Barco 72" Rear Projection System for iQ (Pro) Series Installation guide
- Category
- Projection screens
- Type
- Installation guide
This manual is also suitable for
BARCO PROJECTION
72” REAR PROJECTION STRUCTURE FOR IQ
R9842250
INSTALLATION MANUAL
06082003 R5976655/00
Barco nv Intelligent Displays
Noordl
aan 5, 8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.35.86.51
E-mail:
Visit us at the web: www.barco.com
Printed in Belgium
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of BARCO.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufactures.
Table of contents
TABLE OF CONTENTS
1. Safety..................................................................................................................3
1.1 Safetyinstructions ...................................................................................................................... 3
2. Packageofthe72" rearstructure................................................................................5
2.1 Unpackingthe72"rearstructure....................................................................................................... 5
3. Mountinginstructions ..............................................................................................7
3.1 Mountingthebaseassembly........................................................................................................... 7
3.2 MountingtheTopassembly ............................................................................................................ 9
3.3 Baseandtopassembling..............................................................................................................10
3.4 MountingtheMirror....................................................................................................................13
3.5 Mountingtheprojector.................................................................................................................14
3.6 Preparingthescreen...................................................................................................................16
3.7 Mountingthescreen...................................................................................................................16
Index......................................................................................................................19
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003 1
Table of contents
2 R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
1. Safety
1. SAFETY
1.1 Safety instructions
Some operations in this manual require two persons to be executed safely.
This frame is designed for u se only with the Barc o iQ series projectors. Use with other appliances may result
in instabilit y
causing possible inju r y.
Follow the instructions thoroughly.
Improper installation ma y result in serious personal injury
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003 3
1. Safety
4 R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
2. Package of the 72" rear structure
2. PACKAGE OF T HE 72" REAR STRUCTURE
2.1 Unpacking the 72" rear structure
How to unpack the assembly
1. see procedure
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
5
2. Package of the 72" rear structure
6 R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
3. MOUNTING INSTRUCTIONS
Overview
A
B CDEF
Image 3-1
Figure Description Use Page
A hammer bolt + hexagonal nut
for all BVS profile fixations
page 7
page 9
page 10
page 13
B M8 x 16 bolt and nut
- projector plate fixation
- projector fixation
page 14
C
M8 x 25 bolt and nut
screen fixation
page 16
D M6 x 20 bolt
E
screw + nut
frame fixation on the screen
F
screw
frame fixation
3.1 Mounting the base assembly
Necessary tools
nut runner
Necessary parts
• long bars (2x)
• short bars (2x)
• pre-mounted U-shaped assembly (2x)
• pre-mounted assembly (1x)
• hammer bolts and nu
ts (A)
How to mount the bas
e assembly ?
1. Place the parts as shown on the image (image 3-2)
See image 3-3.
2. Tighten the parts using the hammer bolts and nuts.
3. Mount the screen supporting parts using the hammer bolts and nuts.
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
7
3. Mounting instructions
Image 3-2
Image 3-3
8 R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
3.2 Mounting the Top assembly
Necessary tools
nut runner
Necessary parts
• long bars (6x)
• pre-mounted square parts
• hammer bolts and nuts (A)
How to mount the top assembly ?
1. Place the parts as shown on the image (image 3-4)
2. Tighten the parts using the hammer bolts and nuts (image 3-5)
Image 3-4
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003 9
3. Mounting instructions
Image 3-5
3.3 Base and top assembling
How to mount the top assembly on the base assembly ?
1. Place the top assembly on the base assembly, place the mounting guides so as to be in front of the base assembly part. (im-
ag
e 3-6, image 3-7)
2. Tighten the parts using the hammer bolts and nuts (image 3-8)
10
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
Image 3-6
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003 11
3. Mounting instructions
Image 3-7
Image 3-8
12 R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
3.4 Mounting the Mirror
Necessary tools
nut runner
Necessary parts
•mirror
• hammer bolts and nuts (A)
To prevent risks of injury, the mounting of the mirror has to be done by 2 persons.
What has to be done ?
The mirror has to be mounted on the assembly. This is done by means of three fixation points
STEP 1
STEP 2
Image 3-9
How to mount the mirror ?
1. Hookthemirrorinthetopassembly.Uset
he upper slot. (image 3-10)
2. Fix the bottom of the mirror to the transversal bar using a hammer bolt and nut (image 3-11)
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
13
3. Mounting instructions
Image 3-10
Image 3-11
3.5 Mounting the projector
What has to be done ?
The projector has to be mounted in the frame.
Prior to that, the plate supporting the projector must be fixed.
The plate is fixed at 2 positions:
1. at the top by 2 pre-mounted fixation profiles
1. at the bottom using 2 pre-mounted short bars and fixation profiles.
STEP 1
STEP 2
Image 3-12
The Projector itself is mounted on the plate using three bolts and nuts turned in the three projector feet
14
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
3. Mounting instructions
Necessary tools
nut runner
Necessary parts
• projector support plate
• bolts and nuts (B)
• Barco iQ projector
• Barco iQ projector feet
How to mount the projector plate ?
1. Fix the plate on the previously mounted short bars using the M8 bolts and nuts. (image 3-13)
2. Fix the plate on the upper fixation profiles using the M8 bolts and nuts (image 3-14)
Image 3-13
view of the bottom fixation of the projector support plate
A previously mounted short bar
B bolt (B)
Image 3-14
How to mount the projector ?
1. If necessary, remove plastic covers of the feet
2. If necessary, mo
unt the 3 feet on the projector
3. Turn the 3 bolts in the feet
4. Place the projector on the plate by hooking the bolts in the three plate holes
5. Secure the position by tightening the bolts (image 3-15)
Image 3-15
projector mounted on the plate
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003 15
3. Mounting instructions
3.6 Preparing the screen
What has to be done ?
A frame has to be mounted on the screen
How to mount the wooden frame onto the screen ?
1. mount the lateral plate on the screen using the screws and nuts (E)
2. Fix the lateral plates to the bottom plate using the screws (F) (image 3-16)
E
F
Image 3-16
3.7 Mounting the screen
What has to be done ?
How to mount the screen ?
1. Place the screen as shown on the image, the bottom must be positioned on the previously mounted arms (A). (image 3-17)
2. Fix the bottom part by tightening the bolt (image 3-18)
3. Fix the upper part by using the M8 x 25 bolt (image 3-19)
16
R5976655 72” REAR PROJECTION STRUCTURE FOR IQ 06082003
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
Barco 72" Rear Projection System for iQ (Pro) Series Installation guide
- Category
- Projection screens
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco OverView cPU67-DL Installation guide
-
-
Barco OverView cDG67-DL Installation guide
-
-
-
-
-
-
-