Symmons SLW-6612-1.0 Installation guide

Unity

™



-0.5 0.5 gpm (1.9 L/min) aerator



-1.0 1.0 gpm (3.8 L/min) aerator



-Delete

Sufﬁx

1.5

2.2 gpm (8.3 L/min) aerator



-STN Satin Nickel ﬁnish

Model Numbers

Two Handle Widespread Lavatory Faucet

Operation & Maintenance Manual

SLW-6612-1.5, SLW-6610-1.5

Two handle widespread lavatory faucet featuring an 8” to

16” mounting conguration. Includes ceramic cartridges,

1/4” copper supply lines, 1/2” IPS inlet connections, 50/50

drain assembly and standard 1.5 gpm (5.7 L/min) aerator.

Components made from brass and nonmetallic materials

plated in standard polished chrome nish.

Speciﬁcation

Warranty

Limited Lifetime - to the original end purchaser in

consumer/residential installations.

5 Years - for industrial/commercial installations.

Refer to www.symmons.com/warranty for complete

warranty information.

Dimensions

Note: Dimensions subject to change without notice.

Modiﬁcations

Note: Append appropriate -sufx to model number.



SLW-6612-1.5

Unity Two Handle Widespread Lavatory Faucet



SLW-6610-1.5

Unity Two Handle Widespread Lavatory Faucet

Less Rod & 50/50 Drain Assembly

Measurements

A 8”, 203 mm

B 5”, 127 mm

C 3 3/16”, 81 mm

D

Deck Thickness Ref.

Max. 1 3/8”, 35 mm

E

Hole Size

Min. Ø 1 3/8”, 35 mm

Max. Ø 1 5/8”, 41 mm

F

(2x) Hole Size

Min. Ø 1 1/4”, 32 mm

Max. Ø 1 1/2”, 38 mm

G 3 15/16”, 100 mm

H 5 1/16”, 129 mm

I Min. 2”, 51 mm

J 1/2-14 NPSM

AA

C

BB

D

EE

FF

G

H

I

J

Compliance

Certied by

CSA Group

-NSF/ANSI 372, NSF/ANSI 61.9

-ASME A112.18.1/CSA B125.1

-WaterSense 1.5 gpm (5.7 L/min)

For California Residents

WARNING: This product contains chemicals known to

the State of California to cause cancer, birth defects, or

other reproductive harm.

2

*Note: Append -STN to part number for Satin Nickel

nish.

A

B

C

H

I

J

K

L

N

P

Q

R

O

D

G

F

T

S1

S4

S5

S12

S3

S6

S9

S10

S11

S13

S14

S2

S7

S8

M

S

E

U

Replacement Parts

Item Description Part Number

A Lift Rod RL-210*

B

C

D

(2x) Handle Kit RL-209*

H Hot Cartridge RL-075

I Cold Cartridge RL-076

J

K

Aerator & Key

LN-333-KIT (2.2)

FLR-102-1.5-KIT (1.5)

LN-742-KIT (1.0)

FLR-102-0.5 (0.5)

L

N

O

Mounting Hardware

(Spout)

RL-123

P

Q

R

Mounting Hardware

(Valve Bodies)

RL-211

S 50/50 Drain Assembly

RL-223*

(SLW-6612-1.5)

U Grid Drain

P-26*

(SLW-6610-1.5)

Tools Required

Adjustable wrench

Allen wrench (1/16”)

Plumber putty

Plumber tape

PLUMBER

PUTTY

Parts Breakdown

3

P

Q

P

Q

R

M

2) Insert valve bodies (M) through

sink holes.

M

3) Install washer (P), nut (Q) and

screws (R) to valve body (M) to

secure assembly under deck

surface.

M

P

Q

R

M

P

Q

R

If replacing an older faucet

ensure water supply is turned

OFF before removing, then

turn faucet control valve ON to

relieve water pressure.

1) Remove washer (P), nut (Q) and

screws (R) from valve body (M).

5) Install gasket (L), washer (N) and

nut (O) to spout (F) to secure

assembly under deck surface.

1

2

L

N

F

O

6) Seat ange (S4) into sink (S5 gas-

ket optional). Install gasket (S6),

washer (S9) and nut (S10) onto

ange (S4) from below sink, but

do not secure nut. Screw on tail

piece (S11) and hand tighten.

2

3

S4

S11

PLUMBER

PUTTY

OPTIONAL

S5

S6

S9

S10

7) Turn tail piece (S11) and ange

(S4) so pivot is facing toward

faucet. Pull assembly down into

drain hole. Secure hardware to

assembly from below sink. Install

stopper (S1) in the removable or

non-removable position.

2

3

S11

PIVOT

S4

S1

Installation

D

4) Turn escutcheon (D) clockwise to

seal to deck surface.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621

Troubleshooting Chart

Finish is spotting.

Elements in water supply may cause

water staining on nish.

Clean nished trim area with a soft

cloth using mild soap and water or a

non-abrasive cleaner and then quickly

rinse with water.

9) Connect lift rod (A) to clevis strap

(S2) and secure with thumb screw

(S3). Insert pivot rod (S13) into

clevis strap (S2). Secure with

spring clip (S8) and adjust linkage

if necessary.

1

3

4

A

S8

S13

S2

2

S3

S2

10) Connect hoses (T) and supply

lines. Remove aerator (J) with

removal key (K) and ush lines

free of debris. Check for leaks.

4

1

J

K

T

Maintenance

1) Remove set screw (B). Turning

counter-clockwise, disassem-

ble handle (C) and nut (G) from

cartridge (H or I).

B

C

G

H

I

8) Attach sealing washer (S12), pivot

rod (S13) and cup washer (S14)

to tailpiece (S11). Hand tighten

nut (S7) clockwise to secure pivot

rod (S13).

S13

S11

1

S12

S14

S7

2

2) Remove cartridge (H or I) from

valve body (M). Inspect for debris.

Replace cartridge if neccessary.

M

H

I

3) Install cartridge and handle assembly

following steps 1 and 2 in reverse.

3

2

3

Note: Apply plumber tape to inlet

of shut off valves.

Installation

Page is loading ...

Symmons SLW-6612-1.0 Installation guide

This manual is also suitable for

Symmons SLW-6612-1.0 Installation guide

in other languages

Related papers

Other documents