the Sensor is paired to the correct
SSID (see seng up your WIFI Sensor above).
Aer installing a Sensor, please test it at least a couple of mes to check the performance.
CANNOT PAIR THE SENSOR SUCCESSFULLY
Check whether the Sensor has enough baery power. Always use new, good quality, Alkaline baeries.
If there are too many WIFI connecons around your Sensor, turn them off to avoid any disturbance and pair again.
Check that the router is working properly and that it operates on 2.4GHz
Check that the SSID and password are correct.
DOESN’T WORK PROPERLY or LOSS OF SIGNAL ICON APPEARS
Check whether the Sensor is within coverage of your WIFI router/repeater. Move the Sensor or Router to a different locaon.
Check that the router is working properly
Check the power level of the tag. If it shows a baery low icon in the APP, please replace the baeries.
Check that the magnet and reed switch are aligned correctly with the arrows directly opposite each other.
Do not drop, disassemble, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint, or insert foreign objects into
the Sensor. Such acons could result in an electric shock. Clean the Sensor only with a dry cloth.
Do not expose the Sensor to extremely high or low temperatures or leave them in direct sunlight for extended periods of me.
Do not leave the Sensor near open flames such as cookers, candles or fireplaces.
It’s dangerous if you replace baeries incorrectly or with the wrong polarity. You should only use the same or equivalent type of
baery to replace a damaged or drained one. The Baery should not be exposed to an overheang environment such as extreme
sunshine or fire. Always use a good quality Alkaline baery for best results.
Swipe the screen to the Le to reach a new Floorplan
Press to add an addional Floorplan.
Press to show the list of all your Devices. Then press on an individual device
from that list to add it to that Floorplan. Press to add an addional Floorplan.
Drag a Device Icon here to delete it from that Floorplan.
Press to turn Devices on this page On/Off .
Press to edit the Floorplan on the screen. This will then take you to the screen
below le.
Press to remove all from this Floorplan
(Boom Right) Drag a Shock Sensor Icon here to
delete it from that Floorplan
Press to Save the Drawing
Whilst in Eding Mode:
Use your finger on the screen up/down/sideways
to create a drawing
Press to delete this Floorplan completely
Press to delete your last acon
Press to add Door/Window Symbols, drag to
Floorplan locaon, press screen to return
/
