LG PMC-1000 User manual

USER MANUAL

Portable Charger

Rev 1.0 EU

PMC-1000

USER MANUAL

Portable Charger

PMC-1000

ENGLISH

2

Safety Precautions

Disassembling the product may cause malfunction of the product.

Please do not disassemble the product.

LG Electronics is not responsible for problems caused by disassembling

the product by users or non-authorized personnel.

Please read the safety information carefully before using the product.

After reading this manual, make sure to keep it in a place where you can

easily access while using the product.

• Please don’t use the portable charger in a place which often produces

static electricity and heat. It can cause breakdown and failure.

• Please don’t use the portable charger in a place which is really damp

and/or dusty. It can cause breakdown and failure.

• Please don’t disassemble, convert, and/or repair. It can cause

breakdown and failure and will void warranty.

• Please don’t spill water, oil and/or chemicals on product. It can cause

breakdown and failure.

• Please check that device’s voltage is compatible with your product.

• To prevent failure, malfunction and danger of an explosion, please do

not leave your product around a heat source or combustible material.

•Do not shake or throw the product.

•When the product has damage, don’t turn on.

•When not in use, please charge the product once a month.

•Ifinternaluidsoftheproductcomeintocontactwithskin,rinsewith

clean water immediately. This can cause irritation to your skin.

• Please do not press or bend the charging cable. This can cause failure

or malfunction.

Getting Started

3

• Do not leave the product in/around heating appliances, car interiors,

or high temperature environments. May cause overheating and/or

explosion.

• If product emits smoke or a strange smell, stop use immediately. It may

causereorelectricshock.

•Please leave the product out of the reach of children or babies.

• Do not put the product in the microwave or oven. Rapidly heating the

productcancausedamage,overheating,re,explosion.

• Please immediately discontinue use if there is strange odor, heating,

discoloration, and other strange phenomenon while using the product.

The product may overheat, combust, or explode.

• Please do not give the product strong impact or drop. The product may

overheat, combust, or explode.

• Do not apply pressure or puncture the portable charger. The product

may overheat, combust, or explode.

•Donotexposetohightemperatureover60˚C.Thiscancause

overheating,re,orexplosion.

• Do not leave or use in high temperature and humidity such as a

bathroom. The product may overheat, combust, or explode.

• Please do not step on or press cables. If the cable is broken, do not

use.Itmaycauseelectricalshock,orre.

•Donotusenearameorammablematerial.Theproductmay

overheat, combust, or explode.

• Do not plug metal objects into the body. The product may overheat,

combust, or explode.

• Do not use the product for a long time on a blanket or quilt, electric

blanket, or on the carpet. The product may overheat, combust, or

explode.

4

• Li-ion Battery is a hazardous component which can cause injury.

•Batteryreplacementbynon-qualiedprofessionalcancausedamage

to your device.

• Do not replace the battery by yourself. The battery can be damaged,

which can cause overheat and injury. The battery must be replaced

by the authorized service provider. The battery should be recycled or

disposed separately from household waste.

Recycling / disposal : Product must be disposed of properly. Do not

throw it in the trash or incinerator.

5

Appearance

a

b c d

Port A

Port B

a USB port for charging portable device (5 V Output)

b LED

You can check remaining battery capacity when you press the LED

button. Lighting the LEDs represent current battery capacity.

c Micro USB port for charging portable charger (Input)

d LEDbutton(Chargingstartbutton)

PMC-1000

LED O O O O O O

Capacity ≤30% 30~70% 70~100%

CAUTION

• Please charge the portable charger at least once a month, because it

consumes a small amount of current even when not in use.

,

NOTE

• Actual product design may differ from images shown in this manual.

6

Charging the Portable Charger

CAUTION

Chargetheportablechargercompletelybeforeusingitforthersttime.Before

connecting the USB cable, check the voltage/current of the adapter. If you use

unsuitable device, it may cause malfuction of portable charger or charger.

1.ConnecttheMicroUSBport(Input)oftheportablechargerandthe

chargeradapterorPCUSBportbyusingtheUSBcable.

- The LED is blinking, it is charging normally.

2. When charging of the portable charger is done, the LED indicator will

be turned on. Then, remove the USB cable.

,

NOTE

• LED lights display charging conditions and capacity indications. For more

details, refer to LED conditions on page 5.

• When you press LED button while in charging battery, the portable charger

mode change to discharging mode for portable device and stop the charging

during 20 seconds. After 20 seconds, the portable charger will be charged

normally.

Operation

7

Sequential Charging

1.ConnecttheMicroUSBport(Input)oftheportablechargerandthe

charger adapter by using the USB cable.

2.ConnecttheUSBport(Output,PortA)oftheportablechargerandthe

USB port of your portable device by using the USB cable.

- Afternishingtheportablechargercharged,thenyourportable

device will be charged.

- WhenyoupressLEDbutton,afternishingyourportabledevice

charged, then the portable charger will be charged.

Depending on Portable device, charging process might not stop

eventhoughbatteryisfullycharged(100%charged).Inthis

case, it will be not switched to charging the portable charger. In

order to change the sequence for charging the portable charger,

please wait for some time(it may different depending on device’s

manufacturer.) or disconnect the portable device from portable

charger.

3.Whenchargingofportabledeviceisdone,removetheUSBcable.

* If simultaneously charging the mobile device and portable charger,

connecttheportablecharger’sUSBoutputport(1,PortB)toyour

mobile device’s USB port.

,

NOTE

• When sequential charging function is operated, charging current will be

limited. Thus, it may take longer to charge.

• This function is recommended to use genuine charger. If you charge by using

USBportinPC,itmaynotbecharged.

8

• If disconnecting the charger while charging portable device(product to be

charged) by using sequential charging, the portable device will be charged.

• If disconnecting a portable device while charging portable device (product

to be charged) by using sequential charging, the portable charger will be

charged about 20 seconds later.

• If doing sequential charging within 20 seconds since the LED button has

been pressed, the portable charger will be charged after the portable device

is charged completely.

• If connecting the charger to the portable charger while charging a portable

device, the portable charger will be charged after the portable device is

charged completely.

Charging Portable Devices

CAUTION

Checkthevoltage/currentspecicationwithyourportabledevicebefore

charging the portable device.

Checkmanualorchargerspecicationthatyoupurchasedportabledeviceor

check manufacturer of portable device before you charge the portable device.

1.ConnecttheUSBport(Output)oftheportablechargerandtheUSB

port of your portable deivce by using the USB cable.

2. Press the LED button.

- LEDsashingrepresentscurrentbatterycapacity.

3.Whenchargingofportabledeviceisdone,removetheUSBcable.

9

,

NOTE

• You can use the supplied USB cable with your portable device to charge.

• If not connecting a portable device to the portable charger after pressing the

LED button, the portable charger output is to be turned off about 20 seconds

later.Chargingmodeforportabledevicewillmaintainduring20seconds.

• Available accessories may vary depending on your region, country or service

provider.

10

Please check the following contents if portable charger does not work.

If the problem is not solved, please stop use and contact manufacturer.

Problem Cause & Correction

Portable charger

cannot charge the

portable device.

•PleasechecktheVoltagespecication

between Portable charger and the portable

device.

• Please check that the cable is properly

connected.

• Please start charging the portable device

by pressing the LED indicator button.

There is no LED

ashingafter

connecting the

portable charger to the

portable device.

• The charging status will start with LED

ashingafterpressingtheLEDindicator

button.

•LEDdoesn’tashwhiletheportable

charger charges the portable device.

LED is not blinking,

while portable charger

is charging using a

laptop or desktop.

•PleasecheckthatthePCisinpoweroffor

sleep mode.

• The USB port may lack power. Please

disconnect all other devices using USB

ports.

Troubleshooting

11

Problem Cause & Correction

There is no LED

lighting when the LED

indicator button is

pressed.

The portable charger

is not charging the

portable device.

• The portable charger is almost empty.

Please charge it.

• It can appear when safety-circuit was

operated by a short-circuit. For normal

operation, disconnect the portable charger

withthecablerstandthenchargethe

portable charger again.

The charging time is

too long.

• The charging time may vary due to

environmental temperature. (Please charge

in5°Cto35°C(41°Fto95°F))

• The charging time may vary when the

portablechargerisconnectedtoPCUSB

ports.(USBspecication:5V500mA)

• The USB port may lack power. Please

disconnect all other devices using USB

ports.

•

May occur when using a USB Hub. Please

connectportablechargertoPCUSBport

directly.

The portable charger

is overheating.

• The portable charger may emit heat while

charging or during use, if there is too much

heat or smoke, please stop use.

12

Problem Cause & Correction

All LED keeps blinking

fast.

• In case of abnormal

circumstance

- Using the unit

at too much low

degree(below5°C

(41°F))ortoomuch

high degree(above

35°C(95°F)).

- An operation of

a short circuit

by external

environment.

- Input or output to

an overcurrent or

overvoltage.

• That means it is an abnormal

circumstance or a short circuit of the unit

occurs. Stop using the unit immediately.

If you make the normal circumastance, it

will work properly again.

• If the unit does not work properly even

under the normal circumstance for long,

press the LED button once.

• If the LED Lights keep blinking fast under

the normal circumstance, contact the

service center.

• It will work properly that you should

disconnect the charger from the portable

chargerrstandthenre-connectthem.

13

Specications

Model PMC-1000

Rated input

Max.DC5V0 2A

Rated output

Max.DC5V03A(thetotalcurrentof2ports)

Battery capacity

DC3.63V010,000mAh(Li-Ion)

Battery type Lithium-ion

Chargingtime 6.5 Hrs (Using 2 A charger)

Operating

temperature

5°Cto35°C

Size

(L x W x H)

91x61x22.4mm

Weight 192g

• Depending on the remainded capacity of the portable charger, the temperature

and charging circumstance, the charging time could be different.

• Designandspecicationsaresubjecttochangewithoutnotice.

Appendix

14

Conditions

- The warranty is valid only if the original receipt issued to the original purchaser

by the dealer, specifying the date of purchase and serial number, is presented

with the product to be repaired or replaced. LG Electronics reserves the right to

refuse warranty service if this information has been removed or changed after

the original purchase of the product from the dealer.

- If LG Electronics repairs or replaces the product, the repaired or replaced

product shall be warranted for the remaining time of the original warranty period

orforninety(90)daysfromthedateofrepair,whicheverislonger.Repairor

replacement may involve the use of functionally equivalent reconditioned units.

Replaced parts or components will become the property of LG Electronics.

- This Warranty does not cover any failure of the product due to normal wear and

tear, or due to misuse, including but not limited to use in other than the normal

and customary manner, in accordance with instructions for use and maintenance

oftheproduct.Nordoesthiswarrantycoveranyfailureoftheproductdueto

accident,modicationoradjustment,actsofGodordamageresultingfrom

liquid.

- This warranty does not cover product failures due to improper repair,

installations,modicationsorserviceperformedbyanon-LGElectronics

authorized person. Tampering with any of the seals on the product will void the

warranty.

Limited Warranty

SUBJECTTOTHECONDITIONSOFTHISLIMITEDWARRANTY,LG

ELECTRONICSWARRANTSTHISPRODUCTTOBEFREEFROMDEFECTS

INDESIGN,MATERIALANDWORKMANSHIPATTHETIMEOFITSORIGINAL

PURCHASEBYACONSUMER,ANDFORASUBSEQUENTPERIODOF

ONE(1)YEAR.SHOULDYOURPRODUCTNEEDWARRANTYSERVICE,

PLEASERETURNITTOTHEDEALERFROMWHOMITWASPURCHASED

ORCONTACTYOURLOCALLGELECTRONICSCONTACTCENTERTOGET

FURTHERINFORMATION.

15

Removal of waste batteries and accumulators

(Product with embedded battery ONLY)

- In case this product contains a battery incorporated within the product which

cannotbereadilyremovedbyend-users,LGrecommendsthatonlyqualied

professionals remove the battery, either for replacement or for recycling at the

end of this product’s working life.

To prevent damage to the product, and for their own safety, users should not

attempt to remove the battery and should contact LG Service Helpline, or other

independent service providers for advice.

- Removal of the battery will involve dismantling of the product case,

disconnection of the electrical cables/contacts, and careful extraction of the

batterycellusingspecializedtools.Ifyouneedtheinstructionsforqualied

professionals on how to remove the battery safely, please visit http://www.lge.

com/global/sustainability/environment/takeback-recycling.

DECLARATION OF CONFORMITY

Hereby,LGElectronicsdeclaresthatthisPMC-1000isincompliance

with the essential requirements and other relevant provisions of Directive

2014/30/EU.AcopyoftheDeclarationofConformitycanbefoundat

http://www.lg.com/global/declaration

16

Contact ofce for compliance of this product

LGElectronicsEuropeanSharedServiceCenterB.V.

Krijgsman1,1186DMAmstelveen,TheNetherlands

Disposal of waste batteries/accumulators

1 This symbol may be combined with chemical symbols for mercury

(Hg),cadmium(Cd)orlead(Pb)ifthebatterycontainsmorethan

0.0005%ofmercury,0.002%ofcadmiumor0.004%oflead.

2 All batteries/accumulators should be disposed separately from the

municipal waste stream via designated collection facilities appointed by

the government or the local authorities.

3 The correct disposal of your old batteries/accumulators will help to

prevent potential negative consequences for the environment, animal

and human health.

4 For more detailed information about disposal of your old batteries/

accumulators,pleasecontactyourcityofce,wastedisposalserviceor

the shop where you purchased the product.

Disposal of your old appliance

1 This crossed-out wheeled bin symbol indicates that waste electrical

and electronic products (WEEE) should be disposed of separately

from the municipal waste stream.

2 Old electrical products can contain hazardous substances so correct

disposal of your old appliance will help prevent potential negative

consequences for the environment and human health. Your old

appliance may contain reusable parts that could be used to repair

other products, and other valuable materials that can be recycled to

conserve limited resources.

3 You can take your appliance either to the shop where you

purchased the product, or contact your local government waste

office for details of your nearest authorised WEEE collection point.

For the most up to date information for your country please see

www.lg.com/global/recycling

Page is loading ...

MANUAL DE USUARIO

Cargador portátil

ESPAÑOL

PMC-1000

Page is loading ...

PODRĘCZNIK UŻYTKOWNIKA

Ładowarka przenośna

WERSJA POLSKA

PMC-1000

Page is loading ...

MANUAL DO UTILIZADOR

Carregador portátil

PORTUGUÊS

PMC-1000

Page is loading ...

LG PMC-1000, PowerTank PMC-1000 User manual

Related papers

Other documents