![](//vs1.manuzoid.com/store/data-gzf/be33d2ffea60fb037b5405ed203352dd/2/001952732.htmlex.zip/bg2.jpg)
5019 401 05135
Add the detergent as described in the chapter
Detergent and Additives in the instructions
for use.
1. Turn the programme selector knob in any
direction to the desired programme.
The light above the Start button flashes.
2. The programme sequence indicator and the
indicator with the maximum possible spin
speed light up.
Easy Ironing button
To lessen creasing, the water quantity is
increased and the clothes are spun very gently
at reduced power. This makes your laundry
significantly damper at the end of the
programme.
Prewash button
Only for heavily soiled laundry (e.g. sand or
granular dirt). Programme duration is
increased by some 15 min.
Intensive Rinse button
An additional rinse cycle is carried out.
This option is particularly suitable for areas
with very soft water, washing baby linen
and helps people with detergent allergies.
Rinse Hold button
The laundry remains in the last rinse water
without being spun: discoloration of the
laundry and additional creasing are
prevented.
This option is particularly recommended for
the programme Synthetics or Delicates.
This function is particularly useful if you
want to postpone spinning to a later time.
Note: The programme has reached the Rinse
Hold when the corresponding light flashes.
Terminate the Rinse Hold option:
Press the Rinse Hold button again; the
programme will terminate automatically
with the appropriate spin cycle for the
current programme.
If you do not wish to spin the clothes, turn
the programme selector knob to Drain
and press the Start button again.
CONSUMPTION DATA
*
Programme Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Programme
duration
approx.
(hours : minutes)
Cotton
95 6.0 54 1.9 2:00
Cotton
60 6.0 49 1.14 2:30
Cotton
40 5.0 47 0.7 2:05
Daily Mixed
40 3.0 48 0.55 1:00
Chrono 30`
30 3.0 37 0.3 0:30
Synthetic
60 2.5 45 0.8 1:35
Synthetic
40 2.5 45 0.5 1:20
Delicate
30 1.5 60 0.5 0:45
Wool
40 1.0 60 0.5 0:40
Handwash
30 1.0 45 0.4 0:35
*The
consumption values
were measured in normalized conditions in compliance with Standard
IEC 60456.
** The
programme duration
may also vary from the chart values. The washing machine is able to allow for
particular household conditions and to adapt the programme run time accordingly.
*** To reduce the
water temperature
, some cold water is added at the end of the main wash cycle, before
the pump drains the water out.
POUR IN DETERGENT, CLOSE THE
DOOR AND SELECT A PROGRAMME
SELECT SPECIAL OPTIONS -
The corresponding lights go on
(if not selectable: rapid flashing for
3seconds)
Speed Reduction button
A maximum spin speed is assigned to each
programme.
Press the button to set another speed for
the spin cycle.
If no light goes on, the final spin is
cancelled. The water is only drained out.
With the Start Delay function the appliance
can be run cheaply e.g. at night, when the
electricity is cheaper.
Press the Start Delay button. Select the
programme start from 3 to 12 hours ahead
by pressing the button again.
Press the Start button.
The Start Delay indicator light flashes until
the programme starts.
Start Delay correction.
Before the Start Delay has been started:
The preset number of hours can be altered by
continuously pressing the Start Delay button.
By pressing the Start Delay button again
after the 12 setting, the time delay can be
deleted again or set again.
After the Start Delay has been started:
The preset number of hours can be reduced by
pressing the Start Delay button again;
please note, however, that the washing
programme starts IMMEDIATELY, as soon as
you activate it again with the Start Delay
switch 3 setting. To increase the number of
hours preselected, first turn the programme
selector switch to the Off position. Then set
the programme and the additional options
again and select the desired number of hours.
After you have selected the programme and
the additional option, the indicator light over
the Start button flashes. Turn on the tap
and start the programme by pressing the
Start button. Now the indicator light above
the button goes on.
In addition, all programme phases are
indicated by the associated lights. After the end
of a programme phase, the associated indicator
light goes out. Thus the programme sequence
indicator moves from left to right across the
wash, rinse and spin phases. At the end of the
programme, only the End (Fin) indicator is
still on.
As long as a washing programme is running,
the lamp lights up to show that the door
cannot be opened. When the lamp goes off,
the door can be opened again.
If Start has been pressed, but the door is not
latched, the Door Locked indicator flashes
for 10 seconds. The door must be pushed shut
within this time. After the 10 seconds, the
Door Locked indicator goes out and the
Start button flashes. The door must then be
opened and closed again and the Start
button must be pressed.
Pump
Waste water is not pumped out. Check wether
the drain hose is kinked or the filter must be
cleaned; in the latter case refer to the
Instructions for Use (Removing the Filter).
Water Tap
The appliance has no or insufficient water
supply. Open the water tap; if the indication
still lights up, refer to the Troubleshooting
Guide in the Instructions for Use.
The End (Fin) indicator goes on.
1. Set the programme selector knob to the
Off position.
2. Turn off the tap.
3. Open the door and unload the machine.
A newly-selected programme will continue in
the same programme section during which the
current programme was interrupted. Therefore
do not add any more detergent.
1. Press the Start button to interrupt the
programme. The light flashes.
2. Select the new programme (with
temperature), any additional options and - if
you wish - another spin speed.
3. Press the Start button again to restart the
programme.
If you are in the Prewash programme step,
this additional option cannot be deselected
as described (to do this see Cancel (Reset) a
running programme before the end).
Press the Reset (Cancelar) button for at
least 2 seconds. Any existing water is
drained out before the door can be opened.
START DELAY
PROGRAMME START
DOOR LOCKED INDICATOR
TROUBLE INDICATORS
PROGRAMME END
RESELECT AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
4gb05135.fm Page 2 Monday, March 22, 2004 12:18 PM
Black process 45.0° 100.0 LPI