Arcam DVD Player DV79 User manual

Brand: Arcam

Model: DVD Player DV79

Category: DVD players

Type: User manual

This manual is also suitable for

DV79

DV79HANDBOOK/MANUEL/HANDBUCH/HANDLEIDING

Arcam DV79 DVD player

Lecture de DVD Arcam DV79

DVD-Spieler Arcam DV79

Arcam DV79 DVD-Speler

English

Français

Deutsch

Nederlands

DV79

E-2

English

DV79

E-3

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

ATTENTION

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing

to qualied service personnel.

WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.

The lightning ash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated

‘dangerous voltage’ within the product’s enclosure that may be of sufcient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

CAUTION: In Canada and the USA, to prevent electric shock, match the wide blade of the plug to the wide slot in the socket and

insert the plug fully into the socket.

Safety guidelines

Important safety instructions

This product is designed and manufactured to meet strict

quality and safety standards. However, you should be aware

of the following installation and operation precautions:

1. Take heed of warnings and instructions

You should read all the safety and operating instructions

before operating this appliance. Retain this handbook for

future reference and adhere to all warnings in the handbook

or on the appliance.

2. Water and moisture

The presence of electricity near water can be dangerous. Do

not use the appliance near water – for example next to a

bathtub, washbowl, kitchen sink, in a wet basement or near

a swimming pool, etc.

3. Object or liquid entry

Take care that objects do not fall and liquids are not

spilled into the enclosure through any openings. Liquid

lled objects such as vases should not be placed on the

equipment.

4. Ventilation

Do not place the equipment on a bed, sofa, rug or similar

soft surface, or in an enclosed bookcase or cabinet, since

ventilation may be impeded. We recommend a minimum

distance of 50mm (2 inches) around the sides and top of the

appliance to provide adequate ventilation.

5. Heat

Locate the appliance away from naked ames or heat

producing equipment such as radiators, stoves or other

appliances (including other ampliers) that produce heat.

6. Climate

The appliance has been designed for use in moderate

climates.

7. Racks and stands

Only use a rack or stand that is recommended for use with

audio equipment. If the equipment is on a portable rack it

should be moved with great care, to avoid overturning the

combination.

8. Cleaning

Unplug the unit from the mains supply before cleaning.

The case should normally only require a wipe with a soft,

damp, lint-free cloth. Do not use paint thinners or other

chemical solvents for cleaning.

We do not advise the use of furniture cleaning sprays or

polishes as they can cause indelible white marks if the unit

is subsequently wiped with a damp cloth.

9. Power sources

Only connect the appliance to a power supply of the type

described in the operating instructions or as marked on the

appliance.

10. Power-cord protection

Power supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords and plugs,

and the point where they exit from the appliance.

11. Grounding

Ensure that the grounding means of the appliance is not

defeated.

12. Power lines

Locate any outdoor antenna/aerial away from power lines.

13. Non-use periods

If the unit has a stand-by function, a small amount of

current will continue to ow into the equipment in this

mode. Unplug the power cord of the appliance from the

outlet if left unused for a long period of time.

14. Abnormal smell

If an abnormal smell or smoke is detected from the

appliance, turn the power off immediately and unplug the

unit from the wall outlet. Contact your dealer immediately.

15. Servicing

You should not attempt to service the appliance beyond that

described in this handbook. All other servicing should be

referred to qualied service personnel.

16. Damage requiring service

The appliance should be serviced by qualied service

personnel when:

A. the power-supply cord or the plug has been damaged,

B. objects have fallen, or liquid has spilled into the

appliance, or

C. the appliance has been exposed to rain, or

D. the appliance does not appear to operate normally or

exhibits a marked change in performance, or

E. the appliance has been dropped or the enclosure

damaged.

Safety compliance

This product has been designed to meet the IEC 60065

international electrical safety standard.

DV79

E-2

English

DV79

E-3

Safety guidelines ............................................... E-2

Important safety instructions ............................ E-2

Safety compliance ........................................... E-2

Before you start!................................................ E-4

Using this handbook ........................................ E-4

What’s in the box? ...........................................E-4

Inserting the batteries into the remote control..... E-4

Disc types supported........................................ E-5

HDMI digital interface....................................... E-5

Positioning the unit .......................................... E-6

Connecting the video output ............................. E-6

Installation ........................................................ E-6

Connecting the digital-audio output....................E-7

Connecting the analogue-audio output ............... E-7

The remote-control input.................................. E-7

Connecting to a power supply ........................... E-7

Basic use of your DVD player ............................. E-8

Introduction.................................................... E-8

Front-panel controls......................................... E-8

Playing a disc.................................................. E-8

The HDMI interface ............................................ E-9

About HDMI ................................................... E-9

Connecting using HDMI .................................... E-9

Troubleshooting...............................................E-9

Using the CR-415 remote control ..................... E-10

Advanced controls (CR-415) ............................ E-11

Conguring your DVD player............................ E-12

Introduction.................................................. E-12

Obtaining a picture ........................................ E-12

Using the Set-up menus ................................. E-12

Operational set-up......................................... E-13

Video set-up ................................................. E-14

Audio set-up ................................................. E-15

Speaker set-up.............................................. E-16

Delay set-up ................................................. E-17

Trim set-up................................................... E-18

Access set-up................................................ E-18

Completing the set-up.................................... E-18

Advanced DVD and VCD features ..................... E-19

Jumping to a particular point........................... E-19

Special playback modes.................................. E-19

Advanced MP3/WMA/JPEG and audio-CD

features ........................................................... E-21

Screen layout................................................ E-21

Player mode.................................................. E-21

Shufe and Repeat ........................................ E-23

Remote-control codes ...................................... E-24

Technical specications ................................... E-25

Guarantee ........................................................ E-26

On line registration .......................................... E-26

Appendix: Serial programming interface.......... E-27

Introduction.................................................. E-27

Command and response formats ..................... E-27

Command Specications................................. E-29

Contents

The small print:

This product incorporates copyright protection technology that

is protected by method claims of certain U.S. patents and other

intellectual property rights owned by Macrovision Corporation and

other rights owners. Use of this copyright protection technology

must be authorized by Macrovision Corporation, and is intended

for home and other limited viewing uses only unless otherwise

authorized by Macrovision Corporation. Reverse engineering or

disassembly is prohibited.

Consumers should note that not all high denition television sets

are fully compatible with this product and may cause artifacts

to be displayed in the picture. In case of 525/625 progressive

scan picture problems, it is recommended that the user switch

the connection to the ‘Standard Denition’ output. If there are

questions regarding TV set compatibility with this model 525/625p

DVD player, please contact your dealer or the Arcam Customer

Support Department.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, “MLP Lossless”, and the double-D symbol are

trademarks of Dolby Laboratories.

Manufactured under license from Digital Theater Systems,

Inc. U.S. Pat. No. 5,451,942; 5,956,674; 5,974,380; 5,978,762;

6,226,616; 6,487,535 and other U.S. and world-wide patents

issued and pending.

“DTS” and “DTS Digital Surround” are trademarks of Digital

Theater Systems, Inc.

Reserved.

HDMI, the HDMI logo and High-Denition Multimedia Interface

are trademarks or registered trademarks of HDMI Licensing LLC.

DV79

E-4

English

DV79

E-5

Before you start!

Using this handbook

This handbook has been designed to give you all the information you need to install, connect, set-up and

use the Arcam DiVA DV79. The remote control handset supplied with the equipment is also described.

It may be that the DV79 has been installed and set-up as part of your Hi-Fi installation by a quali ed

Arcam dealer. In this case, you may wish to skip the sections of this handbook dealing with installation

and setting up the unit, and move directly to the sections dealing with using the player. Use the contents

list on page 3 to guide you to these sections.

Safety

Safety guidelines are set out on page 2 of this handbook.

Many of these items are common sense precautions, but for your own safety, and to ensure that you do

not damage the unit, we recommend that you read them. This is a class 1 product and requires an earth

connection.

What’s in the box?

Please con rm that the following items are in the box when you receive it:

Arcam DV79 DVD player — the model number is shown on the right of the front panel of the

player;

Arcam CR-415 remote control with 2 ‘AAA’ batteries — the remote control model number is

shown on the front at the bottom of the remote control;

Mains power lead appropriate for the mains supply in your area;

Product registration card and envelope.

If any of these items are missing or incorrect, please contact your Arcam dealer immediately.

Inserting the batteries into the remote control

The remote control requires 2 ‘AAA’ batteries to operate. To insert the batteries

into the remote control, please follow these instructions:

1. Open the battery compartment cover on the back of the remote control.

2. Insert two AAA batteries into the battery compartment, following the

polarity indications given inside the compartment itself.

3. Close the cover.

Notes on inserting the remote control batteries

Incorrect use of batteries can result in hazards such as leakage and

bursting.

Do not mix old and new batteries together.

Do not use different kinds of battery together—although they may look

similar, different batteries may have different voltages.

Ensure that the plus (+) and minus (—) ends of each battery match the

indications in the battery compartment.

Remove batteries from equipment that is not going to be used for a

month or more.

When disposing of used batteries, please comply with governmental (or

other) regulations that apply in your country or area.

Using the remote control

Please keep in mind the following when using the remote control:

Ensure that there are no obstacles between the remote control and the

remote sensor on the DV79. The remote has a range of about seven

meters. (If the remote sensor is obscured, the remote control input jack

on the rear panel is available. Please contact your dealer for further

information.)

Remote operation may become unreliable if strong sunlight or  uorescent

light is shining on the remote sensor of the DV79.

Replace the batteries when you notice a reduction in the operating range

of the remote control.





A. Open the cover of the remote control

battery compartment

B. Insert the batteries into the remote

control





C. Close the cover of the remote control

battery compartment

DV79

E-4

English

DV79

E-5

Disc types supported

The ARCAM DV79 DVD-player plays a range of disc types. Discs entered into the DV79 should bear one

of the logos shown on the right. These disc types include:

DVD-video (single region, set at factory);

DVD-audio;

CDDA (‘normal’ audio-CDs) including HDCD decoding, CD-R, and CD-RW;

Video CD, including variants such as CVCD, SVCD and DVCD;

MP3 and WMA audio les, when on a CD-ROM or CD-R/CD-RW (some restrictions apply);

Picture CDs (JPEG image les).

Other disc formats may not play correctly in this player.

DVD-R/RW and CD-R/RW discs (Audio CDs and Video CD/Super VCDs) recorded using a DVD recorder,

CD recorder or personal computer may not play in the DV79. This may be caused by a number of

possibilities, such as the type of disc used and the type of recording.

CD-R/RW compatibility

This unit will play CD-R and CD-RW discs recorded in CD Audio or Video CD/Super VCD format,

or as a CD-ROM containing MP3/WMA audio les, or as a ‘Kodak’ Picture CD. However, any other

content may cause the disc not to play, or create noise/distortion in the output. This unit cannot

record CD-R or CD-RW discs.

Unnalized CD-R/RW discs recorded as CD Audio cannot be played.

DVD-R/RW compatibility

This unit will play DVD-R/RW discs that are recorded using the DVD Video format.

This unit cannot record DVD-R/RW discs.

Unnalized DVD-R/RW discs cannot be played in this player.

Compressed audio compatibility

The DV79 will play CD-ROM discs containing les saved in the MPEG1 Audio Layer 3 (MP3) and Windows

Media le (WMA) formats, with sampling rates of 44.1 or 48kHz. Incompatible les will not play correctly,

potentially causing noise or distortion on the audio outputs.

Fixed bitrate les are recommended. Variable bitrate (VBR) les are playable, but the playing

time may not be shown correctly.

The CD-ROM used to compile your MP3/WMA les must be ISO 9660 Level 2 compliant. CD

physical format: Mode1, or Mode2 XA Form 1.

This player plays only tracks that are named with the le extensions ‘.mp3’, ‘.MP3’, ‘.wma’ or

‘.WMA’.

This player is compatible with multi-session discs, but plays only sessions that are closed.

Use CD-R or CD-RW media for recording your MP3/WMA les.

There are many different recording bit rates available to encode your MP3/WMA les. See

page 22 for a list of bit rates that are compatible with this player. Note that MP3 audio encoded

at 128 Kbps or higher should sound close to regular CD Audio quality. This player will play lower

bitrate MP3 or WMA tracks, but be aware that the sound quality becomes noticeably worse at

lower bitrates.

PC created disc compatibility

If you record a disc using a personal computer, even if it is recorded in a ‘compatible format’ as

listed above, there will be cases in which the disc may not be playable in this machine due to the

setting of the application software used to create the disc. In these particular instances, check

with the software publisher for more detailed information.

Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information.

HDMI digital interface

The HDMI (High Denition Multimedia Interface) interconnect provides high-quality digital audio and

video, all through a single user-friendly connector. HDMI is the rst consumer-electronics interface

to support uncompressed standard, enhanced, or high-denition video together with stereo or multi-

channel surround-sound audio, all using one interface.

Connection to a HDMI-equipped AV receiver or audio-visual device for high-quality audio and video is

easy, and communication between the video source and (DTV) players, set-top boxes, and other audio-

visual devices occurs automatically.

For further information on HDMI, please see page 9.

DV79

E-6

English

DV79

E-7

Positioning the unit

Place the DV79 on a level,  rm surface and ensure that there is adequate ventilation for the unit.

Connecting the video output

To view the pictures from the DVD player you need to connect one of its video outputs to your display

device (TV, monitor, projector, etc.).

The DV79 has six video output options:

Component video

Composite video

RGB

Progressive scan component 525P (480P) and 625P (576P) video

S-video

HDMI digital video

You only need to use one type of video from the list; choose a type that your display device supports. If

your display device does not support any of the above connection types then you will be unable to use it

with the DV79; in this case, please contact your dealer for futher assistance.

Note that you may connect equipment such as AV receivers in the signal path between the DVD player

and the display device, so long that the connected equipment also supports the type of video signal you

intend to use. For instructions on how to connect AV equipment, consult the manual for that equipment.

NOTE: The DVD player supports either component video or RGB video at any one time, but not both.

This is speci ed in the set-up menu (see page 12). If you use either of these outputs with an incorrect

menu setting, no damage will occur but the picture will be coloured in a strange way. Similar effects

result from cross-connection of the three signals.

If you use component video outputs, you must ensure that the SCART socket is not used. Similarly, if

the SCART socket is used, disconnect the component video leads.

Composite video

If your display device offers only a composite input (sometimes labelled CVBS or just ‘video’), connect

this to the COMPOSITE video output of the DVD player using a 75Ω phono cable suitable for video use.

Note that a composite video connection gives the lowest quality output; if your display device supports

other video connection types, we advise that those are used instead.

S-Video

The S-Video output (also known as S-VHS or Y/C) is commonly supported by display devices worldwide.

Connect the S-VIDEO output of the DVD player to the S-Video input of the display device using an

appropriate cable.

Component video

Use three 75Ω phono cables to connect the Component Y, Pb, Pr

outputs of the DVD player to the Y, Pb, Pr inputs of the display

device. Ensure that the cables are suitable for video use and that

they are approximately the same length.

Some component video interfaces are labelled differently to the

DV79; see the table if the component inputs of your display device

are not labelled ‘Y, Pb, Pr’.

RGB/SCART output

RGB output is available on both the SCART and Component/RGB sockets and offers picture quality equal

to component video.

Use appropriate cables to connect either the SCART connector or RGB phonos to your display device.

Note that if you are using RGB output via phono connectors, you will also need to use the COMPOSITE

signal as a synchronisation signal.

Installation

SCART A/V OUT

POWER INLET

110/115/230V

PCM/BITSTREAM

COAX

OPTICAL

COMPOSITE

VIDEO

S-VIDEO

DIGITAL AUDIO OUT

1 2SUB RS

AUDIO OUT

SUPPLY

VOLTAGE

HDMI

RS232 UNMOD MOD

COMPONENT VIDEO

REMOTE IN

DIGITAL VIDEO OUT

ANALOGUE VIDEO OUT

DV79 alternative alternative alternative

Y Y Y Y

Pb Cb (B–Y) U

Pr Cr (R–Y) V

DV79

E-6

English

DV79

E-7

If you are using a SCART connection to your TV, and you do not wish to listen to the audio

through it, then it is best to mute your TV’s speakers as SCART also carries stereo audio signals;

muting the TV will prevent this audio being heard.

Note that the SCART output has a control signal that switches your TV to its SCART

input when the DV79 is turned on. It will also signal to wide-screen TVs the correct aspect ratio

(16:9 or 4:3), provided this feature is supported by the TV.

Progressive video

If your television is capable of accepting a progressively scanned (de-interlaced) video signal,

you may wish to use the progressive video output from the DV79.

To connect the progressive output of the DV79 to your display device, follow the instructions

above for connecting component video. If you are unsure whether your display device can accept

progressive video, please refer to its instruction manual or consult your dealer.

HDMI digital video

The HDMI connector offers uncompressed digital video transmission between the DV79 and the

display device, and provides the highest quality video output.

To use this video connection, you will require a HDMI or HDMI/DVI cable between the DV79 and the

display device. See page 9 for further details.

Connecting the digital-audio output

If you have an external surround-sound decoder, receiver or D-A converter that you wish to use with the

DVD player, then you will need to connect it using either a co-axial or optical lead. These digital outputs

provide PCM, Dolby Digital, DTS or MPEG multi-channel audio, depending on the source material. It is

also possible (via the set-up menu of the DV79) to set the digital output always to put 2-channel PCM

(stereo mix-down) out.

If possible, use the co-axial connection as this offers slightly better performance. Connect the co-axial

output of the DVD player to the digital audio co-axial input of the decoder/D-A converter or receiver

using a phono cable designed for digital audio interconnection.

Alternatively, connect the optical output of the DVD player to the optical input of the decoder/D-A

converter or receiver using a TOSLINK optical lead.

Connecting the analogue-audio output

If you wish to use the high quality D-A converters of the DV79, then you will need to use its

analogue audio outputs.

Two pairs of stereo outputs are provided (these are identical), labelled L (left) and R (right).

Connect one of these pairs to the input of your ampli er using a suitable pair of interconnect

cables. If required, the second set of audio outputs can be used to connect to a second ampli er

set-up for ‘multi-room’ use, or routed to a tape recorder for making recordings.

For 6-channel material, an additional four outputs are provided. Together with one pair of the

2-channel output connections, these should be connected (using suitable interconnect cables) to

the ‘multi-channel’ analogue input of your home cinema processor (the multi-channel input may

be labelled ‘DVDA’ or ‘SACD’). In this case, the additional 2-channel output pair may be used for

some other function, as suggested above (although when playing 6-channel material, only the

left and right channels of this material would be heard).

The remote-control input

The REMOTE IN input can be used to pass RC5 codes to the DV79 if it is installed in a position (or

system) where infrared cannot be used. If this is required, please contact your dealer for further

information. The DV79 can accept both modulated (at 36kHz) and unmodulated RC5 signals.

Connecting to a power supply

Mains lead

The appliance is normally supplied with a moulded mains plug already  tted to the lead. If for any

reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a

potential shock hazard when inserted into the mains socket.

Check that the plug supplied with the unit  ts your supply and that your mains supply voltage agrees

with the voltage setting (115V or 230V) indicated on the rear panel of the unit.

If your mains supply voltage or mains plug is different, or you require a new lead, please consult your

Arcam dealer.

Plugging in

Push the plug (IEC line socket) of the power cable supplied with the unit into the socket (POWER INLET)

in the back of the unit. Make sure it is pushed in  rmly.

Put the plug on the other end of the cable into your power supply socket and switch the socket on.

If no picture is visible,

ensure that your display

device is set to the

correct input.

If ‘black bars’ are shown

at the top and bottom

of the screen: you are

viewing a ‘widescreen’

formatted  lm via a 4:3

format display device.

If possible, change your

display device to show

16:9 format output.

If nothing is audible,

ensure that your audio

device (TV, ampli er,

etc.) is set to the

correct input. Check the

connections at both ends

and, if necessary, try an

alternative cable.

DV79

E-8

English

DV79

E-9

Basic use of your DVD player

Introduction

‘Basic operation’ explains how to play a DVD, CD or other type of disc. Note that it may be necessary to

con gure your player correctly for your system before optimum – or any – playback can be achieved.

Player con guration is described beginning on page 12.

More sophisticated features – such as special playback modes and programming jumps and playback

sequences – are described in the ‘Advanced features’ section, later in this handbook.

Front-panel controls

Switching on

Switch the unit on by pressing the POWER button. The status LED glows green when the unit is powered

up and red when in stand-by mode (stand-by is operated from the remote control).

Note that the remote control sensor is located on the right-hand side of the display window. Do not

obstruct this or the remote will not work.

Playing a disc

Loading a disc

Press LOAD on the front panel (or OPEN on the handset) and place the disc on the tray, with the play-

back side facing down (some discs are double sided, in which case the side labelled ‘side A’ should face

up to play side A).

Press LOAD on the front panel to close the tray. The disc loads after a pause of a few seconds.

Playing a disc

Many DVDs begin playing automatically, but some titles begin by displaying a menu. Select the menu

item ‘Play movie’ (or similar) using the cursor pad, then press OK to start playback.

For discs that do not play automatically (including CDs and VCDs), press PLAY.

Note that when playing DVDs, the drive mechanism operates at much higher speeds compared with CDs

and so may produce more noise when loading and playing initial chapters; this is normal.

Fast play

Press

on the front-panel or remote control to play fast forward or backwards. For DVDs, VCDs

and CDs the following speeds for fast playback are available: x2, x4, x8, x20, x60 and x100. Press the

button repeatedly to cycle through the different speeds. To resume normal playback speed, press PLAY.

Fast playback is not available for MP3/WMA discs.

Skipping chapters/tracks

To skip chapters (or tracks on a CD), press or .

When skipping back, the  rst button press takes you to the beginning of the current chapter. Pressing

the button again takes you to the start of the previous chapter.

Pausing playback

Press PAUSE on the front panel or

;

on the remote control to pause playback. To resume playback,

press PLAY on the front panel or

on the handset.

Stopping playback

Press the STOP button on the front panel or

on the remote control to stop playback.

When playing a DVD, pressing STOP once performs a ‘resume stop’. If you now press PLAY, playback

resumes from the point it was stopped.

If you press STOP twice, this is a ‘complete stop’, and playback resumes from the beginning of the disc.

Front panel menu navigation

If desired, it is possible to navigate disc and player menus using the front panel buttons; to this end, the

NAV button is provided.

Pressing the NAV button causes the player to enter ‘navigator’ mode, indicated by the ‘NAV MODE’ LED

being illuminated. In this mode, the front panel buttons take on the functions illustrated above each

button, for example the STOP and PAUSE buttons become and .

To exit navigtor mode, press the NAV button for a second time.

POWER

DV 7 9 DVD PL AYER

TRACK

PAUSESTOPPLAYLOAD

SETUP MENUTITLEOK

MODE

NAV

DVDA

DV79

E-8

English

DV79

E-9

The HDMI interface

If you have a HDMI- or DVI-equipped monitor or display, you can connect it to the DV79 using a HDMI

cable. The HDMI connector carries uncompressed digital video, as well as digital audio.

About HDMI

HDMI (High Denition Multimedia Interface) supports both video and audio on a single digital connection

for use with DVD players, digital TV, set-top boxes, and other AV devices. HDMI was developed to

combine the technologies of High-bandwidth Digital Content Protection (HDCP) and the Digital Visual

Interface (DVI) in one specication, with the addition of transmission of digital audio information; HDCP

is used to protect digital content transmitted to DVI-compliant displays.

HDMI has the capability to support standard (interlaced), enhanced, or high-denition video together

with stereo or multi-channel surround-sound audio. HDMI features include uncompressed digital video,

one connector (instead of several cables and connectors), and communication between the AV source

and AV devices.

Connecting using HDMI

If the HDMI connector is to be used, we recommend rst setting the ‘Output Priority’ item on the video

menu page to ‘HDMI/DVI’. This will give full ‘plug and play’ functionality. See page 14 for details on how

to do this.

Use a HDMI cable to connect the HDMI socket on this player to a HDMI socket on a compatible display

device or receiver. The arrow on the cable connector body should be face up for correct alignment with

the connector on the DV79. If the DV79 has been congured to ‘HDMI priority’, then the DV79 will

congure its video output automatically to match the capabilities of the attached HDMI device. If the

connection was successful, ‘HDMI’ or ‘DVI’ is shown briey via the on-screen display according to the

compatibility of the connected component.

NOTE: A HDMI connection can be made only with HDMI or DVI-equipped components compatible

with both DVI and HDCP. Note that if you choose to connect to a DVI device, you will need an adaptor

(HDMI to DVI) to do so; a DVI/HDCP connection, however, does not support audio signals.

If you require further information on the possibilities for connecting your DV79 to your DVI/HDMI

equipped display device, please contact your Arcam dealer.

Troubleshooting

Problems with video

NO VIDEO (BLANK SCREEN)

Check that the HDMI cable is connected correctly at both ends. If an HDMI-equipped A/V

receiver is in use, try connecting the DV79 directly to the display device, in order to isolate

where the fault may lie.

Check that the display device is set to display the HDMI input (i.e., has not been set to some

other video input, instead).

Check that the HDMI connector of the receiver and/or display device is enabled. See the user

handbook of the connected device for details on doing this.

Using an alternative video display device (e.g., connected via the composite video out), check

that the ‘Output Priority’ item on the Video page of the Set-up menu is set to ‘HDMI / DVI’. See

page 14 for details on how to do this.

Consult the user handbook of the display device to ensure that it can handle the output formats

provided by the DV79. The DV79 can provide the following: 720x480P (NTSC progressive scan),

720(1440)x480i (NTSC interlaced), 720x576P (PAL progressive scan) and 720(1440)x576i (PAL

interlaced). At least one of these must be supported by the connected device in order for it to

work with the DV79.

NO VIDEO (RANDOM NOISE)

Random noise will be displayed if the content-protection algorithm fails to authenticate the attached

device. This will occur, for example, if a DVI device that does not support HDCP (such as a computer

monitor) is connected to the DV79.

To attempt to isolate this problem, remove all discs from the DV79, the power-off both it and the

connected display device. Switch the display device on, then the DV79 – at this point, the idle logo of the

DV79 should be shown on the display device. If this is not the case, please check the items listed above

for a blank screen.

If the noise appears when a copy-protected disc (DVD) is played, then it is the authentication that is

failing. Please contact your dealer for further information.

Problems with audio

The audio provided by the HDMI connector is the same as that provided through the SPDIF socket. Note

that pure DVI devices (connections requiring a HDMI to DVI convertor cable) do not support audio via

this connection.

If you have a HDMI device, try setting the audio output to Audio item of the Set-up menu to ‘PCM/2 Ch.’;

it may be that the display device supports only 2-channel audio.

DV79

E-10

English

DV79

E-11

MODE

STATUS SRCH

ZOOM ANGLE SUBT PL

AUDIO TRIM TITLE RTN

RPT CLEAR

PROG

A–B

7 8

DISP

4 5 6

1 2

DVD

CR-415

SETUP

MEM

OPEN

Using the CR-415 remote control

DISP (display)

Dims or turns the DV79’s display on or off. Turning

the display off generally gives a slight improvement in

sound quality.

Pressing DISP once turns the display off; twice dims

the display. To restore the display to full brightness,

press DISP a third time.

A–B

This button enables you to repeat a selected

section from the disc (see page 19).

RPT (repeat)

Press RPT to cycle through the repeat play options.

CLEAR

Use CLEAR to clear a numeric  eld.

0–9 keypad

This allows direct access to individual tracks on audio

CDs. To select a track, press the corresponding keypad

button followed by OK. For tracks greater than 9, enter

the digits in sequence. For example, to play track 15,

press 1, then 5, then OK.

PROG (program)

You can program a selection of up to 20 chapters/tracks

from a disc to play in any order. Press PROG to access the

’Programme’ menu (see pages 20 and 22).

MUTE

Stops sound to the speaker outputs of certain Arcam

ampli ers.

Volume +/–

Adjusts the volume on Arcam remote-controllable

ampli ers.

Note that the volume (+/–) controls and MUTE button

have no effect on the audio output level of the DVD

players.

OPEN

Opens and closes the disc tray

Slow play

Press or on the remote control to play slow forward

or backwards. There are four speeds of slow playback:

1/5, 1/4, 1/3 and 1/2. Press the button repeatedly to

cycle through the different speeds. To resume normal

playback speed, press PLAY.

Note that slow play does not apply to audio CDs.

Cursor pad and OK button

Use the cursor pad to navigate the On-Screen Display

(OSD) and menu pages. Con rm your selection with the

OK button.

Playback control

Pause (

;

), Play (

) and Stop (

)

(see page 8).

Fast play and Skip chapter/tracks

Play fast (

) and Skip (

) chapters/tracks in

both directions (see page 8).

Advanced controls

These buttons are described on the next page.

Standby

Press Standby to toggle the standby state of the DVD

player. Note that Arcam CD players are not controlled by

this button.

Press MENU to access the DVD ‘Disc’ menu.

This navigation menu is speci c to a disc and varies for

each title, but typically offers facilities to select chapters,

languages, and view extra material such as trailers or

documentaries.

Once the menu has been accessed, use the cursor pad to

move around the menu and press OK to activate a menu

‘button’.

SETUP

‘Setup’ allows you to con gure the DV79

for use in your system. Ensure that no disc

is playing and press SETUP to access the

‘Setup’ menu.

If the player does not respond

consistently to the remote

control, ensure that the player

is con gured to respond to the

correct remote control type; this is

done via the player set-up menu.

See page 12 for further details.

If the remote control receiver

(located on the right of the front-

panel window) is not ‘visible’ to the

remote control hand-set, then the

remote control will not work! Either

locate the unit differently, or take

advantage of the remote control

input on the rear of the player

(consult your dealer for further

information on this option).

DV79

E-10

English

DV79

E-11

P MODE

Press P MODE to toggle random playback

MODE

STATUS SRCH

ZOOM ANGLE SUBT PL

AUDIO TRIM TITLE RTN

MEM

SRCH (search)

It is possible to get access to any point on

the disc directly using the ‘Search’ menu.

Press SRCH to access the ‘Search’ menu.

RTN (return)

Press RTN to move back through the DVD

‘Disc’ and ‘Title’ menus. Note that this

feature is only of use with discs using

multi-level menus.

STATUS

Press STATUS once to show the elapsed and

remaining time of the disc. Press STATUS a second

time to give play status information about the

current disc. Press STATUS a third time to close

the status display.

The status information displayed varies depending

on the type of disc – DVD, CD or VCD.

MEM (memorise)

It is possible to ‘bookmark’ up to three points

on a DVD title, so you can jump quickly to

those parts of the title again (until the disc

is ejected or the player reset. Press MEM to

open the ‘Bookmark’ menu.

TITLE

Press TITLE to access the DVD’s ‘Title’ menu. Note

that this feature applies only to multi-title discs.

AUDIO

Some DVDs offer the facility to select

different audio tracks. Press AUDIO to cycle

through the available tracks.

The on-screen display shows the number,

language and type of audio track, e.g. ‘1 Eng

DD 6CH’.

SUBT (subtitle)

Press SUBT on the remote control to cycle through the

available subtitle languages, including ‘OFF’. Some discs

force subtitles on, over-riding player set up.

ANGLE

Some DVDs offer the facility to select different

camera angles. If this feature is available the

‘camera’ symbol lights in the display.

Press ANGLE to cycle through the available

angles.

ZOOM

Press ZOOM to enlarge a particular area

of the picture. Each press of the ZOOM

button increases the zoom, normally until

a maximum of 4x enlargement is reached.

Pressing ZOOM when the maximum

enlargement has been reached returns the

image to normal size.

While using the zoom function, the cursor

pad can be used to move around within

the image. The zoom function can also be

used when playback is paused.

Note that a zoom level of x1.25 is

particularly useful if the output from the

DVD player is in a screen format different

from that of your display device. A zoom

of x1.25 when a ‘widescreeen’ image is

displayed on a 4:3 display causes the bars

at the top and bottom of the screen to

disappear (although the sides of the image

are lost); a zoom of x1.25 when a 4:3

image is displayed on a widescreen display

causes the bars at the side of the image to

disappear (although the top and bottom of

the image are lost).

Advanced controls (CR-415)

PL (PRO LOGIC)

This button brings up a menu very

similar to the ‘Audio’ page of the Set-

up menu (as described on page 15)

and allows the Pro Logic II settings

to be changed while the disc is being

played.

TRIM

This button brings up a menu very similar to the ‘Trims’

page in the Set-up menu (as described on page 18). It

allows on-the- y changes to the relative volume of each

speaker in your system, while a disc is being played.

For a full description, see page 18.

DV79

E-12

English

DV79

E-13

Con guring your DVD player

Introduction

This section of the document describes the use of the ‘Set-up’ menu, which is used to con gure your

player for your system and your personal preferences.

Obtaining a picture

To view the Set-up menu for the initial con guration, we recommend the use of

the composite video output to connect to your display device. This is because the

high quality video output has several display modes and may be incompatible with

your display device in its default con guration.

Ensure that your display device is switched on and that you have selected the

correct video input. You should see the image shown on the right. This is the

image that the DVD player gives whenever there is no disc playing.

NOTE: To protect your screen from damage caused by persistent static

images, a ‘screen saver’ facility activates after a few minutes of inactivity.

When this occurs, the image shown on the right will be ‘bounced’ around the

screen. To reset the image to the central position, press the STOP button on

the player or on the remote control.

Using the Set-up menus

To enter the Set-up menu, ensure that no disc is playing. Press SETUP on the remote control: a menu

will appear on the screen.

The Set-up menu comprises seven pages of options. The top line of each page shows the page title,

indicating the nature of the settings controlled by the page. To make a change,  rst use the UP/DOWN

controls to highlight the item. Once the item to be changed has been highlighted, press RIGHT to open

the list of options for the menu item. The current option for the menu item is shown highlighted; the

UP/DOWN controls can be used to select the new option, then pressing LEFT con rms the selection and

closes the option list.

To change page, highlight the page bar at the top of the screen and use the LEFT/RIGHT controls

to move through the pages.

The UP/DOWN controls ‘wrap around’, so that with the highlight bar at the bottom of the screen,

pressing DOWN takes the bar to the top of the screen.

Items that are not applicable currently (for example, the Pro Logic II settings, when Pro Logic II

processing is switched off) are shown in dark blue, and cannot be highlighted or changed.

DV79

E-12

English

DV79

E-13

Operational set-up

OSD Language

This setting controls the language of the messages displayed on the On-Screen

Display (OSD). The default language is English, with three other languages

supported.

Note that this setting does not change the language of any information displayed

on the front panel, which is always in English.

OSD Status

This setting controls the ‘pop up’ messages that appear on screen.

On Pop-up messages are enabled

Off No pop-up messages, only menus when required.

Certain messages, such as ‘No Disc’ are always shown regardless of how this is set.

DVD menu

Some DVD discs support a number of different languages for the DVD disc menu (the menu present on

the DVD itself). This setting allows the preferred language to be speci ed. For example, if this item is set

to ‘French’ then disc menus will be displayed in French, where supported by the disc.

Note that not all discs will have your preferred language available.

Subtitle

This setting controls the subtitles displayed on the display device (although note that some discs may

force the subtitles to be displayed regardless of how this item is set).

Off No Subtitles

Auto Subtitles for the primary language on the disc

English English subtitles

French French subtitles, etc. (six languages are supported)

The default setting for Subtitle is ‘Off’; alternatively, choose the setting for the language you prefer. Note

that not all discs will have your preferred language available as a subtitle.

Force DVI

Even though your display device may be fully HDMI compliant, it is possible that in-line receivers or

repeaters may work only in DVI mode. In this case, it is useful to disable HDMI, forcing DVI output

instead.

Select YES to force the DV79 into DVI mode even when a HDMI device is detected; select NO otherwise.

If you are not using the HDMI capabilities of the DV79, then it does not matter which way this item is

set.

Remote type

This informs the player which type of remote control you are using, so that the player can take into

account the slight differences between the remote types. For ARCAM remote controls, the remote type is

always written on the front of the remote control, normally at the bottom of the unit.

CR-314 This selects the grey ARCAM CR-314 remote control

CR-415 This selects the black ARCAM CR-415 remote control

CR-80 This selects the black ARCAM CR-80 learning remote control

CR-9000 This selects the black ARCAM CR-9000 learning remote control

Other A non-ARCAM learning remote control is being used

It is important to choose ‘Other’ if the learning remote in use does not support RC-5 ‘toggle bits’.

Disc Priority

Some DVD discs show different material, or have different behaviour, depending on whether the disc is

played on a DVD-video or on a DVD-audio player. The ‘Disc Priority’ option allows you to con gure the

DV79 to be (primarily) one or other of the player types.

Note that, although this setting may be changed after a disc has been loaded into the DV79, this setting

does not take effect unless the disc is re-loaded (or a different disc is played).

English



 

 

 

 

 

 

 

DV79

E-14

English

DV79

E-15

Video set-up

If your display device is HDMI-compliant, the DV79 can read the capabilities of

the display device directly; the information allows the DV79 to con gure its output

automatically and optimally for the attached device. This is known as ‘plug and

play’.

The DV79 can be con gured for plug and play, or not; this depends on the ‘Output

Priority’ setting, described below. If the DV79 is con gured for plug and play, and

the display device cannot handle some of the options described below, then the

options shown will be restricted to just the ones applicable to the attached device.

For example, if the display device can handle PAL signals, but not NTSC, then NTSC

will not be shown as an option for the ‘TV System’ menu item.

See page 9 for more information about connecting to HDMI devices.

Output Priority

Allows speci cation of whether HDMI ‘plug and play’ capabilities should be used.

HDMI/DVI Select this item if you are connecting the DV79 to a HDMI-compliant device, and

you are happy for the DV79 to con gure itself automatically for the device it is

attached to.

This is the recommended setting if you are connecting the DV79 to a

HDMI-compliant device.

Analogue Select this setting if you are not connecting the DV79 to a HDMI-compliant

device.

TV System

This is set at the factory to be appropriate for the type of display device used in your country.

Should you need to change this setting, the options are explained below.

Auto The video output is taken from that recorded on the disc. When no disc is playing,

the logo screen is displayed using the standard of the last disc played.

NTSC NTSC is always used as the video standard. Note that PAL discs are converted to

NTSC, but this causes some reduction in the quality of the video output (and may

cause the video to become ‘jerky’). This is the best setting to use if your display

device can accept only NTSC video (this is generally the case in North America);

better results are obtained by using ‘Auto’, but your display device must be able

to support PAL.

PAL PAL is always used as the video standard. Note that NTSC discs are converted to

PAL, but this causes some reduction in the quality of the video output (and may

cause the video to become ‘jerky’). Better results will be obtained by using ‘Auto’,

but your display device must be able to support NTSC.

Progressive

Allows con guration of interlaced or de-interlaced (progressive scan) output.

Off The video output will always be interlaced (standard de nition video). Use this

setting if your display device does not support progressive scan.

NTSC only

(525)

The component video output will switch to progressive scan mode whenever the

output standard is NTSC (525). This would be whenever an NTSC disc is played,

or whenever ‘TV System’ is set to NTSC. The video output will revert to interlaced

(standard de nition) for PAL (625) modes. Use this setting only if your display

device supports NTSC progressive scan.

PAL only

(625)

The component video output will switch to progressive scan mode whenever the

output standard is PAL (625). This would be whenever a PAL disc is played, or

whenever ‘TV System’ is set to PAL. The video output will revert to interlaced

(standard de nition) for NTSC (525) modes. Use this setting only if your display

device supports PAL progressive scan.

On The component- and HDMI-video outputs will put progressive scan video out for

both PAL and NTSC discs. Use this setting only if your display device supports

progressive scan in both PAL and NTSC formats.

NOTE: When progressive scan is active, the component- and HDMI-video outputs will be in

Progressive mode; the other video outputs (Composite and S-Video) will be muted.

Since progressive scan must be Component, (not RGB), the ‘Analogue Video’ item will be

forced to ‘Component’ if progressive scan is enabled.

TV shape

This needs to be set correctly for the type of display device you have and the type of display you prefer.

4:3

Letterbox

Use this setting if you have a conventional 4:3 display device, and you prefer

to view wide screen movies in letterbox format (with black bars at the top and

bottom)

4:3

Panscan

Use this setting if you have a conventional 4:3 display device, and you prefer to

view wide screen movies in Pan & Scan format (cropping the sides of the image)

16:9 Use this setting if you have a wide screen (16:9) display device.

Material in 16:9 format is displayed so as to  ll the screen.

If you have a 4:3 display device and you have set a preference for PANSCAN, it does not mean you will

always see movies in this format, since Panscan display must be supported by the disc being played.



 

 

 

 

 

 

 

Not all displays support

progressive scan. If you

enable progressive scan

accidentally and your

display does not support

it, you may be unable

to view the picture from

the DVD player, including

the on-screen display

required to change the

video settings. To revert

to interlaced mode

without using the on

screen menus, press and

hold the STOP button on

the front panel at any

time. The video mode

will revert to interlaced

mode after the button has

been held in for about  ve

seconds.

If the picture is ‘jerky’

or ‘shimmers’, you may

be playing a disc that

has a format different

to the setting of your

player (a PAL disc played

with NTSC output, for

example). If your display

device can handle both

PAL and NTSC video, then

change the ‘TV system’

setting to ‘Auto’.

DV79

E-14

English

DV79

E-15

Analogue Video

This setting controls the type of video given out on the Component and SCART video outputs. It is set

at the factory to be appropriate for the type of display device used in your country, so it is best not

to change it. If it gets set incorrectly then the picture shown on the display device will have strange

colouring.

Component The video output on the Component video (3 phonos), SCART and HDMI

connections is Y, Pb, Pr component video.

RGB SCART The video output on the Component video (3 phonos), SCART and HDMI

connections is RGB. Note that if you are using RGB output via phono connectors,

you will also need to use COMPOSITE as a sync. signal.

Note that this setting has no effect on the video provided by the HDMI connector.

Digital Video

This setting controls the type of video given out over the HDMI connection.

YUV The HDMI connection carries Y, Pb, Pr (YUV) component video.

RGB SCART The HDMI connection carries RGB video.

Note that this setting has no effect on the analogue video outputs.

NTSC black (Pedestal)

This setting controls the ‘pedestal’ signal or black level when the NTSC video standard is used.

0 IRE This removes the pedestal from NTSC video. This setting should be used in Japan,

and also if you are using RGB video, whatever the country.

7.5 IRE This is the standard pedestal level that should be used in all countries that use

NTSC video, with the exception of Japan.

Note that this setting has no effect on PAL, progressive scan or HDMI outputs.

Audio set-up

This section allows you to con gure the type of analogue and digital audio outputs.

In particular, the digital output type needs to be set correctly if you are using an

external audio decoder, receiver or D-A converter.

Audio

Two different types of digital output are supported: ‘Bitstream’ and ‘Stereo PCM’.

Bitstream The Bitstream setting supports the following audio standards:

2 channel PCM (on CDs or DVDs)

Dolby Digital

MPEG multi channel

DTS multi channel

Use the Bitstream setting if you have an external decoder that

supports Dolby Digital.

Stereo PCM When the ‘Stereo PCM’ digital output is selected, all audio

material played is down-mixed to stereo and output as stereo

PCM. Use this setting if you have an external D-A converter that

supports only 2-channel PCM.

Since the digital and analogue outputs are closely related, the analogue audio output re ects the digital

output type selected.

The options available are as follows:

Bitstream +

6 Ch.

The digital output is ‘Bitstream’ (as described above). The analogue audio will

comprise up to six channels of output, depending on the source material, the

speaker con guration (see the ‘Speaker Setup’ section) and the ‘Pro Logic II’

setting (see below).

Bitstream +

2 Ch.

The digital output is ‘Bitstream’ (as described above). The analogue audio will

comprise a 2-channel stereo down-mix of the source material.

PCM + 2 Ch. The digital output is ‘Stereo PCM’ (as described above). The analogue audio will

comprise a 2-channel stereo down-mix of the source material.

Language

This controls the default audio track, when there is more than one audio track present.

The default setting is ‘English’. Choose the setting you would like as default. Note that the audio-

language preference setting is not respected by all discs, which may impose their own default choice.

Down-sample

This needs to be set correctly if you are using an external audio decoder, receiver or D-A converter.

Max 96K Choose this option if your external audio decoder is able to process digital audio

with a sample rate of up to 96kHz, or if you are not using the digital audio

outputs. This is the maximum sample rate present on DVD-video discs.

Max 48K Choose this option if your external audio decoder is unable to process digital

audio with a sample rate of up to 96kHz, or the HDMI connection is being

used to carry the audio.

Note that this setting is relevant only to the output from DVD-video discs. DVD-audio disc digital output

os limited to 2-channel PCM, at a maximum sample rate of 48kHz.



 

 

 

 

 

 

 

 

DV79

E-16

English

DV79

E-17

Compression

Allows compression of the audio stream to be turned on or off, where ‘On’ is intended for ‘late night’

listening when large volume changes are not desirable.

Turning compression on increases the volume of the quiet passages and decreases the volume of the

louder passages, i.e., the total dynamic range of the audio is reduced. Compression can be disabled by

setting this item to ‘Off’.

Compression is available only on Dolby Digital recordings.

Pro Logic II

Dolby Pro Logic II decoding is designed to produce a 5-channel output from two-channel source material.

This item can be changed only if the ‘Audio’ menu item (described above) is set to ‘Bitstream/6 Ch’.

Set this item to one of the following. Due to the different recording methods used for movies and music, it

is recommended that the correct decoding mode for your source material is used to obtain the best results.

Off No Pro Logic decoding is performed.

Dolby Pro Logic decoding is performed. Dolby Pro Logic decoding is a legacy mode,

and we recommend using one of the Pro Logic II decoding options, instead.

Movie Movie mode should be used with material marked as ‘Dolby Surround’ encoded.

Music Music mode is for use with any stereo music recording. As the optimum decoding

method varies according to the recording, Music mode allows user adjustment of

the processing characteristics; information about adjusting the Music mode by

using ‘Dimension’, ‘Centre Width’ and ‘Panorama’ controls can be found below.

Matrix The Matrix mode is the same as the Music mode except that the directional

enhancement logic is turned off. Matrix mode may be used to enhance mono

signal by making them seem ‘larger’.

Dimension

(This setting can be adjusted only when Dolby Pro Logic II Music mode is selected.)

‘Dimension’ allows the user gradually to adjust the sound eld either towards the front or towards the

rear. If a recording is too spacious or strong from the surrounds, it can be adjusted ‘forward’ to get a

better balance. Likewise, if a stereo recording is somewhat too ‘narrow’ sounding, it can be adjusted

toward the rear to get a more enveloping, immersive result. We recommend ‘Dimension’ is set to 0 for

normal use.

Centre Width

(This setting can be adjusted only when Dolby Pro Logic II Music

mode is selected.)

With Pro Logic II decoding, dominant centre signals come only from

the centre speaker. If no centre speaker is present, the decoder splits

the centre signal equally to the left and right speakers to create a

‘phantom’ centre image. The Centre Width control allows variable

adjustment of the centre image so it may be heard only from the

centre speaker; only from the left/right speakers as a phantom

image; or from all three front speakers to varying degrees. We

recommend ‘Centre Width’ is set to 3 for normal use.

Panorama Mode

(This setting can be adjusted only when Dolby Pro Logic II Music

mode is selected.)

Extends the front centre image to include the surround speakers for

an exciting ‘wrap-around’ effect with side wall imaging.

Speaker set-up

This menu screen allows you to specify the speaker con guration that is connected

to the analogue ouputs of your DVD player. (Note that these settings do not

affect the digital output in any way.) It is important that this con guration

re ects accurately the actual situation, otherwise audio quality may be severely

compromised.

The speakers are indicated as follows:

Front L/R This is the setting for the ‘Front’ speakers (the speakers used

for 2-channel stereo output).

Centre This is the ‘Centre’ speaker setting.

Surround

L/R

This is the setting for the ‘Surround’ speakers (normally next-

to or behind the user).

Subwoofer This is used to indicate whether a subwoofer is connected.

For each speaker, the player can be con gured to send either audio with the full frequency range

of the source material, or with a reduced frequency range. The reduced frequency range option is

used normally when ‘satellite’ speakers are used for the surround channels; these cannot handle low

frequency information. Full frequency speakers are commonly called ‘Large’ speakers, with reduced-

range speakers given the name ‘Small’. Low frequency information is re-routed from ‘small’ speakers to

‘large’ speakers, or to the subwoofer (depending on the speaker con guration).

NOTES:

1. Any speaker that is not connected should be identi ed by selecting ‘Not Present’ for that speaker.

2. Although the DV79 is very  exible in the speaker con gurations it can handle, some restrictions

have been applied. For example, if no subwoofer is present, then it is not possible to con gure

the Front speakers to be ‘Small’ since there would be nowhere to redirect the low frequency

information.

(This setting can be adjusted only when Dolby Pro Logic II Music

mode is selected.)

With Pro Logic II decoding, dominant centre signals come only from

the centre speaker. If no centre speaker is present, the decoder splits

the centre signal equally to the left and right speakers to create a

‘phantom’ centre image. The Centre Width control allows variable

adjustment of the centre image so it may be heard only from the

centre speaker; only from the left/right speakers as a phantom

image; or from all three front speakers to varying degrees. We

recommend ‘Centre Width’ is set to 3 for normal use.

Panorama Mode

(This setting can be adjusted only when Dolby Pro Logic II Music

mode is selected.)

Extends the front centre image to include the surround speakers for

an exciting ‘wrap-around’ effect with side wall imaging.











Display Centre spreading

effect

0 No centre spreading

1 20.8°

2 28°

3 36°

4 54°

5 62°

6 69.8°

7 Phantom centre

The ‘Centre Width’ setting

for Dolby Pro Logic II

Music Mode



 

 

 

 

 

 

DV79

E-16

English

DV79

E-17

Stereo+Sub

This setting is relevant to 2-channel source material only (such as CDs). It controls whether the

low frequency information is redirected to the subwoofer, or not. This item can be changed only if

a subwoofer is speci ed as present in the system.

None No redirection of low-frequency information occurs; all the audio is sent to the

Front speakers.

Crossover Low-frequency information is redirected to the subwoofer, with the remaining

(higher-frequency) information sent to the Front speakers.

Duplicate All the audio is sent to the Front speakers. In addition, the low-frequency

information is duplicated to the subwoofer.

Crossover Frequency

This setting de nes the frequency at which bass redirection begins. Frequencies below this level

are redirected from ‘small’ speakers to the Fronts or to the subwoofer; frequencies above this

level are not redirected. The redirection frequency is the same for all the speakers in a system.

The optimum crossover frequency depends on the characteristics of your speaker set-up, and is

best determined by experimentation. We suggest you start at 100Hz.

Delay set-up

The delay set-up menu page allows two different type of delay to be con gured:

those due to speaker positioning and those due to video post-processing.

Speaker positioning

The relative positioning of speakers within a room (particularly a large room)

may mean that sound from some speakers arrives at the listener later than

sound from others. By altering the delay settings for the different speakers,

this difference in arrival time can be reduced or eliminated.

When setting the delay, it should be imagined that the listener is sitting in a

circle of the speakers; the delay indicates the distance of the speaker from the

listener.

Measurement Units

Your DV79 allows you to choose the measurement units that you feel most

comfortable with: metres or feet.

Delays

Delays for the front, centre and surround speakers can be set using the associated sliders. A delay

may be necessary for a speaker set if those speakers are further away from the listener than the

others – specifying the different speaker distances will cause a slight delay to be added to the output

of the closest speakers so that the sound from all the speakers will arrive at the listener at the same

time.

Video post-processing (lip-sync.)

Delay (NTSC/PAL)

Modern displays and video scalers often employ digital video processing that can introduce a

signi cant video delay. The ‘Delay’ menu items allow correction of this effect by delaying the audio

soundtrack up to 150 milli seconds. The amount of correction required in a given system is best

determined by experimentation.

�

If the interlaced video outputs of the DV79 are in use and the display is converting the signal to

progressive scan then we recommend a delay of 50–80ms, depending upon the display.

�

If the progressive video output of the DV79 is in use, the player corrects automatically for its own

processing delays and it is unlikely that additional delay will be necessary. Therefore, start by

setting these items to 0ms (no delay).

Trim set-up

The relative sensitivity (volume) of different speakers can lead to some speakers

sounding disproportionately loud or quiet, relative to others in the system. The

trims setting of your DV79 can help to address this inbalance.

Test Noise

Setting this item to ‘On’ causes pink noise to be generated from the speaker

indicated by the on-screen highlight. The noise is at the volume indicated by

the slider for the speaker. Setting this to ‘On’ may be useful in ensuring that the

relative volume for each speaker is the same.

Note that this setting is set automatically to ‘Off’ on exit from this menu page.

Trims

Trims for all the speakers can be set using the associated sliders. These settings

are useful if the speakers have different sensitivities (and so have different volumes

for the same input levels). The trims can be set in 1dB steps.

Subwoofer/Stereo+Sub trims

Both the ‘Subwoofer’ and the ‘Stereo+Sub’ trims control the subwoofer trim setting. ‘Subwoofer’ is the

trim used when multi-channel material is being played; ‘Stereo+Sub’ is the subwoofer trim used with

2-channel material.





 

 

 



 

 

No sound from the

centre/rear speakers?

Ensure that the following

are correct:

A multi-channel source

is being played;

The ‘Audio’ item is set

to ‘Bitstream/6 Ch.’;

The connection

between the DV79 and

your audio device is made

correctly – if using multi-

channel analogue output,

check that the cables

have not been swapped.



 

 

 

 

 

 

 

 

DV79

E-18

English

DV79

E-19

Access set-up

Password

The password setting works in conjunction with the rating setting (the next

menu item) to provide a means of limiting content playback by children (parental

control).

You will see there are four dashes and a padlock symbol. Normally the padlock

symbol will be open and this means the parental control is unlocked. Under this

condition the rating setting may be freely changed.

To lock the parental control, choose a suitable four digit number. Don’t forget your

password as you will need to know it to unlock the player. Highlight ‘Password’ and

enter your four digit number using the numerical keys on the handset. When all

four digits have been entered, press OK on the handset. The player is now locked

and you will not be able to change the rating setting.

To unlock the parental control, highlight ‘Password’ and enter your four digit

number, followed by OK.

Note that a different pass-code can be selected each time that the player is locked.

Rating

The rating setting is used in conjunction with the password to restrict the content of DVD titles that may

be played. To change this setting the parental control must be unlocked.

The term ‘Parental level’ refers to a standard de ned for DVDs. DVD movies may have a parental level

between 1 and 8. Note that this only applies to DVD video discs that have the parental level correctly

implemented. Some DVD video titles do not respond to parental control settings, and Video CDs have no

mechanism for parental control.

Once the rating level has been set, DVD titles with parental level higher than the setting will not play.

Sometimes DVD video titles may be produced that have the parental level set for speci c scenes, so a

disc will play but skip or substitute certain scenes.

Completing the set-up

Complete the set-up procedure by pressing SETUP on the remote control. This saves all the data and

closes the set-up menu. You can press SETUP at any time while in a menu to quit from it.

To return to the set-up menu at any time, ensure that there is no disc playing and press the SETUP

button.



 

 

DV79

E-18

English

DV79

E-19

Advanced DVD and VCD features

This section explains the more sophisticated DVD and VCD features, such as special playback modes.

The operations described here are not exactly the same for DVDs and VCDs, but are similar enough to

make it appropriate to group them together.

Note that many VCDs have a single track, so some operations involving tracks will not be relevant.

Jumping to a particular point

Press the SRCH button on the remote control to open the ‘Search’ menu:

If the disc is playing, then the elapsed and total times on the disc are shown in the

top right of the page.

A jump can be performed using different speci ers: jump to a particular time or to

a speci ed chapter/track on the disc.

Time

Highlight the ‘Time’  eld and enter the time in hours, minutes and seconds, then

press OK. The Search menu is removed from the screen and playback starts from

the time speci ed. Invalid time entries are ignored.

Title/Chapter

(Applies to DVDs only) To jump to a title or chapter, highlight the title/chapter

position and enter the number of the title/chapter to jump to, before pressing OK.

It is possible to jump to a chapter within a different title to the current one by entering a value into both

 elds. Note that specifying a title without a chapter will jump to the  rst chapter in the title.

Group/Track

(Applicable to DVD-audio discs only.) To jump to a group or track, highlight the group/track position and

enter the number of the group/track to jump to, before pressing OK. It is possible to jump to a track

within a different group to the current one by entering a value into both  elds. Note that specifying a

group without a track will jump to the  rst track in the group.

Track

(Applies to VCDs only) To jump to a speci ed track on a VCD, enter the track number in the ‘Track’  eld,

then press OK. Note that many VCDs have only one track.

Closing the Search menu

When displayed, this menu screen can be closed again by pressing the SRCH button (which also has the

effect of cancelling the search).

Special playback modes

Playback modes are available that allow repeat, shuf e and programmed playback.

Repeat

Press the RPT button on the remote control to cycle through the repeat options. For DVDs, a chapter or

title repeat may be selected (i.e., play continuously the current chapter or the current title). For VCDs, a

track or disc repeat is available.

When a chapter/track repeat is selected, the loop symbol on the front panel display is illuminated and

the current chapter/track is repeated. If a title/disc repeat is selected, the loop symbol and ‘ALL’ are

illuminated and the current title/disc is repeated.

To cancel repeat, press the RPT button until ‘Repeat: Off’ is displayed.

Shuf e

Press the P MODE button on the remote control to switch shuf e play on.

The ‘RAND’ (random play) indicator shows on the display, and the chapters/tracks are played in random

order.

To cancel random play, press the P MODE button for a second time.

A-B repeat

The DV79 can repeat a speci c section of a DVD or VCD; this is called an A-B repeat.

To perform an A-B repeat, wait until the disc is at the point where you want the repeat to start, then

press A-B. The OSD shows a repeat symbol, followed by ‘A–’, and the front panel shows ‘A–’.

Press A-B again at the point you want the repeat to end. The repeat symbol, followed by ‘A-B’ is shown

on the display device, and the front panel shows ‘A-B’. The selected section is repeated in a loop.

To cancel the A-B repeat, press A-B again. An ‘Off’ message is displayed on the OSD.

English

 





 

  

DV79

E-20

English

DV79

E-21

Programmed playback (DVD-video)

Press PROG on the remote control to open the ‘Programme’ menu. Note that

playback must be stopped  rst.

The bottom of the screen shows the number of titles present on the disc, together

with the number of chapters in the title selected currently (or the  rst title if no

title has yet been speci ed). Below this is an information line, giving relevant

information for the cursor position.

You can enter a sequence of up to 20 title/chapter combinations for programmed

playback. If you enter data that is invalid for the current disc, the  eld is erased

automatically.

A number of aids have been built in to the programme menu to make it easier to

use. These are best illustrated by an example. Let’s assume that you want to play

chapters 5, 7, 9, 4, 8, 3, and 1 (in that order) of title 1, then all of title 2.

First, highlight the title position for the  rst programmed item, then press the

number 1 on the remote control: ‘1’ is shown in the position. Using the remote

control, press

to highlight the chapter position. The message at the bottom of

the screen changes accordingly, prompting you for the required information. Press

5 on the remote handset.

Since we have a number of chapters all from the same title, it would be a lot of

work to have to enter the title number each time. Press

on the remote handset.

Notice that the player assumes that the title number remains the same for this

entry as for the previous one. Enter the remaining chapter numbers, pressing

after each one. (Note that pressing

at the bottom of a column places the cursor

at the top of the next column.)

Next, we want to specify all of title 2. For this, highlight the title position of the next

entry (entry 8) and enter the number 2, indicating title 2. Highlight the chapter

position and, without entering any number, press

. The player  lls in the text ‘All’

to indicate that all the chapters in title 2 will be played.

Program (DVD-audio)

The programming of a sequence for a DVD-audio disc is essentially the same as for a DVD-video disc,

and the instructions given above should be followed. For DVD-audio discs, the ‘titles with chapters’

combination found on DVD-video discs changes to ‘groups with tracks’.

Programmed playback (VCD)

The bottom of the screen shows the number of tracks present on the disc. Below this is an information

line, giving relevant information for the cursor position.

You can enter a sequence of up to 20 tracks for programmed playback. If you enter data that is invalid

for the current disc, the  eld is erased automatically.

To program the player, highlight the  rst entry (using the cursor pad on the remote control), then press

the number of the track you want to play  rst. To enter a second track, move down, then type the

number of the second track to play, etc. To enter a track number greater than 9, press the two digits

sequentially (e.g., for track 10,  rst press 1, then press 0).

General

To play the programme you have entered, highlight the ‘Play’ button on the screen and press OK. The

‘PROG’ indicator shows in the display and the programmed sequence begins.

If you make a mistake while programming, you can clear a single  eld by highlighting it and pressing

CLEAR. To clear all the  elds at once, highlight the ‘Clear All’ button on the screen and press OK.

To stop the programmed sequence and return to normal playback, select the PLAY button in the

programme menu with no programme speci ed. This clears the programme mode and cause normal

playback order to be resumed.

Note that skipping forward or back through tracks while in programmed play mode skips through the

programmed sequence.





 

















































 











































Page is loading ...

Arcam DVD Player DV79 User manual

Brand: Arcam

Model: DVD Player DV79

Category: DVD players

Type: User manual

This manual is also suitable for

DV79

Download PDF

report

in other languages

Nederlands: Arcam DVD Player DV79 Handleiding

Arcam DVD Player DV79 User manual

This manual is also suitable for

Arcam DVD Player DV79 User manual

in other languages

Related papers

Other documents