Symmons FSTF367220STN Installation guide

Symmons
Brand
Symmons
Model
FSTF367220STN
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

Symmons FSTF367220STN is a floor standing tub filler with a variety of features that can enhance your bathing experience. The 60" flexible metal hose and 1 mode hand shower provide convenience and flexibility, allowing you to direct the water flow exactly where you need it. The ceramic cartridge ensures smooth and precise water control, while the push button allows you to effortlessly divert the water from the spout to the hand shower. With a flow rate of 2.0 gpm (7.6 L/min) for the hand shower and 5.3 gpm (20.1 L/min) at 45 psi or 6.5 gpm (24.

Symmons FSTF367220STN is a floor standing tub filler with a variety of features that can enhance your bathing experience. The 60" flexible metal hose and 1 mode hand shower provide convenience and flexibility, allowing you to direct the water flow exactly where you need it. The ceramic cartridge ensures smooth and precise water control, while the push button allows you to effortlessly divert the water from the spout to the hand shower. With a flow rate of 2.0 gpm (7.6 L/min) for the hand shower and 5.3 gpm (20.1 L/min) at 45 psi or 6.5 gpm (24.

DURO™
Model Numbers Feature Highlights
FSTF367220
Floor Standing Tub Filler
Operation & Maintenance Manual
☐FSTF367220 Floor standing tub filler
Compliance
- ASME A11.18.1
- CSA B125.1
Options/Modifications
Note: Append appropriate -sux to model number.
Dimensions
c
Limited Lifetime - to the original end
purchaser in consumer/residential
installations.
10 Years - for commercial/industrial
installations. Refer to
www.symmons.com/warranty for
complete warranty information.
Warranty
Note: Dimensions subject to change without notice.
☐STN Satin nickel finish
☐MB Matte black finish
☐BBZ Brushed bronze finish
• Ceramic cartridge
• Push button to divert from spout to hand shower
• 60" flexible metal hose
• 1 mode hand shower
• 2.0 gpm (7.6 L/min) hand shower
• Floor Standing Tub Filler shall be metal construction
plated in standard polished chrome finish
• 5.3 gpm (20.1 L/min) at 45 psi tub filler
• 6.5 gpm (24.6 L/min) at 60 psi tub filler
A
B
C
D
E
F
Measurements
A7", 178mm
B2X1/2-14NPSM
C32-5/16", 821mm
D11-5/8", 296mm
E8-7/8", 225mm
F31-1/8", 790mm
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2021 Symmons Industries, Inc. ■ symmons.com ■ [email protected]om ■ ZV-3516 REV 0 ■ 042222
Installation A) Wooden subfloor with access underneath
Section A: (Steps 1-4)
1. Measure and mark centerlines for mounting bracket
installation using dimensions in the subfloor(1 1/2" thick)
where you would like the faucet to be located.
2. Drill a hole 2" and (4x) 1/4" holes. Use the floor
flange(1) as a template.
3. Align with the holes of the floor flange(1) and the
holes in the floor and insert (4x) bolts(2).
4. From underneath, install the holding plate, wash-
ers, lock washers, and nuts(4). Tighten the nuts with a
wrench.
Section B: (Step 5)
5. Install flooring around the floor flange.
Section C (Steps 6 & 7)
6. Slide the decorative flange onto the faucet body.
7. Attach the flange to the body, using the 4 screws
provided.
Section D (Step 8-10)
Direct Faucet body Installation:
8. Connect the faucet body and the floor flange togeth-
er using the screws provided.
Note: do not tighten screws entirely.
9. Before tightening the screws, rotate the faucet body
in order to obtain the desired position for the spout.
10. Slide the decorative flange towards the floor.
Section E (Step 11)
11. Connect the cold and hot water inlets. Check for
leaks.
Section F (Step 12)
12. Connect the hose and handshower to the shower
holder connector. Check for leaks.
Section A
Section C
Section B
Section D Section E
Section F
a)
b)
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2021 Symmons Industries, Inc. ■ symmons.com ■ [email protected]om ■ ZV-3516 REV 0 ■ 042222
Installation B) Subfloor without access underneath
Section A: (Steps 1-3)
1. Measure and mark centerlines for mounting bracket
installation using dimensions in the subfloor(1 1/2" thick)
where you would like the faucet to be located.
2. Drill a hole 2" and (4x) holes (diameter depends on
screws that customer used). Use the floor flange(1) as a
template.
3. Flexible hose 1/2-14 NPSM, aligned with the corner
holes of the floor flange and use appropriate screws ac-
cording to the surface you are fastening the floor flange
to (screws not included).
Note: The floor flange can be flipped and used as shown
if necessary.
Section B: (Step 4 & 5)
4. Slide the decorative flange onto the faucet body.
5. Attach the flange to the body, using the 4 screws
provided.
Section C (Steps 6)
6. Connect the cold and hot water inlets. Check for
leaks.
Section D (Step 7-9)
7. Push the connected flexible hoses under the subfloor,
then connect the faucet body and the floor flange to-
gether using the screws provided.
Note: do not tighten screws entirely.
8. Before tightening the screws, rotate the faucet body
in order to obtain the desired position for the spout.
9. Slide the decorative flange towards the floor.
Section E (Step 10)
10. Connect the hose and handshower to the shower
holder connector. Check for leaks.
Section A
Section C
Section B
Section D Section E
DEPENDS ON SCREWS THAT
CUSTOMER USED
a)
b)
Flexible hose 1/2-14 NPSM
Max Ø 2” (51 mm)
  • Page 1 1
  • Page 2 2
  • Page 3 3

Symmons FSTF367220STN Installation guide

Symmons
Brand
Symmons
Model
FSTF367220STN
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for

Symmons FSTF367220STN is a floor standing tub filler with a variety of features that can enhance your bathing experience. The 60" flexible metal hose and 1 mode hand shower provide convenience and flexibility, allowing you to direct the water flow exactly where you need it. The ceramic cartridge ensures smooth and precise water control, while the push button allows you to effortlessly divert the water from the spout to the hand shower. With a flow rate of 2.0 gpm (7.6 L/min) for the hand shower and 5.3 gpm (20.1 L/min) at 45 psi or 6.5 gpm (24.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents