Intermec EasyCoder 501 SA Installation guide

EasyCoder 501 SA
Intermec
Brand
Intermec
Model
EasyCoder 501 SA
Type
Installation guide

This manual is also suitable for

Intermec EasyCoder 501 SA is a versatile label printer designed for various applications. With its ability to detect low paper and ribbon levels through its sensor kit, you can proactively monitor and maintain your printing supplies, ensuring uninterrupted operation. The sensor kit includes two photo-electric sensors that track the rotation of the paper supply spool and the ribbon unwind shaft, updating two separate counters for each sensor.

Intermec EasyCoder 501 SA is a versatile label printer designed for various applications. With its ability to detect low paper and ribbon levels through its sensor kit, you can proactively monitor and maintain your printing supplies, ensuring uninterrupted operation. The sensor kit includes two photo-electric sensors that track the rotation of the paper supply spool and the ribbon unwind shaft, updating two separate counters for each sensor.

EasyCoder 501/601
Sensor Kit
P/N 1-960411-02
Edition 3
September 1998
Installation Instructions
EasyCoder 501/601 – Installation Instructions
1
SENSOR KIT
Intermec offers a kit containing two sensors, that detect the rotation
of the paper supply spool and the ribbon unwind shaft and update
two counters, one for each sensor. By means of custom-made
application programs, the counters can be read and used for indicate
paper-low and ribbon-low conditions (as opposed to out-of-paper-
out and out-of-ribbon conditions, which are supported by the
standard error handling). See SYSVAR system array in Intermec
Fingerprint 6.13 Reference Manual
1
.
The Sensor Kit is available for the following printer models:
Model Ribbon Low Sensor Paper Low Sensor
EasyCoder 501 E yes yes
EasyCoder 501 SA yes yes
EasyCoder 601 S yes no
EasyCoder 601 E yes yes
The sensor kit consists of two photo-electric sensors and two #T10
Torx screws.
The sensors require no regular cleaning. However, should any
malfunction be detected, you may try to blow the sensor clear from
dust or paper residue before replacing it.
The sensitivity of these sensors cannot be adjusted.
Introduction
Ribbon Low Sensor
Paper Low Sensor
The illustration shows the sensor kit fitted on an EasyCoder 501 E
printer.
1
/. The system variable SYSVAR reads
the counters as follows:
SYSVAR (12) reads the paper counter
SYSVAR(13) reads the ribbon counter
EasyCoder 501/601
Sensor Kit
Installation Instructions
Edition 3, September 1998
Part No. 1-960411-02
EasyCoder 501/601 – Installation Instructions
2
SENSOR KIT, cont'd.
Installation
Ribbon Low Sensor
• Open the right hand door.
• Turn off the power and remove the left-hand cover.
• From the paper compartment side, insert the connector and cable
through the square hole in the centre-line wall.
• Insert the sensor under the code disk of the ribbon unwind unit so
the disc will run in the U-shaped slot between the receiver and
transmitter.
• Attach the sensor to the centre-line wall by means of one #T10
Torx screw. Check that the code disc can rotate freely.
• Connect the cable to connector P-605 at the top of the CPU board
(marked ➀).
• Continue by fitting the paper low sensor.
Paper Low Sensor
• Remove the three #T20 Torx screws holding the large crescent-
shaped guide plate that surrounds the paper supply unit. Remove
the guide plate.
• Fit the sensor under the code disc of the upper supply unit using
the same method as with the ribbon low sensor.
• Connect the cable to connector P-602 at the top of the CPU board
(marked ➁).
• Fit back the guide plate and the left-hand cover.
Note!
The ribbon unwind unit and the paper
supply unit are shown dismounted in
the drawing only to improve visibility.
In reality, the only part that requires
dismounting is the guide plate.
Guide Plate
(remove)
Ribbon Unwind Unit
(do not remove)
Paper Supply Unit
(do not remove)
Sensor
#T10 Torx screw
#T20 Torx screw (3x)
Sensor
#T10 Torx screw
  • Page 1 1
  • Page 2 2
  • Page 3 3

Intermec EasyCoder 501 SA Installation guide

EasyCoder 501 SA
Intermec
Brand
Intermec
Model
EasyCoder 501 SA
Type
Installation guide
This manual is also suitable for

Intermec EasyCoder 501 SA is a versatile label printer designed for various applications. With its ability to detect low paper and ribbon levels through its sensor kit, you can proactively monitor and maintain your printing supplies, ensuring uninterrupted operation. The sensor kit includes two photo-electric sensors that track the rotation of the paper supply spool and the ribbon unwind shaft, updating two separate counters for each sensor.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents