Philips AJ260/93 Quick start guide

Category
Alarm clocks
Type
Quick start guide
AJ260
Clock Radio
QUICK START
快速指南
Thanks for buying Philips AJ260 clock radio.
Our Quick Start guides you through just some of the features on the set.
Please read our instruction booklet to really rise & shine!
Register your product and get support at
www.philips.com/welcome
C
A
B/3
3
R
B
DC 7.5V
R
ENGLISH
Step
A
Connect the supplied mains adapter to
the set
s 7.5V DC jack and the plug
into a wall outlet.
Step
B
How to set the Clock & Alarm
time
Press and hold
TIME SET
or
ALM1 /
ALM2
until the time digits flash.
Press and hold
TUNING +/-
to adjust
time.
Press
TIME SET
or
ALM1 / ALM2
to
confirm.
Repeat the
steps
2-3
to complete all the
other time items setting.
Step
C
Selecting the Alarm mode
In standby mode, slide the RADIO/BUZ to
select desired mode
Helpful hints:
If you have selected
RADIO
make sure
you have properly tuned to a station before
turning off the set.
3 ways to switch off the alarm
Either press briefly:
SLEEP/ALARM
RESET
or
REPEAT ALARM/
BRIGHTNESS CONTROL
.
Press
ALM1
or
ALM2
.
1.
2.
3.
4.
Radio
Press
RADIO ON/OFF
once to switch
on the radio.
Press
AUTO SCAN/DATE
to program
all available stations.
Press
PRESET
until the desired preset
station is displayed.
Weather forecast and Indoor
thermometer
The unit can auto detect and measure
atmospheric pressure changes to
graphically display the weather forecast
in the next 12 to 24 hours, and current
indoor temperature.
Note:
The weather forecast based on the
atmospheric pressure may vary slightly
from the actual weather situation.
Using the outdoor sensor
The outdoor sensor is supplied to work
with the main unit to measure and display
the outdoor temperature.
Place the sensor in a desired open area.
The place must be within 50 meters
away from the main unit. (Make sure
that the sensor is loaded with 2 AA
batteries.)
For therst
time using the outdoor
sensor and the main unit, press
RESET
located on the sensor back, and
RESET
located in the battery compartment of
the main unit. Then, the main unit will
begin to receive transmission from the
sensor.
1.
2.
3.
1.
AJ260_QSG.indd 1 2007-07-26 11:19:34 AM
To update the outdoor temperature
from the sensor any time, press and hold
AUTO SCAN/DATE
for 5 seconds.
Note:
Refer to the supplied User Manual for
more information about the outdoor
sensor.
中文
步骤
A
将电源适配器连接到本机的
7.5V DC
插口
将插头插到墙上的插座上
步骤
B
如何设置时钟和闹钟时间
按住
TIME SET
键或
ALM1 / ALM2
直至时间数字闪烁
按住
TUNING +/-
键调整时间
TIME SET
ALM1 / ALM2
重复
步骤
2-3
完成其它时间项设置
步骤
C
选择闹铃模式
在待机模式下
推动
RADIO/BUZ
键选择想
要的模式
提示
RADIO
关掉闹钟的
3
种模式
可以轻按
SLEEP/ALARM RESET
REPEAT ALARM/BRIGHTNESS
CONTROL
1.
2.
3.
4.
ALM1
ALM2
收音机
在收音机上按
RADIO ON/OFF
键一次或
多次
AUTO SCAN/DATE
键编辑所有可用
电台
PRESET
键直至想要的预设电台显示
天气预报和室内温度
本机能自动检测气压变化
用图示显示未来
12
24
小时内的天气形势和当前的室内温度
注意
天气预报基于气压变化
可能会与实际的天
气状况稍有差异
使用传感器检测户外温度
户外传感器配合主机工作
检测并显示户外的
温度
把传感器安置在所选的户外区域
该区域与
主机的距离应小于
50
务必确保在传感
器上装有
2
AA
型号电池
第一
使用传感和主机时
按下位于
器后部的
RESET
键和位于机电池盒
RESET
然后主机始接收传器传
任何时候需要更新传感器检测的户外温度
按住
AUTO SCAN/DATE
5
注意
有关户外传感器的更多信息
请参阅随机附
送的
使用说明
》。
1.
2.
3.
1.
C
A
B/3
3
R
B
DC 7.5V
R
Note
AJ260_QSG.indd 2 2007-07-26 11:19:35 AM
  • Page 1 1
  • Page 2 2

Philips AJ260/93 Quick start guide

Category
Alarm clocks
Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI