Cooper Lighting Ethernet Interface Module, EIM Installation guide

INS #

Installation Instructions

Model# EIM

Ethernet Interface Module

Module d’interface Ethernet

Del software de interfaz de Ethernet

General Information

The Ethernet Interface Module (EIM) is a device that

makes communications from a PC to a Greengate

panel or network of panels possible over an Internet

connection. The PC can be local within the building

complex or located at a remote location.

The Ethernet Interface Module (EIM) converts data

packets sent over the TCP/IP connection to RS-232

communications. One Ethernet Interface Module (EIM)

is needed per Lighting Control Network unless using the

VisionTouch software. If VisionTouch software is being

used, it is recommended that an Ethernet Interface

Module be dedicated to VisionTouch use. Please contact

technical support for further details. If panels are not

networked, one Ethernet Interface Module (EIM) will be

needed per panel. The Ethernet Interface Module (EIM)

Device Package comes with the following:



Ethernet Interface Module (EIM) device



AC Power Adapter



Cable Package (Contains a crossover cable for

configuration, one phone style serial cable and adapter

head for connection to the lighting panel.)

Status LEDs

RS232 Port

RJ54 Ethernet Port

Power

Input

Reset Button

Typical Layouts

The Ethernet Interface Module may be used to allow

access only from within the internal building LAN or

may also be set up by a qualified network administrator

for external access through the internet. The following

pictures depict these types of configurations.

ROUTER

Lighting Control Panel Connected

to Lighting Control Network

TCP/IP Internet Connection from a Remote Location

Ethernet

Interface

Module

(EIM)

Ethernet Interface Module

Private IP Address: 10.0.0.1

EIM Port Assigned: 10001

Lighting Software set

up to talk to lighting

control panels using

Firewall IP Address

64.30.7.31 and

Firewall

Port 10001.

Firewall Public IP Address: 64.30.7.31

Firewall Port for EIM: 10001 - This

should be the same port number as

the port assigned in the EIM

Firewall Port 10001 is assigned to

direct all traffic coming to this port to

private IP Address 10.0.0.1

Remote Computer

with Lighting Software

INTERNET

FIREWALL

HUB/SWITCH

TCP/IP Intranet Connection from a Local Location

Lighting Control Panel Connected

to Lighting Control Network

Ethernet Interface

Module (EIM)

HUB/

SWITCH

Local Computer with

Lighting Software

Ethernet Interface Module Private IP

Address: 10.0.0.1

EIM Port Assigned: 10001

Lighting Software

set up to talk to

lighting control

panels using EIM IP

Address 10.0.0.1

and EIM Port 10001

NOTE: In this scenario, it is not necessary

to access the external, public internet. The

Ethernet Interface Module may be

accessed directly.

2

Customer Obligations

Ethernet Interface Module

Customer Obligations

The Ethernet Interface Module (EIM) must be configured by

a qualified network administrator. The customer must also

provide an IP address for each Ethernet Interface Module

(EIM) Device being used and be able to support TCP/IP

communications protocol. It may be necessary for the site’s

network administrator to perform firewall programming to

allow for remote access to the device depending on system

setup and desired computer access.

Ethernet Interface Module Conﬁguration

In order for the Ethernet Interface Module (EIM) to work

properly with your application, it will be necessary for the

network administrator to set up the Ethernet Interface

Module (EIM) device(s). Please follow the steps outlined in

this instruction in order for the unit to communicate properly

with the lighting control system. Greengate recommends

using the built-in configuration web server pages in the unit

as the method of configuration.

The instructions that follow describe the setup of the device

using the web server pages.

The following instructions describe what methodology is

used to configure the unit. Regardless of what the important

settings that must be configured, include the following:

1. IP Address must be statically assigned

2. Subnet mask must be set

3. Default Gateway Address must be assigned

4. The IP Port must be configured with a port number.

Port # 10001 is usually an unused port that may be

assigned.

5. The serial settings must be configured properly per the

instructions for communication to the lighting control

network.

Failure to configure the above settings will result in the

failure of the device to communicate with the lighting

control system.

Making the Initial Connection

Before you begin the device configuration, it will be

necessary to configure your Network Interface Card

connection to be on the same subnet as the EIM’s

default IP Address. The default address of the EIM is

192.168.127.254 before configuration. To change your

computer’s TCP/IP settings (Windows XP Steps Shown):

1. Disconnect your LAN Ethernet connection cable from

your computer.

2. Access the Windows Control Panel.

3. Select the Network Connections option.

4. Under the LAN and high-speed internet option, find the

Local Area Connection for your network interface card.

(you may have several listed – if you are not connected

to your building LAN, it will more than likely be the

connection that states “Network cable unplugged”)

5. Right click on the connection and choose Properties

from the pop-up window.

6. In the General tab, scroll down the list of items and

highlight the option for Internet Protocol (TCP/IP).

7. Click on the Properties button.

8. Make note of the current settings so that you can

reconfigure them after configuration is complete.

9. Select the Use the following IP address radial button.

10. Type in an IP Address of 192.168.127.1.

11. Type in the subnet mask 255.255.255.0.

12. Leave all other fields blank.

13. Click on the OK button.

14. Click on the Close button. It may take several seconds

for the new IP settings to take effect.

15. Connect the crossover cable provided from your

computer’s Ethernet port to the EIM’s Ethernet port.

16. Open your internet browser.

1 7. Make certain that cookies are enabled. (please refer

to your internet browser help file for information on

enabling cookies for your browser version).

18. In the browser address window, type in the default EIM

address 192.168.127.254 and press the Enter key.

19. You will be brought to the web console configuration

tool for the EIM.

3

Conﬁguration Settings in the EIM

Ethernet Interface Module

Conﬁguration Settings in the EIM

1. In the menu tree on the left side of the screen, select

the Network Settings folder.

2. In the Network Settings screen, define the following

items:

 IP Address

 Netmask

 Gateway IP Address

 IP Configuration – make certain this is set to Static

3. Select the Submit button.

4. In the Network Settings OK screen, select the Home

button.

5. In the menu tree on the left side of the screen, expand

the Serial Settings folder.

6. Select the Port 1 folder within the Serial Settings folder.

7. In the Serial Settings screen, set the following

parameters:

 Baud rate: 9600

 Data bits: 8

 Stop bits: 1

 Parity: Even

 Flow Control: None

 FIFO: Enable

8. Select the Submit button.

9. In the Serial Settings OK screen, select the Home

button.

4

Connecting the EIM to the Lighting Panel

Ethernet Interface Module

10. In the menu tree on the left side of the screen, expand

the Operating Settings folder.

1. Select the Port 1 folder within the Operating Settings

folder.

2. In the Operating Settings screen, set the following

parameters:

 Operation Mode: TCP Server Mode

 TCP alive check time: 1 minute

 Inactivity time: 0

 Max Connection: 4

 Local TCP port: 10001 recommended (or other port

specified by the IT administrator)

 Other fields not identified should be left at default

settings shown

3. Select the Submit button.

4. In the Operating Settings OK screen, select the Save/

Restart button.

11. Once the Save/Restart OK screen appears, close the

web browser. Configuration is complete.

Remember to reset your computer’s network TCP/IP

settings to their original settings. If you need to reconnect

through the web server pages, you will need to make

certain that your computer is configured to communicate

on the same subnet as the EIM device. Instead of typing in

the default address in the browser address, you will need to

use the unit’s assigned IP Address.

Connecting the EIM to the Lighting Panel

After configuration is complete, it will be necessary to

connect the device to the lighting control panel using the

following steps:

1. Connect the supplied phone style communications

cable to the female 9 pin adapter head provided.

2. Connect the 9 pin adapter head to the Ethernet

Interface Module’s serial port.

3. Connect the other end of the phone style

communications cable to the RJ11 style COM port on

the Lighting Control Panel. (on some controllers there

are two RJ11 style connectors. Please connect the

cable to connector labeled RS-232.)

4. Connect one end of the Ethernet cable to the Ethernet

Interface Module RJ45 port and the other end of the

cable to the Ethernet network.

12. Plug in the power adapter supplied with the device.

ADJ

LCD

RSC POWERRSC LINK

ICD LINK

VCC

GND

TCK

TDO

TDI

TMS

JTAG

TEST

16

32

15

31

14

30

13

29

12

28

11

27

10

26

9

25

8

24

7

23

6

22

5

21

4

20

3

19

2

18

CH

1CH

17CH

ON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSO

PWR

NET+NET

REM

GND+24

REM

LOCAL

PCI-NET

DIGITA

PCI-NETPCI-NET

RS-232

NET

POWER

LSC

TERM

CAN-TX CAN-RX

RESET

50-022180-02

C

PCI 2005

STATUSNET

54-022180-

ANALOG COMAN1AN2AN3AN4

ANALOGS

CW

TP1

TB2

J10

J9

C43

TB1

LED2

LED6

LED3

SR1

IND1

C29

J8

J4

J5

J2

LED4 LED5

J6

J3

LED1

J7

J1

D6D5D4D3

TB3

HUB

Building LAN

Lighting Control Software

The Ethernet Interface Module (EIM)

can be connected to any controller in the network.

AC Adapter

RS-232 Phone Style

Cable with Adapter

Cable Head

RS-485 Network

to Other Lighting

Control Panels

Ethernet Interface

Module (EIM)

5

Diagnostic LEDs

Ethernet Interface Module

Diagnostic LEDs

There are three LEDs located on the top of the EIM unit.

They can be useful in diagnosing proper operation as well

as troubleshooting if necessary. The EIM will indicate a valid

connection to the Ethernet in the following ways:



The Ethernet LED maintains a solid green color when

connected to a 100 Mbps Ethernet network



The Ethernet LED maintains a solid orange color when

connected to a 10 Mbps Ethernet network



The Ethernet LED will flash when Ethernet packets are

being transmitted or received

LED Name LED Color LED Function

Ready

Red

Green

OFF

Steady ON: Power is on and the EIM

is booting.

Blinking: Indicates an IP Conflict

Steady ON: Power is on and the EIM

is functioning normally

Power is OFF or power error

condition exists.

Link

Orange

Green

OFF

10 Mbps Ethernet Connection

100 Mbps Ethernet Connection

Ethernet cable is disconnected or has

a short.

Tx/Rx

Orange

Green

OFF

Serial port is receiving data

Serial port is transmitting data

No data is being transmitted or

received through the serial port.

Reset Button

There is an onboard reset button located between the

power connection and Ethernet connection on the EIM.

Press the Reset button continuously for 5 seconds to

load factory defaults: Use a pointed object, such as a

straightened paper clip or toothpick, to press the reset

button.

This will cause the Ready LED to blink ON and OFF. The

factory defaults will be loaded once the Ready LED stops

blinking (after about 5 seconds). At this point, you should

release the reset button.

It is possible to limit the reset function for the first 60

seconds from initial power-up by accessing the Basic

Settings screen in the webserver configuration mode and

selecting the “Yes” option for Reset Button Protect.

Page is loading ...

9

Raccordement du MIE au panneau de commande de l’éclairage

Module d’interface Ethernet

35. À l’écran de confirmation des paramètres de

fonctionnement, sélectionnez le bouton Enregistrer/

redémarrer.

36. Fermez le navigateur Web lorsque l’écran Enregistrer/

redémarrer avec le bouton apparaît. La configuration est

maintenant terminée.

N’oubliez pas de restaurer les paramètres réseau TCP/IP à

leur configuration d’origine. S’il est nécessaire de rétablir la

connexion à partir des pages du serveur Web, assurez-vous

que l’ordinateur est configuré pour communiquer par le

même sous-réseau que l’appareil de MIE. Au lieu d’entrer

l’adresse par défaut du navigateur, il faudra utiliser l’adresse

IP attribuée à l’appareil.

Raccordement du MIE au panneau de com-

mande de l’éclairage

Une fois la configuration terminée, il est nécessaire de

raccorder l’appareil au panneau de commande de l’éclairage

et suivant les étapes suivantes:

1. Branchez le câble série de style téléphonique dans

l’adaptateur femelle à 9 broches fourni.

2. Branchez la tête de l’adaptateur à 9 broches au port

série du module d’interface au Ethernet.

3. Branchez l’autre extrémité du câble de communication

de style téléphonique au port de communications de

style RJ11 du panneau de commande de l’éclairage.

(Certains régulateurs possèdent deux ports de style

RJ11. Il faut brancher le câble au connecteur portant

l’étiquette RS-232.)

4. Branchez une extrémité du câble Ethernet au port RJ45

du module d’interface Ethernet et l’autre extrémité du

câble au réseau Ethernet.

5. Branchez le bloc d’alimentation fourni avec l’appareil.

ADJ

LCD

RSC POWERRSC LINK

ICD LINK

VCC

GND

TCK

TDO

TDI

TMS

JTAG

TEST

16

32

15

31

14

30

13

29

12

28

11

27

10

26

9

25

8

24

7

23

6

22

5

21

4

20

3

19

2

18

CH

1CH

17CH

ON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSO

PWR

NET+NET

REM

GND+24

REM

LOCAL

PCI-NET

DIGITA

PCI-NETPCI-NET

RS-232

NET

POWER

LSC

TERM

CAN-TX CAN-RX

RESET

50-022180-02

C

PCI 2005

STATUSNE T

54-022180-

ANALOG COMAN1AN2AN3AN4

ANALOGS

CW

TP1

TB2

J10

J9

C43

TB1

LED2

LED6

LED3

SR1

IND1

C29

J8

J4

J5

J2

LED4 LED5

J6

J3

LED1

J7

J1

D6D5D4D3

TB3

CONCENTRATEUR

LAN de l'immeuble

Logiciel de commande d’éclairage

Le module d'interface Ethernet (MIE) peut être raccordé à

n'importe quel régulateur du réseau.

Adaptateur de CA

Câble de style

téléphonique RS-232

avec tête d'adaptateur

Réseau RS-485

versles autres

panneaux

de commande

de l'éclairage

Interface Ethernet

Module (MIE)

Page is loading ...

14

Conexión del EIM con el panel de iluminación

Del software de interfaz de Ethernet

14. En la pantalla de aceptación de Configuraciones de

funcionamiento, seleccione el botón Guardar/Reiniciar.

15. Una vez que aparezca la pantalla de aceptación

Guardar/Reiniciar, cierre el explorador web. Ya está

completa la configuración.

Recuerde reestablecer las configuraciones TCP/IP de la red

de su computadora a sus configuraciones originales. Si

necesita volver a conectarse a través de las páginas web

del servidor, deberá asegurarse de que su computadora

esté configurada para comunicarse en la misma subred

del dispositivo EIM. En vez de escribir la dirección

predeterminada en la dirección del explorador, deberá

utilizar la dirección IP asignada de la unidad.

Conexión del EIM con el panel de iluminación

Una vez que la configuración esté finalizada, será necesario

conectar el dispositivo al panel del control de iluminación,

por medio de los siguientes pasos:

1. Conecte el cable de comunicaciones de estilo

telefónico incluido al cabezal adaptador de 9 clavijas

provisto.

2. Conecte el cabezal adaptador de 9 clavijas al puerto

serial del módulo de interfaz de Ethernet.

3. Conecte el otro extremo del cable de comunicaciones

estilo telefónico al puerto COM estilo RJ11 en el panel

del control de iluminación. (En algunos controladores,

hay dos conectores estilo RJ11. Conecte el cable con el

conector etiquetado como RS-232.)

4. Conecte un extremo del cable Ethernet al puerto RJ45

del módulo de interfaz de Ethernet, y el otro extremo

del cable a la red Ethernet.

5. Enchufe el adaptador de alimentación incluido con el

dispositivo.

ADJ

LCD

RSC POWERRSC LINK

ICD LINK

VCC

GND

TCK

TDO

TDI

TMS

JTAG

TEST

16

32

15

31

14

30

13

29

12

28

11

27

10

26

9

25

8

24

7

23

6

22

5

21

4

20

3

19

2

18

CH

1CH

17CH

ON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSOON +24 OFF LSO

PWR

NET+NET

REM

GND+24

REM

LOCAL

PCI-NET

DIGITA

PCI-NETPCI-NET

RS-232

NET

POWER

LSC

TERM

CAN-TX CAN-RX

RESET

50-022180-02

C

PCI 2005

STATUSNET

54-022180-

ANALOG COMAN1AN2AN3AN4

ANALOGS

CW

TP1

TB2

J10

J9

C43

TB1

LED2

LED6

LED3

SR1

IND1

C29

J8

J4

J5

J2

LED4 LED5

J6

J3

LED1

J7

J1

D6D5D4D3

TB3

CONCENTRADOR

LAN del edificio

Software del control de iluminación

El EIM puede conectarse con cualquier controlador en la red.

Adaptador de CA

Cable estilo telefónico

RS-232con cabezal

de cable adaptador

Red RS-485 con

otros paneles

de control de

iluminación

Interfaz Ethernet

Módulo (EIM)

Page is loading ...

Eaton

1000 Eaton Boulevard

Cleveland, OH 44122

United States

Eaton.com

Eaton’s Cooper Controls Business

203 Cooper Circle

Peachtree City, GA 30269

CooperControl.com

Printed in USA

P/N: 9850-000436-00

Eaton is a registered trademark.

All trademarks are property

of their respective owners.

Eaton est une marque de commerce

déposée. Toutes les autres marques

de commerce sont la propriété de leur

propriétaire respectif.

Eaton es una marca comercial

registrada. Todas las marcas comerciales

son propiedad de sus respectivos

propietarios.

WARRANTIES AND LIMITATION OF LIABILITY

Please refer to www.coopercontrol.com under the Legal section for our terms and conditions.

GARANTIES ET LIMITATION DE LA RESPONSABILITÉ LÉGALE

Veuillez consulter la section juridique de www.coopercontrol.com pour connaître nos conditions générales

GARANTÍAS Y LIMITACIONES DE RESPONSABILIDAD CIVIL

Remítase a la sección Legal del sitio web www.coopercontrol.com para conocer nuestros términos y condiciones.

Cooper Lighting Ethernet Interface Module, EIM Installation guide

Cooper Lighting Ethernet Interface Module, EIM Installation guide

in other languages

Related papers

Other documents