Steering Wheel Interface(SWI) Operation
Make Connector SWC1 SWC2 SWC-GND
Chevy/Buick/Olds/PŽŶƟĂĐ
AA6N/AA7
APPLICABLE VEHICLES
Ford/Lincoln/Mercury
B18N/A19
2004-09 Buick
C 14 N/A RG* 2000-08 Chevrolet
2004-12 Ford*
HondĂͬcuƌĂ
D7N/A6
2003-12 HondĂ
E 3 N/A RG* 2006-13 HyundĂŝ
F16N/A5
2006-13 <ŝĂ
2003-12 Lexus
<ŝĂͬ,LJƵndĂŝ
G18N/A19
2003-11 Lincoln
H6N/A18
2003-12 DĂnjdĂ
I4N/A17
2003-11 Mercury
J5N/A6
2005-11 NissĂŶ
2002-04 Oldsmobile
DĂnjdĂ
K6N/A5
2001-08 PŽŶƟĂĐ
2004-12 Scion
NissĂŶ
L166 15
2003-13 ToLJŽƚĂ
M7574 76
N706971
*2012 Ford F-150
O232225
Not compĂƟble
P222123
Q1312 14
ToLJŽƚĂͬ^ĐŝŽŶ/Lexus
R212223
S78 6
*RG = Ground wire from the ƌĂdio hĂƌness
APPLICABLE VEHICLES
2004-12 AcuƌĂ
This unit only works with analog steering wheel controls.
Does not support any data-bus system.
IMPORTANT
Chevrolet/
Buick/ Olds/
Pontiac
Ford/
Lincoln/
Mercury
Honda
Kia/
Hyundai
Mazda
Nissan
Toyota/
Scion
24-PIN
(front facing)
24-PIN
(front facing)
20-PIN
(front facing)
20-PIN
(front facing)
20-PIN
(front facing)
24-PIN
(front facing)
24-PIN
(front facing)
24-PIN
(front facing)
24-PIN
(front facing)
20-PIN
(front facing)
24-PIN
(front facing)
20-PIN
(front facing)
16-PIN
(front facing)
16-PIN
(front facing)
16-PIN
(front facing)
8-PIN
(front facing)
8-PIN
(front facing)
28-PIN
(front facing)
20-PIN
(front facing)
NOT MAIN POWER CONNECTOR
NOT MAIN POWER CONNECTOR
NOT MAIN POWER CONNECTOR
In the event of the interface, you can set the function value of the button, touch the
N/A area will pop-up the value, touch the button up or down to search the function
value. When the selected value to touch it determine the value by the button; You can
set the unit’s system a total of six buttons, there are ten optional functions: VOL-/VOL
(volume adjustment), CH-/CH(TV channel scan), SEEK-/SEEK(manual ne-tuning(short
press)/scan channels(long press), MUTE, MODE, POWER, Talk; Will be set after the
button above. Pressing [return] icon after setting. As shown below:
From the point we can see, setting up ve buttons, set the VOL+,VOL-,CH+,CH-, MODE
ve functions according to individual needs, set the button’s function corresponding value.
When the need to re-set button on the steering wheel controller efunction value, touch
[RESET] button to life the value of the button’s function, then repeat the above steps,
re-set the desired fuction value.
Steering wheel controller’s SWC1
Steering wheel controller’s SWC-GND
Steering wheel controller’s SWC1
Steering wheel controller’s SWC-GND
Steering wheel controller’s SWC2
Single-wire analog steering wheel controller
Double-wire analog steering wheel controller
SWI Wiring Diagram
RESET
SETTING
R1 R2 R3 R4 R5 R6
S1 S2 S3 S4 S5 S6
1
2
3
4
J1
R2 R1 R6
R5 R4 R3
S2 S1 S5
S5 S4 S3
SWC1
SWC2
Note. According to vehicle type, please change the IMPEDANCE setting from GENERAL
menu if the steering wheel control does not work.
