Rival 16173 is a lightweight iron designed for both dry and steam ironing. It features a transparent water tank that allows you to easily monitor the water level, and a spray mist function to dampen fabrics and remove wrinkles. The iron has a range of temperature settings, making it suitable for a variety of fabrics, from delicate silks to sturdy linens.
Here are some of the key features and benefits of the Rival 16173:
- Lightweight and easy to handle
- Transparent water tank for easy monitoring
- Spray mist function for dampening fabrics and removing wrinkles
- Range of temperature settings for different fabrics
Rival 16173 is a lightweight iron designed for both dry and steam ironing. It features a transparent water tank that allows you to easily monitor the water level, and a spray mist function to dampen fabrics and remove wrinkles. The iron has a range of temperature settings, making it suitable for a variety of fabrics, from delicate silks to sturdy linens.
Here are some of the key features and benefits of the Rival 16173:
- Lightweight and easy to handle
- Transparent water tank for easy monitoring
- Spray mist function for dampening fabrics and removing wrinkles
- Range of temperature settings for different fabrics
Customer Assistance:
Atencion al cliente
1-866-321-9509
16173
™
lightweight
iron
plancha
ligera
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 1
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always
be followed including the following:
1. READ ALL INSTRUCTIONS BEFORE USING APPLIANCE.
2. Close supervision is necessary when appliance is used near children.
Keep the Iron out of the reach of children and pets.
3. This appliance is not for use by children.
4. Do not operate any appliance if the cord is damaged. Do not use this appliance
if the unit malfunctions, if it is dropped or has been damaged in any manner.
In order to avoid the risk of an electric shock, never try to repair the Iron
yourself. Bring it to a qualified technician for examination, repair or electrical
or mechanical adjustment. An incorrect reassembly could present a risk
of electric shock when the Iron is used
5. To protect against a risk of electric shock, do not immerse the Iron in water
or other liquid. See Care & Cleaning Instructions.
6. Do not use outdoors or while standing in a damp area.
7. Use Iron only for its intended use.
8. Always turn the temperature control/fabric selector dial to MIN before plugging
it into or unplugging it from the electrical outlet. To disconnect, pull directly
on the plug; do not pull on the power cord.
9. Do not allow cord to touch hot surfaces.
10. Allow Iron to cool completely before storing.
11. Always unplug Iron from electrical outlet when filling with water or emptying,
when not in use and before cleaning.
12. Do not leave Iron unattended while hot or connected or on an ironing board.
13. Position Iron carefully on ironing board to avoid it from being knocked over.
14. Do not touch hot metal parts, hot water, or steam released from the Iron,
as contact may cause burns. Use caution when turning a steam iron upside
down, as there may be hot water in the water tank.
15. Do not plug/unplug the product into/from an electrical outlet with a wet hand.
16. CAUTION! To reduce the risk of personal injury, this product is intended
solely for non-commercial, non-industrial, household use in the dry or steam
pressing of garments and fabrics. Do not use the product outdoors or for any
other purpose than intended.
SPECIAL INSTRUCTIONS
1. This is a high wattage appliance. To avoid a circuit overload, do not operate
another high wattage appliance on the same circuit.
2. Care should be taken to arrange the cord so that it cannot be pulled or tripped
over.
2
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 2
ADDITIONAL IMPORTANT SAFETY
INSTRUCTIONS
CAUTION HOT SURFACES: This appliance generates heat and escaping steam
during use. Proper precautions must be taken to prevent the risk of burns,
fires or other injury to persons or damage to property.
1. All users of this appliance must read and understand this Instruction Manual
before operating or cleaning this appliance.
2. The cord to this Iron should be plugged into a 120V AC electrical outlet only.
3. If this appliance begins to malfunction during use, immediately unplug the cord.
Do not use or attempt to repair the malfunctioning appliance.
4. Do not leave Iron unattended during use.
NOTES ON THE PLUG
This appliance has a polarized plug (one blade is wider than the other). To reduce
the risk of electric shock, this plug will fit in a polarized outlet only one way.
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not modify the plug in any way.
NOTES ON THE CORD
If an extension cord is absolutely necessary, a 3 x 16 AWG cord should be used.
Cords rated for less amperage may overheat.
ELECTRIC POWER
If the electrical circuit is overloaded with other appliances, your appliance may not
operate properly. It should be operated on a separate electrical circuit from other
appliances.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
3
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 3
GETTING TO KNOW YOUR LIGHTWEIGHT IRON
PRODUCT MAY VARY SLIGHTLY FROM ILLUSTRATIONS.
BEFORE USING FOR THE FIRST TIME
1. Remove any adhesive stickers that may be attached to the soleplate.
Any residual adhesives can be removed by rubbing gently with a soft,
water-dampened cloth.
2. New irons commonly release some light smoke or vapors when used for
the first few times. This light smoke is due to the initial heating of the materials
used in the manufacturing of the product. The release of this light smoke
is normal and does not indicate a fault in the product.
3. Residual moisture may also be present in the water tank. This is normal.
OPERATING INSTRUCTIONS
1. Always check garment labels for garment symbols suggesting that a fabric
should or should not be ironed. Always follow the temperature and steam
settings recommended by the fabric manufacturer.
2. Turn the steam control dial to the desired position. See Dry Pressing and Steam
Pressing sections following for detailed operating instructions.
3. Turn the temperature control/fabric selector dial to the desired
temperature/fabric setting: high temperature for cotton-linen, medium
temperature for wool, and low temperature for rayon, silk and acrylics.
(See Figure 3a.)
4. To prevent damage to garments from the use of too hot an Iron, it is best
to first iron garments that require low temperature. If you should need to adjust
from a high setting to a lower temperature, for example 3 (•••) to 1 (•),
allow the Iron about 5 minutes to reach the lower temperature.
M
A
X
Figure 1
Spray Mist Button
P
ower Cord
W
ater Tank Inlet
Steam Control Dial
Transparent
W
ater Tank
Spray Nozzle
Heel
T
emperature Control/
Fabric Selector Dial
P
ower READY Light
P
olished Soleplate
with Steam Vents
4
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 4
5
5. If you are unsure of a garment’s fabric content, start on a low setting and test
the Iron on an area of the garment that does not show, such as a seam.
Gradually increase the heat setting until wrinkles remove without damaging
the fabric.
6. To prevent shine, iron dark garments or those made of silk, acetate or rayon,
inside out.
IMPORTANT! To protect the soleplate from scratching, avoid ironing over
snaps, zippers, metal buttons, etc. Cover these objects with a pressing cloth
(not included) before ironing.
FILLING THE WATER TANK
WARNING: Make sure the Iron is completely cool and unplugged before adding
water to the water tank.
1. Before adding water to the tank, always check the garment label of the item
to be ironed for care instructions. Some fabrics may be damaged when exposed
to steam or water, and should be pressed dry, with an empty tank.
2. Turn the steam control dial to NO STEAM. (See Figure 2.)
3. Turn the temperature control/fabric selector dial to MIN. (See Figure 3a.)
4. Use a spouted cup to pour water into the water tank inlet until the water level
reaches the MAX water level mark on the transparent water tank.
(See Figure 4.)
IMPORTANT! Use tap water only. Distilled water may cause the iron to spit
or leak.
Exception: If tap water is very hard, use a mixture of
1
⁄2 tap water
and
1
⁄2 distilled water.
CAUTION: Do not fill the water tank above the MAX water level mark.
M
A
X
R
A
Y
O
N
S
I
L
K
A
C
R
Y
L
I
C
L
I
N
E
N
C
O
T
T
O
N
W
O
O
L
M
A
X
M
I
N
Maximum Water
Level Mark
Figure 2
Figure 3a
Figure 4
R
A
Y
O
N
L
I
N
E
N
C
O
T
T
O
N
W
O
O
L
M
A
X
Range for steam
Figure 3b
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 5
DRY PRESSING
1. The Iron can be used on the NO STEAM (dry) setting with or without water
in the tank, however, it is best to avoid having the tank too full of water while
dry ironing.
2. Turn the steam control dial to NO STEAM. (See Figure 5.)
3. Turn the temperature control/fabric selector dial to MIN. (See Figure 3a.)
4. Stand the Iron on its heel in an upright position on a flat, level, stable,
heat-resistant surface.
5. Plug the power-supply cord into a 120V AC electrical outlet.
6. Turn the temperature control/fabric selector dial to the desired setting.
(See Figure 3a.) The power READY light will turn off when the Iron has reached
the desired temperature.
NOTE: During use, the power READY light will cycle on and off as the Iron
maintains the proper temperature.
CAUTION HOT SURFACES: Avoid coming in contact with escaping steam.
CAUTION: Never leave the Iron unattended.
7. When ironing is finished, turn the temperature control/fabric selector dial
to MIN. (See Figure 3a.)
8. Unplug the Iron from the electrical outlet.
STEAM PRESSING
1. Stand the Iron on its heel in an upright position on a flat, level, stable,
heat-resistant surface.
2. Turn the temperature control/fabric selector dial to MIN. (See Figure 3a.)
3. Plug the power-supply cord into a 120V AC electrical outlet.
4. Turn the temperature control/fabric selector dial to the desired setting within
the black steam range (See Figure 3b.). The power READY light will illuminate.
5. The power READY light will turn off when the Iron has reached the desired
temperature.
NOTE: During use, the power READY light will cycle on and off as the Iron
maintains the proper temperature.
CAUTION HOT SURFACES: Avoid coming in contact with escaping steam.
CAUTION: Never leave the Iron unattended.
6. Turn the steam control dial to STEAM. (See Figure 6.)
7. When ironing is finished, turn the steam control dial to NO STEAM then turn
the temperature control/fabric selector dial to MIN. (See Figure 3a.)
8. Unplug the Iron from the electrical outlet.
IMPORTANT: The water tank should be emptied after each use.
Figure 5
Figure 6
6
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 6
SPRAY MIST
U
se the Spray Mist to dampen dry, difficult fabrics, to remove wrinkles and to set
c
reases. The spray mist can be used while either dry or steam pressing.
1. Make sure there is adequate water in the water tank. See Filling the Water Tank
section for specific operating instructions.
CAUTION: IF THE IRON IS HOT, DO NOT ADD WATER.
2. Firmly press the spray mist button. (See Figure 7.) It may be necessary to press
the button 2 to 3 times successively to release the initial spray of water.
NOTE: Spray misting can be used on any heat setting and does not affect
the ironing temperature.
CAUTION HOT SURFACES: Avoid coming in contact with escaping steam.
USER MAINTENANCE INSTRUCTIONS
This appliance requires little maintenance. It contains no user serviceable parts.
Do not try to repair it yourself. Contact a qualified appliance repair technician
if the product requires servicing.
EMPTYING THE WATER TANK
IMPORTANT: The water tank should be emptied after each use.
1. Unplug the power-supply cord from the electrical outlet.
2. Empty the water tank by turning the soleplate away from you; then carefully
turn the Iron upside down over a sink. Allow any remaining moisture inside
the Iron to evaporate before storing.
CAUTION: Even if the soleplate is cool, use caution when draining water
from the water tank as the water may still be hot.
CARE & CLEANING INSTRUCTIONS
CAUTION: Unplug the power-supply cord from the electrical outlet before cleaning
the exterior of the Iron and storing. Never immerse the cord, plug or Iron in water
or any other liquid.
1. To remove or clean starch or other materials from the ironing surface
of the soleplate, apply a small amount of mild, non-abrasive cleaner
to a water-dampened cloth to form a paste on the cloth.
2. Gently rub paste onto the cooled soleplate and wipe it clean with a moist cloth.
WARNING: Never use scouring pads, abrasive, or harsh cleaners as these
will scratch the soleplate.
WARNING: Never add any chemical cleaning agents or solvents to the water
tank.
STORING INSTRUCTIONS
IMPORTANT! Allow the Iron to COOL COMPLETELY before storing.
1. Empty the water tank after each use.
2. Wrap cord loosely around the cooled Iron when storing.
3. To protect the soleplate, place the Iron in an upright position on its heel.
Figure 7
7
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 7
ONE YEAR LIMITED WARRANTY
This product carries a warranty that it will be free from defects in material
and workmanship for a period of one year from the date of purchase. This warranty
is valid for the original retail purchaser from the date of initial retail purchase
and is not transferable. Keep your original sales receipt.
IMPORTANT: This warranty does not cover damages resulting from accident,
misuse or abuse, lack of reasonable care, the affixing of any attachments not
provided
with the product, loss of parts, or subjecting the appliance to any but the specified
voltage. (Read directions carefully.)
If service is required during the warranty period, properly pack your unit.
We recommend using the original carton and packing materials. Return the product
to your nearest Wal*Mart store with the sales receipt. A replacement or refund
may be offered at the discretion of Wal*Mart. If additional assistance is needed,
please contact customer assistance at: 1-866-321-9509.
Wal*Mart expressly disclaims all responsibility for consequential damages
or incidental losses caused by use of the appliance. Some states do not allow
this exclusion or limitation of incidental or consequential losses so the foregoing
disclaimer may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which may vary from state to state.
SAVE THIS FOR YOUR RECORDS
RIVAL
™
logo is a trademark of Sunbeam Products, Inc. used under license
by Wal-Mart Stores, Inc., Bentonville, AR 72716.
Made in China.
8
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 8
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
SO-309001_16173 Rival Iron WM USA IM_Layout 1 12-04-11 11:37 AM Page 16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Rival 16173 is a lightweight iron designed for both dry and steam ironing. It features a transparent water tank that allows you to easily monitor the water level, and a spray mist function to dampen fabrics and remove wrinkles. The iron has a range of temperature settings, making it suitable for a variety of fabrics, from delicate silks to sturdy linens.
Here are some of the key features and benefits of the Rival 16173:
- Lightweight and easy to handle
- Transparent water tank for easy monitoring
- Spray mist function for dampening fabrics and removing wrinkles
- Range of temperature settings for different fabrics
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
Other documents
-
GE 681131689434 User manual
-
BLACK DECKER PRO IR2250 User guide
-
Black & Decker D5501 User manual
-
Continental CP43021 User manual
-
Black and Decker D5500 User guide
-
Sunbeam 3040 User manual
-
-
Hover-1 HOVER-1 RIVAL Rocket Hoverboard User manual
-
Maytag M400 User manual
-
StoreBound M400 User manual
