2. Webasto
  3. DBW 2010
DBW 2010

Webasto DBW 2010 Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Webasto DBW 2010 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Webasto Product N.A., Inc. • 15083 North Road • Fenton, Michigan 48430
For Technical Assistance in USA Call: (800) 555-4518 • In Canada Call: (800) 667-8900
Visit us on the Web at: www.techwebasto.com (North America) www.webasto.com (Global)
Org. 01/2007 • Doc. Ident. FMTV
Page 1 of 2
Webasto Heater Operation
January 2007
Webasto Heater Operating Instructions for
FMTV
System Description
Both systems, factory or field installed, utilize the Webasto
DBW 2010 coolant heater to pre-heat the vehicle engine
for cold starting, and provide additional heat to the crew
compartment during vehicle operation.
The Webasto heater is located inside a protective
enclosure on the driver’s side of the vehicle, near the
engine exhaust outlet. See Figures 1. and 2. for heater
location.
– (1) Factory installed heater enclosure box
– (2) Vehicle exhaust outlet
– (3) Heater retrofit kit enclosure box
Factory Installed System Preparation
ATTENTION
Before starting the heater, it is important to remove and
relocate the 2 plugs in the bottom of the enclosure box.
Remove and relocate the air intake and exhaust plugs as
shown in Figure 3.
– (4) Heater air intake
– (5) Heater exhaust outlet
– (6) Heater exhaust plug (relocated)
– (7) Heater air intake plug (relocated)
FIGURE 1. FACTORY INSTALLED SYSTEM
FIGURE 2. FIELD INSTALLED (RETROFIT) SYSTEM
FIGURE 3. FACTORY INSTALLED STORAGE PLUGS
2
1
3
2
4
5
6
7
Webasto Product N.A., Inc. • 15083 North Road • Fenton, Michigan 48430
For Technical Assistance in USA Call: (800) 555-4518 • In Canada Call: (800) 667-8900
Visit us on the Web at: www.techwebasto.com (North America) www.webasto.com (Global)
Org. 01/2007 • Doc. Ident. FMTV
Page 2 of 2
Webasto Heater Operation
January 2007
Switching The Webasto Heater On (Factory
Installed System)
To switch the heater “On”, simply activate the switch
located on the instrument panel.
– (1) Instrument panel
– (2) Heater (On/Off) switch
Switching The Webasto Heater On (Field
Installed Heater System)
ATTENTION
The vehicle heat control knob must be in the heat mode
(pulled out).
To switch the heater “On”, simply activate the toggle
switch located on the instrument panel.
– (3) Vehicle heat control knob
– (4) Instrument panel
– (5) Heater (On/Off) switch
Switching The Webasto Heater Off
ATTENTION
Forgetting to switch the heater “off” when the vehicle
is parked (and not running) may result in dead batteries.
For either system, to switch the Webasto heater Off,
simply put the switch in the “Off” position. A cool down
cycle of approximately 3 minutes will occur, and the
Webasto heater will be off.
FIGURE 4. FACTORY INSTALLED ON/OFF SWITCH
FIGURE 5. RETROFIT KIT ON/OFF SWITCH
1
2
3 4
5
For installation instructions, parts manuals, troubleshooting etc. go to www.techwebasto.com or dial 1-800-432-8371.
/