LG PMC-610 User manual

Rev 2.0 RU

www.lg.comPMC-610

USER MANUAL

Portable Charger

ENGLISH

РУССКИЙ ҚАЗАҚША

Page is loading ...

PMC-610

USER MANUAL

Portable Charger

ENGLISH

Page is loading ...

1

ENGLISH

Getting Started

Safety Precautions

Disassembling the product may cause malfunction of the product.

Please do not disassemble the product.

LG Electronics is not responsible for problems caused by disassembling

the product by users or non-authorized personnel.

Please read the safety information carefully before using the product.

After reading this manual, make sure to keep it in a place where you

can easily access while using the product.

• Please don’t use the portable charger in a place which often produces

static electricity and heat. It can cause breakdown and failure.

•Please don’t use the portable charger in a place which is really damp

and/or dusty. It can cause breakdown and failure.

•Please don’t disassemble, convert, and/or repair. It can cause

breakdown and failure and will void warranty.

•Please don’t spill water, oil and/or chemicals on product. It can cause

breakdown and failure.

•Please check that device’s voltage is compatible with your product.

• To prevent failure, malfunction and danger of an explosion, please do

not leave your product around a heat source or combustible material.

•Do not shake or throw the product.

•When the product has damage, don’t turn on.

•When not in use, please charge the product once a month.

•Ifinternaluidsoftheproductcomeintocontactwithskin,rinse

with clean water immediately. This can cause irritation to your skin.

2

ENGLISH

•Please do not press or bend the charging cable. This can cause

failure or malfunction.

•Do not leave the product in/around heating appliances, car interiors,

or high temperature environments. May cause overheating and/or

explosion.

•If product emits smoke or a strange smell, stop use immediately.

Itmaycausereorelectricshock.

•Please leave the product out of the reach of children or babies.

•Do not put the product in the microwave or oven. Rapidly heating

theproductcancausedamage,overheating,re,explosion.

• Please immediately discontinue use if there is strange odor, heating,

discoloration, and other strange phenomenon while using the product.

The product may overheat, combust, or explode.

•Please do not give the product strong impact or drop. The product

may overheat, combust, or explode.

•Do not apply pressure or puncture the portable charger. The product

may overheat, combust, or explode.

•Donotexposetohightemperatureover60˚C.Thiscancause

overheating,re,orexplosion.

•Do not leave or use in high temperature and humidity such as a

bathroom. The product may overheat, combust, or explode.

•Please do not step on or press cables. If the cable is broken, do not

use.Itmaycauseelectricalshock,orre.

•Donotusenearameorammablematerial.Theproductmay

overheat, combust, or explode.

3

ENGLISH

•Do not plug metal objects into the body. The product may overheat,

combust, or explode.

•Do not use the product for a long time on a blanket or quilt, electric

blanket, or on the carpet. The product may overheat, combust, or

explode.

•Li-ion Battery is a hazardous component which can cause injury.

•Batteryreplacementbynon-qualiedprofessionalcancause

damage to your device.

•Do not replace the battery by yourself. The battery can be damaged,

which can cause overheat and injury. The battery must be replaced

by the authorized service provider. The battery should be recycled or

disposed separately from household waste.

•Donotplacengersorhandsinsidetheproduct.

•Do not expose power bank to rain or snow.

• Use of a power supply or charger that is not recommended or sold

bythemanufacturerofthepowerpackmaycausereorinjuryto

persons.

•Do not us the power bank in excess of its output rating. Overloading

outputsabovetheratingmaycausereorinjurytopersons.

•Donotusethepowerbankifitisdamagedormodied.Damagedor

modiedbatteriesmayexhibitunpredictablebehaviour,whichcan

resultinre,explosionorinjury.

Recycling / disposal : Product must be disposed of properly. Do not

throw it in the trash or incinerator.

4

ENGLISH

Device Layout

a

b

c

d

e

a LED button (Check battery capacity status)

b LED indicator

You can check the remaining battery capacity by pressing the LED

button (1). The current battery capacity will be represented by the

LED indicator light (see the table below).

c Micro USB port for charging the portable charger (Input)

d USB port for charging mobile device (QC 3.0 Output)

e USB Cable

Charging adapter is not included with the product.

!

NOTE

PMC-610

LED indicator

Capacity ≤30% 30~70% 70~100%

Please charge the portable charger at least once a month because it

consumes a small amount of current even when not in use.

!

CAUTION

5

ENGLISH

Actual product design may differ from images shown in this manual.

!

NOTE

Operation

Charging the Portable Charger

Chargetheportablechargercompletelybeforeusingitforthersttime.

Before connecting the USB cable, check that the voltage/current of the

adapter is compatible with your device. If you use a charging device with

inadequate voltage/current, it may cause the charging device or the portable

charger to malfunction.

!

CAUTION

1. Using the USB cable, connect the charging adapter or the PC’s USB

port and the portable charger’s Micro USB input port (3).

- The LED indicator light (2) will blink during the charging process.

2. All of the LED indicator lights (2) will stay on when charging is

complete. You can now disconnect the USB cable.

LED lights display charging conditions and capacity indications.

For more details, refer to LED conditions on page 4.

!

NOTE

6

ENGLISH

Simultaneous Charging

1. Connect the charger adapter to the USB cable, and plug it into a

wall outlet. Connect the cable to the portable charger’s Micro USB

input port (3).

2. Using a second USB cable (not included), connect the portable

charger’s USB output port (4) to your mobile device’s micro USB port.

3. Whenyourmobiledeviceisnishedcharging,removetheUSBcable

connecting it to the portable charger.

• During simultaneous charging, the charging current will be limited;

therefore, charging may take longer than usual, or charging of the mobile

device may stop. Once the portable charger is fully charged, charging of

your mobile device will begin.

• It is recommended that you use the charger adapter plugged into a wall

outlet during simultaneous charging. Simultaneous charging via USB port

to PC may not charge.

• If the charger adapter is disconnected during simultaneous charging

of the portable charger and a mobile device, the mobile device will be

charged via the portable charger.

!

NOTE

7

ENGLISH

Charging Mobile Devices

To ensure voltage/current compatibility, before charging your mobile device,

check with the manufacturer or manual for the voltage/current charger

specicationsofyourmobiledevice.

!

CAUTION

1. Using the USB cable, connect the portable charger’s USB output

port (4) to your mobile device’s USB port.

2. Press the LED button (1).

- The portable charger’s current battery capacity will be represented

by the LED indicator lights (2).

3. Whenthemobiledeviceisnishedcharging,removetheUSBcable.

• You can use the supplied USB cable to charge your mobile device.

• Available accessories may vary by region, country or service provider.

• Connecting a mobile device that supports Quick Charge™ 3.0 to the

portable charger’s USB output port (4) enables the Quick Charge feature.

!

NOTE

8

ENGLISH

Troubleshooting

Please check the following contents if portable charger does not work.

If the problem is not resolved, please stop use and contact the manufacturer.

Problem Cause & Correction

The portable charger

cannot charge the mobile

device.

• Please check compatibility of the voltage/

currentspecicationbetweentheportable

charger and the mobile device.

• Please check that the cable is connected properly.

• Start charging the mobile device by pressing

the LED button (1) for one second.

The LED indicator doesn’t

ashafterconnecting

the portable charger to

the mobile device.

• After pressing the LED button (1) for one second,

theLEDwillashtoindicatethatthecharging

process has begun.

The LED is not blinking

while the portable

charger is being charged

using a laptop or desktop

computer.

• Please check that the PC is not powered off or

in Sleep mode. If it is, power it on or wake it up.

• The USB port may lack power. Please disconnect

all other devices using USB ports.

There is no LED light

when the LED button (1)

is pressed.

The portable charger is

not charging the mobile

device.

• The portable charger is almost empty.

Please charge it.

• This may happen when short circuit protection

is active. For normal operation, disconnect the

portablechargerwiththecablerstandthen

charge the portable charger again.

9

ENGLISH

Problem Cause & Correction

The charging time is

unusually long.

• The charging time may vary according to the

environmental temperature. Please charge in

5 °C to 35 °C (41 °F to 95 °F).

• The charging time may vary when the portable

charger is connected to PC USB ports

(USBspecication:5V500mA).

• The USB port may lack power. Please disconnect

all other devices using USB ports.

• This may occur when using a USB hub to

charge the portable charger; please directly

connect it to a PC USB port to charge.

The portable charger is

overheating.

• The portable charger may emit heat while

charging or during use; if there is too much

heat or smoke, please stop use.

10

ENGLISH

Problem Cause & Correction

All LED indicator lights

keep blinking fast.

• This may occur due to undesirable environmental

temperatures or if the outlet/port it is plugged

into short circuits.

- The portable charger does not operate

optimally in environments with temperatures

that are too low (below 5 °C [41 °F]) or too

high (above 35 °C [95 °F]).

- The portable charger will not operate optimally

to inputs or outputs with an overcurrent or

overvoltage.

• First disconnect the charger from the portable

charger and then reconnect them.

If that doesn’t work:

• Remove the portable charger from the

undesirable environment or outlet/port. The

unit should now perform correctly.

• If the LED indicator lights keep blinking fast

under normal conditions, please contact the

service centre.

11

ENGLISH

Appendix

Specications

Model PMC-610

Rated input

Max.5V0 2 A

Rated output

5V~6.5V0 3 A,

6.5V~9V0 2 A,

9~12V0 1.5 A Max

Battery capacity

3.63V0 6,500 mAh (Li-Ion)

Battery type Lithium-ion

Charging time Within 4.5 Hrs (Using 2 A charger)

Operating temperature 5 °C to 35 °C

Size (L x W x H) 93 x 60 x 22.5 mm

Weight Approx. 143g

•Depending on the remaining capacity of the portable charger,

the temperature and charging circumstance, the charging time could

be different.

•Designandspecicationsaresubjecttochangewithoutnotice.

12

ENGLISH

Declaration of Conrmation

DECLARATION OF CONFORMITY

Hereby, LG Electronics declares that this PMC-610 is in compliance

with the essential requirements and other relevant provisions of

Directive 2014/30/EU. A copy of the Declaration of Conformity can be

found at http://www.lg.com/global/declaration

Additional Information

Conditions

- The warranty is valid only if the original receipt issued to the original

purchaser by the dealer, specifying the date of purchase and serial

number, is presented with the product to be repaired or replaced.

LG Electronics reserves the right to refuse warranty service if this

information has been removed or changed after the original purchase

of the product from the dealer.

- If LG Electronics repairs or replaces the product, the repaired or

replaced product shall be warranted for the remaining time of the

original warranty period or for ninety (90) days from the date of

13

ENGLISH

repair, whichever is longer. Repair or replacement may involve the

use of functionally equivalent reconditioned units. Replaced parts or

components will become the property of LG Electronics.

- This Warranty does not cover any failure of the product due to normal

wear and tear, or due to misuse, including but not limited to use in

other than the normal and customary manner, in accordance with

instructions for use and maintenance of the product. Nor does this

warrantycoveranyfailureoftheproductduetoaccident,modication

or adjustment, acts of God or damage resulting from liquid.

-

This warranty does not cover product failures due to improper repair,

installations,modicationsorserviceperformedbyanon-LGElectronics

authorized person. Tampering with any of the seals on the product will

void the warranty.

Limited Warranty

SUBJECT TO THE CONDITIONS OF THIS LIMITED WARRANTY,

LG ELECTRONICS WARRANTS THIS PRODUCT TO BE FREE FROM

DEFECTS IN DESIGN, MATERIAL AND WORKMANSHIP AT THE

TIME OF ITS ORIGINAL PURCHASE BY A CONSUMER, AND FOR A

SUBSEQUENT PERIOD OF ONE (1) YEAR. SHOULD YOUR PRODUCT

NEEDWARRANTYSERVICE,PLEASERETURNITTOTHEDEALER

FROM WHOM IT WAS PURCHASED OR CONTACT YOUR LOCAL

LG ELECTRONICS CONTACT CENTER TO GET FURTHER INFORMATION.

14

ENGLISH

Removal of waste batteries and accumulators

(Product with embedded battery ONLY)

- In case this product contains a battery incorporated within the product

which cannot be readily removed by end-users, LG recommends that

onlyqualiedprofessionalsremovethebattery,eitherforreplacement

or for recycling at the end of this product’s working life.

To prevent damage to the product, and for their own safety, users

should not attempt to remove the battery and should contact

LG Service Helpline, or other independent service providers for advice.

- Removal of the battery will involve dismantling of the product case,

disconnection of the electrical cables/contacts, and careful extraction

of the battery cell using specialized tools. If you need the instructions

forqualiedprofessionalsonhowtoremovethebatterysafely,

please visit http://www.lge.com/global/sustainability/environment/

take-back-recycling.

Disposal of waste batteries/accumulators

1 This symbol may be combined with chemical symbols for

mercury (Hg), cadmium (Cd) or lead (Pb) if the battery

containsmorethan0.0005%ofmercury,0.002%of

cadmiumor0.004%oflead.

2 All batteries/accumulators should be disposed separately

from the municipal waste stream via designated

collection facilities appointed by the government or the

local authorities.

3 The correct disposal of your old batteries/accumulators

will help to prevent potential negative consequences for

the environment, animal and human health.

15

ENGLISH

4 For more detailed information about disposal of your old

batteries/accumulators,pleasecontactyourcityofce,

waste disposal service or the shop where you purchased

the product.

Disposal of your old appliance

1 This crossed-out wheeled bin symbol indicates that waste

electrical and electronic products (WEEE) should be

disposed of separately from the municipal waste stream.

2 Old electrical products can contain hazardous substances

so correct disposal of your old appliance will help prevent

potential negative consequences for the environment and

human health. Your old appliance may contain reusable

parts that could be used to repair other products, and

other valuable materials that can be recycled to conserve

limited resources.

3 You can take your appliance either to the shop where you

purchased the product, or contact your local government

wasteofcefordetailsofyournearestauthorisedWEEE

collection point. For the most up to date information for

your country please see www.lg.com/global/recycling

Contact ofce for compliance of this product

LGElectronicsEuropeanSharedServiceCenterB.V.

Krijgsman 1, 1186 DM Amstelveen, The Netherlands

16

ENGLISH

Manufacturer Info

LG ELECTRONICS INC

128, YEOUI-DAERO, YEONGDUNGPO-GU, SEOUL, KOREA

Production Plants

LEUNG’S COMMUNICATION & ELECTRIC PRODUCTS(GUANGZHOU) LTD.

No.39 Nanyunsan Road, Science Park Hi-Tech Industrial Development Zone, Guangzhou,

Gungdong Province, China

Production Date

Production date indicated on the box

Additional information

(1) Storage

Do not install or store the appliance outdoors or in places exposed to direct weather

conditions (direct sunlight, wind, rain or temperatures below zero degrees)

(2) Transportation

The product is transported by any means of transport in accordance with the rules of

transportation of goods, operating in the this type of transportation.

•Transportationmustbecarriedoutunderconditionsexcludingdamage.

•Donotexposetheproducttoimpactloadsduringloadingandunloading.

(3) Realization

•Thesaleofproductsisperformedinaccordancewiththerulesestablishedbythe

current legislation of the country in which it is realized.

(4) Recycling

•Oldelectricalproductscancontainhazardoussubstancessocorrectdisposalofyour

old appliance will help prevent potential negative consequences for the environment

and human health. Your old appliance may contain reusable parts that could be

used to repair other products, and other valuable materials that can be recycled to

conserve limited resources.

•Formoredetailedinformationaboutdisposalofyouroldappliance,pleasecontact

yourcityofce,wastedisposalserviceortheshopwhereyoupurchasedtheproduct.

Page is loading ...

LG PMC-610 User manual

This manual is also suitable for

LG PMC-610 User manual

in other languages

Related papers

Other documents