Whirlpool ACM 880 IX User guide

Brand: Whirlpool

Model: ACM 880 IX

Category: Kitchen & houseware accessories

Type: User guide

This manual is also suitable for

Whirlpool ACM 880 IX allows you to adjust the minimum flame of your gas hob to get the right simmering level for your sauces, prevent food from sticking and boiling over. It also enables you to put the finishing touches to your dishes directly on the hob, thanks to the grill burner that delivers intense heat.

INSTRUCTIONS FOR USE

INSTALLATION INSTRUCTIONS

BEFORE USING THE APPLIANCE

PRECAUTIONS AND GENERAL ADVICE

ENERGY SAVING TIPS

OVEN ACCESSORIES

CLEANING AND MAINTENANCE

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

For best use of the oven, carefully read the operating instructions and keep them for future

consultation.

INSTALLATION INSTRUCTIONS

Electrical connection

Before connecting the appliance, make sure:

the mains voltage in your home matches that specified on the appliance dataplate;

the electrical system adequate for appliance max. power absorption specified on the dataplate;

the house electrical system is suitably earthed.

• Connect the appliance to the power supply by means of a suitable disconnecting switch with

min. contact opening distance allowing complete disconnection in category III overvoltage

conditions, in compliance with the installation regulations.

Notes:

After installation, the electrical components must only be accessible with the use of a special tool.

The power cable must be H05VV-F type, in compliance with the table given below.

Connect a power cable of suitable section:

Instructions for the installer

Warning

• Disconnect the appliance from the power supply before carrying out any repairs or

operation.

• Installation must be carried out by a qualified technician, in compliance with the current

safety regulations.

• The appliance must be earthed.

The Manufacturer declines any liability for injury or damage to people or property due to non-compliance

with the above-mentioned regulations. The appliance dataplate is located at the bottom right of frame of

the oven cavity and visible with the door open. Adjustment conditions are given on a label on the packing.

Do not use the oven door for handling operations, or for removing the appliance from the packing.

Type of appliance Single-phase power supply

230V

Gas hob with gas oven Cable H05VV-F

Section 3 x 1 mm²

Gas connection

For information regarding gas connection instructions, see

the section on “standards” relevant to your country

(“References to National Regulations”).

The gas supply system must comply with current local

regulations.

The appliance must be connected to the gas supply or gas

bottle by means of a rigid copper or steel pipe with fittings

conforming to local regulations or by means of a continuous s/

steel hose conforming to local regulations.

The hose must not be longer than 2 m.

The hose must be connected directly to the elbow of the

outlet union (Fig.1).

Important: When using a hose, it must be installed so

that no part of it is contact with hot parts on the back of

the appliance or cooker. Its path must be free of any

hindrances and in a place where it can be inspected along

the entire length (Fig. 2).

When the appliance is connected to the gas supply, use soapy

water to check for gas leaks.

Fig. 2

Fig. 1

Installation

Important

: The covering of the cabinets must be in heat resistant (min. 90°C)

material.

If the appliance is installed next to kitchen cabinets, ensure the minimum clearances indicated in the

following figure.

There are certain points to pay attention to when positioning the cooker. Make sure to take into

consideration the following recommendations, in order to prevent any problems and hazardous

situations that may occur!

The cooker can be positioned near other cabinets provided their height does not exceed the hob level.

In selecting a position for the cooker, make sure the appliance is not placed next to a refrigerator and

that there are no flammable or combustible materials in the vicinity, such as curtains, etc. which can

quickly catch fire.

A minimum space of 20 mm between the metal rear cover of the cooker and the wall is required to

ensure air circulation.

If the counter tops are higher than hob level, they should be at least 110 mm from the sides of the cooker.

To fit them, tilt the appliance and screw the 4 feet in the special threads located in the corners

(see Fig. 2).

Fig. 2

Max.

adjustment

15 mm

Fig. 1

Min. 65 cm

Min. 50 cm (depending on the model)

ELECTRICAL CONNECTION AND SAFETY

For the electrical connection, make sure to follow the

instructions given below:

•

The earth wire must be connected to the earth terminal ( ).

If there is no approved earthed electrical outlet in the place

where the appliance is to be installed, immediately contact to

our Authorised Service.

•

The earthed electrical outlet must be close to the appliance.

Do not use extension cords.

•

The power cable must not touch hot parts of the product.

•

If the power cable is damaged, contact a Qualified Service

Centre. The cable must be replaced by the Authorised

Service.

•

An incorrect electrical connection could damage your

appliance. Such damage is not covered by the warranty.

•

The appliance is arranged for a 230 Volt power supply. If the

power supply voltage is different, immediately contact to our

authorised service.

The power cable must not touch hot parts of appliance.

Otherwise it may become damaged.

This situation could cause short circuiting.

The manufacturer declines any liability for damage and loss due to

failure to comply with the following safety regulations

If replacing the power cable, the new one must have the same

characteristics that are specified in this manual.

To replace the cable, proceed as follows:

•

open the terminal board box;

•

undo the cable fixing screw

;

•

loosen the screw contacts and replace the cable with one of

the same length, complying with the table in the section

“Electrical connection”;

•

the

Yellow/Green

earth wire must be connected to the

terminal and be approx. 20 mm longer than the line wires;

•

the

Blue

neutral wire must be connected to the terminal

marked with the letter

;

•

the live wire must be connected to the terminal marked with

the letter

Electrical Connection Diagram

Provision for room ventilation

This appliance is not connected to a fume exhaust device.

Therefore it must be installed and connected in compliance with

current installation regulations.

Particular attention must be paid to the applicable standards

concerning room ventilation.

Room ventilation

This appliance must only be installed and used in well-

ventilated rooms, in compliance with the current and local

regulations, with openings in the walls or with special ducts

enabling adequate natural or forced ventilation, and

ensuring the air necessary for correct combustion and air

change.

In particular, if there is only this gas appliance in the room, a hood

must be installed above it to ensure natural and direct extraction,

with a straight vertical duct of length equal to at least twice the

diameter and a minimum section of at least 100 cm

For the inlet of fresh air into the room, a similar opening of at least

100 cm

directly to the outside must be provided at a suitable

height from the floor so as not to be obstructed on the inside or

outside of the wall and not to hinder the correct combustion of

the burners and the regular extraction of vitiated air, and with a

height difference of at least 180 cm with respect to the outlet

opening.

The quantity of air necessary for combustion must not be less

than 2 m

/h for every kW of power (see total power in kW on the

appliance dataplate).

In all other cases, when there are other appliances in the same

room, or when direct natural ventilation is not possible and

indirect natural ventilation or forced ventilation is required,

contact a qualified specialist for carrying out installation and

preparing the ventilation system in strict compliance with the

current regulations.

Flues already used by other appliances must not be used for the

fume exhaust.

Air inlet section

min. 100 cm

Air outlet section

min. 100 cm

Air inlet section

min. 100 cm

Air inlet section

min. 100 cm

Electric fan

Cooker hood

flue

Gas adjustments

The hose must be connected as shown in Fig. 1 and 2, in

compliance with the local regulations.

Natural gas

Use outlet union GN for natural gas.

The hose must be connected to the outlet union and secured

using hose clamp B (Fig. 1). A mechanical connection can also be

used where appropriate. To make this connection, remove the

NG nut from the tip of the manifold. Place the extra seal that is

placed in the injector set on the connector to the appliance, and

then assemble the connector to the appliance. The connector to

the appliance must be ½” threaded female.

Butane/Propane gas

Use outlet connector B/P for Butane/Propane gas. The hose must

be connected to the outlet union and secured using hose clamp B

(Fig. 2).

The hose must not be longer than 2 m. It must be a standard hose

and replaced within the date printed on it.

Important:

Close the gas supply cock before carrying out any

maintenance operation.

Connection details: see the specific regulations for your country.

Use pressure regulators that are suitable for the gas

pressure values given on the Product Description Sheet

supplied separately.

If the appliance is arranged for a type of gas different from that

available, it is necessary to change the injectors, adjust the

minimum flame and change the outlet union.

Carry out the following operations to change the hob injectors:

remove the pan supports, remove the burners and burner caps

(see Fig. 3); change the injector (Fig. 4) and replace it with one

suitable for the new type of gas (see table on the separate Product

Sheet).

Replace the gas setting label with the new one

included in the injector bag.

Refit everything by proceeding in reverse order, making sure to

correctly fit the burner cap on the burner.

Replacing oven and grill burner injectors:

To replace the oven and grill burner injectors:

Remove the oven and grill burners by undoing the fixing screws

located on the tip of the burner.

Remove the existing injectors on the injector (Fig. 5) holder and

replace them with the new ones supplied in the spare set.

Minimum for hob taps

NB: The appliance injectors must be replaced by an

authorised technician.

For appliances equipped with Flame Failure Devices and

microswitches, the control panel must be removed in order to

safely access the adjusting screw.

To adjust the minimum flame, proceed as follows

•

Light the burner and turn the knob to min. ; remove the tap

knob (Fig. 6). Insert a small screwdriver in the tap pin (Fig. 7).

Turn the adjustment screw anticlockwise to increase the flame,

or clockwise to decrease it. Adjustment is correct when the flame

is approx. 3 - 4 mm.

The adjustment screw must be completely screwed down for

butane/propane gas.

Make sure the flame does not go out when switching straight

from high to low flame and vice versa.

Refit the knob.

Fig. 3

Fig. 4

Fig. 1 Fig. 2

Fig. 5

Fig. 6

Fig. 7

BEFORE USING THE APPLIANCE

•

Remove the accessories from the oven and heat

it at 200°C for about two hours to eliminate the

smell of protective grease and insulating

materials. Keep the window open during this

operation.

•

Before use, remove:

- stickers located on the front of the appliance

and on the oven door, except the dataplate;

- cardboard protection and protective plastic

film on the control panel and other parts of

the appliance;

- any stickers on the accessories

(e.g. under the drip-tray).

1. Packing

The packing material is completely recyclable, and

is marked with the recycling symbol , which

identifies it as a type of material that must be sent

to local waste-disposal centres.

2. Product

This appliance is marked in compliance with

European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE).

By ensuring that this appliance is correctly

scrapped, the user can help prevent potentially

harmful consequences for the environment and the

health of people.

The symbol on the appliance or accompanying

documentation indicates that this product must not

be treated as household waste, but must be taken

to a collection centre for the recycling of electrical

and electronic appliances.

Disposal must be carried out in accordance with

the local environmental regulations on waste

disposal.

For more detailed information about the

treatment, recovery and recycling of this product,

please contact your competent local authority, the

household waste collection service or the shop

where you purchased the appliance.

Oven minimum flame adjustment

Light the oven burner at max. setting.

Close the door. Turn the knob to min. After approx. 20 minutes

(at least to obtain first activation of the thermostat), proceed as

follows: remove the oven knob and insert a small screwdriver

under the thermostat, as shown in the figure.

Turn the adjustment screw clockwise to increase the flame and

anticlockwise to decrease it. For correct setting, make sure the

flame height is 3/4 mm.

PRECAUTIONS AND GENERAL ADVICE

•

The appliance is designed solely for domestic

use for cooking food. No other use is allowed.

The Manufacturer declines all liability for

inappropriate use or incorrect setting of the

controls.

•

Any repairs or adjustments must be carried out

exclusively by a qualified technician.

•

Never expose the oven to atmospheric agents.

•

Do not place heavy objects on the door as they

could damage the oven compartment and

hinges. Do not cling to the door.

•

Do not hang anything heavy on the oven door

handle.

• Do not cover the oven floor with aluminium

foil or other objects.

•

The oven door must close properly. The door

seals must be kept clean.

•

Do not pour water directly inside a hot oven. The

enamel coating could become damaged.

•

Fruit juice dripping from the baking tray may

leave permanent stains. It is advisable to clean

the appliance before reusing it.

•

To prevent the oven coating from being

scratched, do not drag pots and pans across the

bottom of the oven.

•

The accessible parts of the appliance may

become very hot during use. Keep children

away.

•

Never use abrasive materials or substances to

clean the GLASS, as they could damage it.

•

The unit becomes very hot during use. Do not

touch the heating elements in the oven.

•

Residual condensation after cooking could

eventually damage the oven and surrounding

kitchen units. We recommend that you:

- set the lowest temperature;

- cover food;

- remove food from the oven;

- dry wet parts when the oven is cool.

• Caution: The front panel and oven door

handle become hot when the appliance is

used for a long time at high temperatures.

•

Do not touch the appliance with wet parts of the

body or use it when barefoot.

•

Do not pull the appliance or the power cable to

unplug it.

• Do not allow children to touch:

- the controls and the appliance in general,

especially during and immediately after use:

risk of injury;

- packing (bags, polystyrene, metal parts,

etc.);

- any appliance to be scrapped.

•

The appliance is not intended for use by children

or persons with limited physical, sensory or

mental abilities or without experience and

knowledge of it, unless they are under the

supervision of or instructed in its use by a person

responsible for their safety.

•

Make sure the electrical cables of any other

appliances used near the oven do not touch hot

parts or get caught in the oven door.

•

Do not place flammable materials in the oven or

nearby, due to the risk of fire if the oven is

inadvertently switched on.

•

Use oven gloves to remove pans and accessories

when the oven is hot.

•

If alcoholic beverages (e.g. rum, cognac, wine,

etc.) are added when roasting or baking cakes,

etc., remember that alcohol evaporates at high

temperatures. Vapours released by the alcohol

may catch fire on coming into contact with the

operating gas burner.

•

Do not heat or cook foods in closed containers.

The pressure created inside could cause them to

explode, damaging the oven.

•

Do not use containers made of synthetic

material for cooking (except for packages

specifically designed for this purpose; see the

manufacturer's instructions). They could melt at

high temperatures.

•

Always pay attention when cooking with oil and

grease. Oil and fat can overheat and catch fire!

•

Never pull out fully loaded shelves. Use extreme

caution.

DECLARATION OF CONFORMITY

• This appliance is suitable for contact with

foodstuffs and complies with EEC (EC)

Regulation no. 1935/2004.

• This appliance is designed for cooking only.

Any other use (e.g. for room heating) is

deemed improper and potentially

dangerous.

• This appliance has been designed,

manufactured and marketed in compliance

with:

- the safety requirements of EEC Gas

Directive 90/396;

- the safety objectives of Low Voltage

Directive 2006/95/EC (which replaces

73/23/EEC as amended).

- the protection requirements of EMC

Directive 89/336/EEC;

- the requirements of Directive

93/68/EEC.

ENERGY SAVING TIPS

OVEN ACCESSORIES

•

The hob is equipped with burners of different diameters. Use pots and pans of bottom width equal to

that of the burners or slightly larger.

•

Only use flat-bottomed pots and pans.

•

Pots and pans must not protrude over the control panel.

•

If possible, keep pans covered when cooking.

•

Cook vegetables, potatoes, etc. with a small amount of water in order to reduce cooking time.

Using a pressure cooker will further reduce energy consumption and cooking time

The accessories supplied depend on the model. The

accessories provided with the oven are listed in the

Product Description Sheet provided separately (under

Accessories).

Wire shelf (1)

The wire shelf can be used to grill food or as a support for baking

trays, cake tins and other cooking containers. It can be placed on

any of the runners in the oven.

Baking tray (2)

For baking biscuits, cakes and pizzas.

This tray can also be used for collecting fat and any scraps of

food when placed under the grill; pour a little water in the drip-

tray to prevent spatters of fat and smoke.

Flap panel (depending on the model) (3)

To open accessory flap panel, pull the upper part of the flap

panel as illustrated.

Caution:

When the oven is in use, the inside walls of the accessory drawer

and the metal accessories in the drawer become very hot.

Use oven gloves when removing the accessories.

Knob guard (4)

It protects the knobs against overheating during use of the grill.

Turnspit (5)

Use the turnspit as indicated in the relevant chapter in the

Product Description Sheet supplied separately.

Burner Max. diameter of pan

Rapid (100 mm)

Semirapid (75 mm)

Auxiliary (55 mm)

220-260 mm

140-220 mm

120-180 mm

Fig. 1

Fig. 2

Fig. 3

Fig. 4

Fig. 5

CLEANING AND MAINTENANCE

Important: When cleaning the cooker, do not shift it

beyond the length of the tube.

Disconnect the appliance from the power supply before

carrying out any cleaning operation.

•

Clean using a cloth moistened with warm soapy water or

diluted liquid detergent.

•

Do not use abrasive, corrosive or chlorine products, or steel

wool.

•

Do not use steam cleaners.

•

Do not use flammable products.

•

Do not leave acid or alkaline substances such as vinegar, salt,

lemon juice, etc., on the hob.

Stainless steel surface

•

Clean with a specific commercial product.

Cleaning the burners

To clean the hob burners, lift them out of their seats (Fig. 1) and

place in a solution of hot water and non-abrasive detergent for

about 10 minutes. After cleaning and washing the burners,

thoroughly dry them.

Always make sure the openings are not blocked.

It is

advisable to carry out this operation at least once a week or

whenever necessary. Make sure to properly refit the burners,

turning them slowly so that the burner caps engage in the injector

holder seat (if perfectly centred, the burner lowers a little and

locks in place).

Pan support maintenance

•

Clean the pan supports with a sponge and detergent

whenever dirty.

•

The pan supports will change colour near the burners. This is

perfectly normal and is due to the high temperature reached

during cooking.

Oven cleaning

•

After cooking, wait for the oven to cool then clean it to

prevent the accumulation of cooking residuals.

•

For stubborn grime, use a specific oven cleaning product,

following the instructions given on the package.

•

Clean the outside of the oven with a sponge and lukewarm water.

•Do not use abrasive products or steel wool.

•

Clean the door glass with a liquid detergent.

•

Soak the accessories in water with washing up detergent

immediately after use. Food residues can be easily removed

using a brush or sponge.

Removing the side grids (depending on models)

Grip the bottom part of the side grids and pull towards the middle

of the oven. Lift upwards to completely remove.

Pull the side grid as shown in the picture (fig. 2). After releasing it

from clips, lift up.

Carry out the above steps in reverse order to refit the side grid.

Caution:

After cleaning, be sure that the grids are fitted in their

original sides. The notches on the grids must be close to the front,

not rear.

Fig. 1

Fig. 2

Burner cap

Burner head

Burner base

Removing the door

Caution: When carrying out the following operations it is

advisable to wear protective gloves. Carefully follow these

instructions to prevent injury and/or damage to the oven

door and hinges.

Pay attention to the oven door hinges: risk of injuring

hands!

Open the oven door

Fully open the saddle brackets

While opening the saddle brackets, use a metal tool such as

handle side of a spoon for easy opening.

Close the door almost completely (Fig. 2), and remove by pulling

it outwards.

NOTE:

Proceed in reverse order to refit the door. Make sure the

saddle brackets are lowered before closing the oven door.

Replacing the rear oven lamp:

Disconnect the oven from the power supply.

After the oven has cooled down, unscrew (anticlockwise) the

lamp cover

(Fig. 3).

Replace the lamp (see note).

Refit the lamp cover.

Reconnect the oven to the power supply.

Note: Only use 25 W/230 V E-14 type T300°C lamps

available from the After-Sales Service.

Important: Do not use the oven until the lamp cover has

been refitted.

Fig. 1

Fig. 2

saddle

bracket

(see detail A)

saddle

bracket

DETAIL A

Fig. 3

TROUBLESHOOTING GUIDE

1. The appliance does not work:

•

Check the mains power supply and that the

appliance is electrically connected

•

Switch the appliance off and on to see if the

problem persists.

2. The burner fails to ignite:

•

Is the main gas delivery valve open?

•

Has the delivery of the town gas (methane) been

suspended?

•

Is the gas cylinder (liquid gas) empty?

•

Are the openings of the burner clogged?

•

Have the cap and burner been positioned

correctly after cleaning? (See paragraph “Care

and Maintenance”.)

3. The burner fails to remain lit:

•

Repeat the ignition operation, turning the knob

to the position with the small flame symbol .

AFTER-SALES SERVICE

Before calling the After-Sales Service

See if you can eliminate the problem on your

own (see “Troubleshooting Guide”).

Switch the appliance off and on again to see if the

problem persists.

If the fault persists after the above checks,

contact your nearest After-Sales Service.

Specify:

•

the type of fault;

•

exact type and model of oven;

•

the After-Sales Service number (the number

given after the word “Service” on the dataplate)

located at the bottom right of frame of the oven

cavity and visible with the door open. The

service number is also given in the warranty

booklet;

•

your full address;

•

your telephone number.

For repairs, contact an

Authorised After-Sales

Service

, indicated in the warranty.

If any work is carried out by technicians not

belonging to the Manufacturer's authorised After-

Sales Service centres, request a receipt specifying

the work performed and make sure the

replacement parts are

original.

Failure to comply with these instructions can

compromise the safety and quality of the product.

Whirlpool ACM 880 IX User guide

Brand: Whirlpool

Model: ACM 880 IX

Category: Kitchen & houseware accessories

Type: User guide

This manual is also suitable for

Download PDF

report

Whirlpool ACM 880 IX User guide

This manual is also suitable for

Whirlpool ACM 880 IX User guide

Related papers

Other documents