Craftsman 580.752630 Owner's manual

Brand: Craftsman

Model: 580.752630

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752630

Operator'sIVlanual

3000 PSi MAX*

2.7 GPiViMAX

iViodelNo. 580.752630

HOURS: IVlon.- Fri. 8 a.rn. to 5 p.m. (CTI

WARHIHG

Beforeusing this product, readthis

manualand follow all Safety Rules

and Operatinginstructions.

ADVERTENCiA

Antes de utilizar el producto, lea este

manualy siga todas las Reglasde

Seguridad e Instrucciones de Uso.

,, Safety

,, Assembly

,, Operation

,, Maintenance

,, Parts

,, EspaNol,p. 32

* This pressure washer is rated in accordance to the PressureWasher Manufacturers Association

(PWMA) standard PWI01 (Testing and Rating Performance of Pressure Washers).

* Esta limpiadora a presiOnest_ clasificada conforme a la norma PWl01 (comprobaciOn y clasificaciOn de rendimiento de limpiadoras

a presiOn)de la AsociaciOn defabricantes de bombas a presiOn(Pressure Washer Manufacturers Association, PWMA).

Sears, Roebuckand Co., HoffmanEstates,IL 60179 U.S.A.

Visit our Craftsman website: www.craftsrnan.corn

Part No. 208718GS Draft B(11/04/2009)

WARRANTY .......................................... 2

REPAIRPROTECTIONAGREEMENT........................ 2

SAFETYRULES...................................... 3-5

FEATURESAND CONTROLS.............................. 6

ASSEMBLY........................................ 7-10

OPERATION....................................... 11-15

SPECIFICATIONS..................................... 16

MAINTENANCE.................................... 17-21

STORAGE........................................ 22-23

TROUBLESHOOTING.................................. 24

REPLACEMENTPARTS.............................. 25-28

NOTES............................................. 29

EMISSIONCONTROLWARRANTY..................... 30-31

ESPANOL......................................... 32-55

HOWTO ORDERPARTS........................ BACKPAGE

CRAFTSMANLiMiTEDWARRANTY

If this Craftsmanproduct fails due to a defect in material or workmanship within two years from the date of purchase, return it

to anySearsstore, Sears Parts & RepairService Center,or other Craftsmanoutlet in the United Statesfor free repair (or

replacementif repair proves impossible).

This warranty appliesfor only 90 days from the dateof purchase if this product is ever usedfor commercial or rental

purposes.

Thiswarranty coversOHLYdefectsin material andworkmanship.Searswill HOTpayfor:

* Expendableitems that canwear out from normal usewithin the warranty period, such as spray guns, hoses, nozzle

extensions, nozzles,filters and spark plugs.

. Repairsnecessarybecauseof accident, or failure to operateor maintain the product according to all supplied instructions.

. Preventivemaintenance,or repairs necessarydue to improper fuel mixture, contaminated or stalefuel.

This warranty givesyou specific legal rights, and you may also haveother rights which vary from stateto state.

Sears, Roebuck and Co,, Hoffman Estates, IL 60179

Congratulations on making a smart purchase.

Your new Craftsman® product is designed and manufactured

for years of dependableoperation. But like all products, it

may require repair from time to time. That'swhen havinga

Repair ProtectionAgreement can saveyou money and

aggravation.

Here'swhat the RepairProtection Agreement*includes:

* Expertservice by our 10,000 professional repair

specialists

* Unlimited serviceand no chargefor parts and labor on

all covered repairs

. Product replacementup to $1500 if your covered

product can't befixed

. Discount of 10% from regular priceof serviceand related

installed parts not covered by the agreement;also, 10%

off regular price of preventivemaintenancecheck

* Fasthelp byphone-we caii it Rapid Resolution- phone

support from a Sears representative.Think of us as a

"talking owner's manual".

Onceyou purchasethe RepairProtection Agreement,a

simple phone carlis all it takes for you to schedule service.

You cancall anytimeday or night, or schedule a service

appointment online.

The Repair ProtectionAgreement is a risk-free purchase. If

you cancelfor any reasonduring the product warranty

period,we will provide a full refund. Or, a prorated refund

anytime after the product warranty period expires. Purchase

your RepairProtectionAgreement today!

Some limitations and exclusions apply. Forpricesand

additional informationin the U.S.A. call 1-800-827-6655.

* Coverage in Canadavaries on someitems. Forfuji

details, caii Sears Canadaat 1-800-361-6665.

SearsInstallation Service

ForSearsprofessional installation of home appliances,

garagedoor openers, water heaters,and other major home

items, in the U.S.A.or Canadacall 1-S00-4-MY-HOME®.

Readthis manual carefully and becomefamiliar

with yourpressurewasher. Knowitsapplications,

itslimitations, and any hazardsinvolved.

important Safety I.formation

Safety Symbolsand Meanings

ToxicFumes Kickback

SlipperySurface Fall

ElectricalShock

FluidInjection

Fire

Explosion Operator'sManual

MovingParts Flying Objects Hot Surface

ChemicalBurn

,A Thesafetyalertsymbol indicatesa potential personal

injury hazard.A signalword (DANGER,WARNING,or

CAUTION)is usedwith thealert symbol to designatea degree

or levelof hazardseriousness.A safety symbol may be used

to representthe type of hazard.Thesignal word NOTICEis

usedto addresspractices not relatedto personalinjury.

A. DANGERindicatesa hazardwhich, if not avoided, will

result in deathor serious injury.

A. WARNINGindicates a hazardwhich, if not avoided, could

result in deathor serious injury.

A. CAUTIONindicates a hazardwhich, if not avoided, could

result in minor or moderate injury.

NOTICEaddress practices not relatedto personal injury.

A. WARNING Theengineexhaustfrom this product

contains chemicals known to the Stateof California to

cause cancer,birth defects,or other reproductive harm.

A. WARNING This product contains lead and lead

compounds, known to the State of Californiato cause

birth defects or other reproductive harm. Washyour

handsafter handling this product.

A. WARNING Runningengine gives off carbon

monoxide, an odorless, colorless, poison gas.

_ Breathingcarbon monoxide headache,

can cause

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

Some chemicals or detergentsmay be harmful if inhaled

or ingested, causing severenausea,fainting, or

poisoning.

• OperatepressurewasherONLYoutdoors.

• Keepexhaustgasfromenteringa confinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartor run engineindoorsor in anenclosedarea,

evenifwindowsanddoorsareopen.

• Usea respiratoror maskwheneverthereisa chancethat

vaporsmaybeinhaled.

• Readallinstructionswith masksoyouarecertainthemaskwill

providethenecessaryprotectionagainstinhalingharmful

vapors.

A. WARNING ChemicalBurn Hazard.

Chemicalscould cause bodily injury, property

damageor death.

• DONOTusecausticliquidwith pressurewasher.

• UseONLYpressurewashersafedetergents/soaps.Followall

manufacturersinstructions.

A. WARNING Starter cord kickback(rapid retraction)can

result in bodily injury. Kickbackwill pull hand and

,_arm toward enginefaster thanyou can let go.

Broken bones,fractures, bruises, or sprains

could result.

• NEVERpull starter cord without first relieving spraygun

pressure.

• When starting engine, pull cord slowly until resistance isfelt

andthen pull rapidly to avoid kickback.

• After eachstarting attempt, where enginefails to run, always

point spray gun in safe direction, pressred button andsqueeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

A. WARNING Riskof electrocution.

"_.dh Contactwith power source can causeelectric

shock or burn.

• NEVERspraynearpowersource.

A. WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• DONOTallow CHILDRENto operate pressure washer.

• NEVERrepair high pressure hose.Replaceit.

• NEVERrepair leakingconnections with sealantof any kind.

Replaceo-ring or seal.

• NEVERconnect high pressure hose to nozzleextension.

• Keephigh pressure hose connectedto pump and spraygun

while system is pressurized.

• ALWAYS point spray gun in safedirection, pressred button

andsqueezespray gun trigger to releasehigh pressure, every

time you stop engine.

• NEVERaim spray gun at people,animals, or plants.

• DO NOTsecure spraygun in open position.

• DO NOTleavespray gun unattendedwhile machine is running.

• NEVERuseaspray gun which does not have a trigger lockor

trigger guardin placeand in working order.

• Always be certain spray gun, nozzlesandaccessoriesare

correctly attached.

A. WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHENADDING OR DRAININGFUEL

* Turn pressurewasher OFFand let it cool at least2 minutes

before removing fuel cap. Loosencapslowly to relievepressure

in tank.

, Fillor drain fuel tank outdoors.

, DONOToverfill tank. Allow spacefor fuel expansion.

, Iffuel spills, wait until it evaporatesbeforestarting engine.

, Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

, DONOTlight a cigaretteor smoke.

WHENSTARTINGEQUIPMENT

* Ensurespark plug, muffler,fuel cap,and air cleanerarein place.

* DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIPMENT

, DONOTtip engine or equipment at anglewhich causes fuel to

spill.

, DONOTsprayflammable liquids.

WHENTRANSPORTING,MOVINGOR REPAIRINGEQUIPMENT

, Transport/move/repair with fuel tank EMPTYor with fuel shutoff

valveOFF.

, DONOTtip engine or equipment at anglewhich causes fuel to

spill.

, Disconnectspark plug wire.

WHENSTORINGFUELOR EQUIPMENTWITH FUELIN TANK

* Store awayfrom furnaces, stoves,water heaters,clothes

dryers, or other appliancesthat havepilot light or other ignition

source becausethey can ignitefuel vapors.

A. WARNING Contact with muffler area can result in

serious burns.

_ _ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• It is aviolation of California Public ResourceCode,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other statesor

federaljurisdictions may have similar laws.

Contactthe original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designedfor the exhaust system

installed on this engine.

• Replacement parts must bethe sameand installed in the same

position asthe original parts.

_i, WARNING Use of pressure washer can create

puddles and slippery surfaces.

_' Kickback from spray gun can cause you

to fall.

• Operatepressurewasher from a stablesurface.

• Thecleaning areashould have adequateslopes and drainageto

reducethe possibility of a fall due to slippery surfaces.

• Beextremely careful if you must usethe pressurewasherfrom

a ladder,scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure sprayto avoid injury when spraygun kicks back.

A, WARNING Unintentional sparking can result in fire or

_¢ electric shock.

WHENADJUSTINGOR MAKINGREPAIRSTO YOURPRESSURE

WASHER

• Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGINESPARK

• Use approved spark plug tester.

• DONOTcheckfor sparkwith spark plug removed.

A, WARNING Starter and other rotating parts can

entanglehands, hair, clothing, or accessories.

. NEVERoperatepressurewasherwithoutprotectivehousingor

covers.

. DONOTwearlooseclothing,jewelryor anythingthat maybe

caughtin thestarteror otherrotatingparts.

* Tieuplonghairandremovejewelry.

A, WARNING Riskof eyeinjury.

Spray cansplash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safetyglasses or dry-condition goggles for

indirect vented safetygoggles.

NOTICE High pressure spray may damagefragile items

including glass.

= DONOTpointspraygunatglasswhenusingMAX(0°) nozzle.

= NEVERaimspraygunatplants.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• If you have questions about intended use,ask dealer or contact

Sears.

• NEVERoperate units with broken or missing parts, or without

protective housing or covers.

• DO NOTby-pass any safety device on this machine.

• DONOTtamper with governed speed.

• DONOToperatepressure washer above rated pressure.

• DONOTmodify pressure washer in any way.

• Beforestarting pressure washer in cold weather,check all parts

of the equipment to besure ice has not formed there.

• NEVERmove machine by pulling on hoses. Use handle provided

on unit.

• Checkfuel system for leaksor signs of deterioration, such as

chafed or spongy hose,loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure washer.

• This equipmentis designedto be usedwith Searsauthorized parts

ONLY.If equipment is used with parts that DONOTcomply with

minimum specifications, userassumesall risks and liabilities.

KNOWYOURPRESSUREWASHER

Readthe Operator's Manual and safetyrules before operating yourpressurewasher.

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A- Spray Gun-- Controls the application of water onto cleaning

surface with trigger device. Includestrigger lock.

B- PrecisionSprayTM Nozzles-- Max,General,Flush,Jet Soapand

Detergent Nozzles:for various cleaning applications.

C- AccessoryTray-- Provides convenient storagefor accessories,

such as gun, spray tips, etc.

D - ProjectPro® PerfectlVlixTM Siphon -- Mixes concentrate with

pressure washer spray.

E - Bottle Bracket -- Cleaningsolution bottle fits in wire form

bracket here. Concentratebottle not included.

F - Oil Fill/Dipstick -- Check,add and drain engine oil here.

G - Automatic Cool DownSystem-- Cycleswater through pump

when water reaches 125°-155°F. Warm waterwill dischargefrom

pump onto ground. This system prevents internal pump damage.

H - Pump-- Developshigh pressure.

J - DetergentSiphoningTube/Filter-- Useto siphonpressurewasher

safedetergentsinto thelow pressurestream.

K- HighPressureOutlet -- Connectionfor high pressurehose.

L - Water Inlet-- Connectionfor garden hose.

IVi- Air Filter -- Protects engine byfiltering dust and debris out of

intakeair.

N - Recoil Starter -- Usedfor starting the engine manually.

P- Fuel Tank-- Filltank with regular unleadedfuel. Always leave

room for fuel expansion.

R - Fold Down Handle-- Handleand accessory tray fold fiat atop

cold engine for space-saving storage.

S - NozzleExtensionwith QuickConnect-- Allows you to switch

betweenfive different PrecisionSprayTM nozzles.

T - HoseWrap and High PressureHose-- Hosewrap provides

easytransport and handling of the high pressure hose. Connect

oneend of hoseto water pump andthe other endto spray gun.

items Not Shown:

FuelValve-- Usedto turn fuel supply on and off to engine.

Engine Switch -- Sets engine in starting mode for recoil starter and

stops a running engine.

Choke Rod-- Prepares a cold enginefor starting.

identificationLabel (near rear of base plate) -- Provides model

and serial number of pressure washer. Pleasehave these readily

available if callingfor assistance.

Warning/Operating Instructions Tag-- Identifieshazardsand proper

procedureto start/stop pressurewasher.

Your pressure washer requires some assembly and is ready

for useonly after it has been properly servicedwith the

recommendedoil and fuel.

If you haveany problemswith theassembly of your

pressurewasher, please call the pressurewasher helpline

at 1-800-222-3136.

UNPACKTHEPRESSUREWASHER

1. Removeeverythingfrom carton except pressurewasher,

2. Opencarton completely by cutting eachcorner from top

to bottom.

7. Connectwater supply to pump.

8. Attach nozzleextension to spray gun.

9. Select/attach quick connect PrecisionSprai Mnozzleto

nozzleextension.

Attach Handle and Accessory Tray

1. Placehandle(A) onto handle supports (g) connectedto

main unit. Make sure holes (C) in handlealign with holes

3. Removepressure washer from carton.

CARTONCONTENTS

Checkall contents. If anyparts are missing or damaged,call

the pressure washer helplineat 1-800-222-3136.

* Main Unit

* Handle

* AccessoryTray

* High PressureHose

* Spray Gun

* NozzleExtensionwith Quick ConnectFitting

* Oil Bottle

* HoseWrap

* DetergentSiphoning Hose/Filter

* Bottle BracketWireform (2)

* PerfectMWMSiphoning Unit/Hose

* Parts Bag(which includes the following):

* Operator's Manual

* Owner's Registration Card

* Bag containing 5 PrecisionSprai MNozzles

* HandleFasteningHardwareKit (whichincludes):

* HandleBolts (2)

* CarriageBolt (2)

* Plastic Knobsfor Handle(2)

* Plastic Knob (2)

* TreeClips (4)

Becomefamiliar with eachpiece beforeassemblingthe

pressure washer. Identify all contents with the illustration on

page 6. if any parts are missing or damaged, call the

pressure washer helpline at1-800-222-3136.

NOTICE

hot.

insert handle carriagebolts (D) through holes from

inside of unit and attach a plastic knob (E) from outside

of unit. Tighten by hand. Byloosening both knobs to the

middle section of the attachmentbolt, the upper handle

canfold forward to store fiat atop the cold engine.

DONOTfold the handle down while the engine is

Placeaccessorytray (F) over holes (6) on handle

(viewing from backof unit). Pushthe tree clips (H) into

the holes until they sit fiat against the accessorytray.

ASSEMBLINGPRESSUREWASHER

Your Craftsmanpressure washer will needassembly before

operation:

1. Fill out and sendin registration card.

2. Attach handle and accessorytray.

3. Connectdetergent siphon hoseto pump.

4. Add oil to engine crankcase.

5. Add fuel to fuel tank.

insert multi-colored quick connect nozzlesand other

supplied accessoriesin spacesprovided in accessory

tray. SeeHow to UseAccessory Tray.

6. Connectpressure hose to spray gun and pump.

Align hosewrap (A) to the back side of accessorytray.

Locate notch with "unlock"icon (B) on hose wrap.

Position notch at top with hosewrap in vertical position.

Clips in the back of accessorytray should slide into the

grooves on the inside surface of hosewrap. Slide hose

wrap on back of accessorytray and rotate 1/8 turn until

"locked"icon (6) is in vertical position. Hosewrap is

easily removed from the accessorytray for wrapping and

unwrapping of the high pressure hose. A clip to secure

the hoseon the reel makesit easyto wrap the hose

while it is detachedfrom the accessorytray.

Attach bottle brackets (D) to handle with carriage bolts

(E) and black plastic knobs (F). Tighten by hand.

2-1N-1SoapSystem

The pressure washer is equipped with two detergent

siphoning hoses.

ProjectPro PerfectMixTM Siphon

Bluetube with blue bottle cap:

,._, Whenusing the blue PerfectiViixTMsiphon, use

the PerfectMWMExtremeConcentratestraight

from the bottle.

StandardSiphonTube

Cleartube with filter:

When using the clear siphon tube, dilute

1 part PerfectlViixTMExtremeConcentrate

to 16 parts water (4 ozof concentrate

makes1/2 gallon of mix.)

Attach Project Pro® PerfectMix TM Siphon to

Pump

Attach the hose end of the blue PerfectiVlixTMSiphon (6) to

the barbed hosefitting (I-I)on the pump.

Attach PerfectMix TM Detergent Siphon to

Concentrate BotUe

PlacePerfectMixTMbottle (not included) in the wire-form

bracketon the handle. Removecap from bottle and insert the

PerfectMixTMSiphon (6). Screw the siphon unit to the top of

the bottle (J). Usethe clip on the cap (1{)to snap siphon to

wire form bracketwhen siphon is not in a concentrate bottle.

AddEngineOil

1. Placepressure washer on a flat, levelsurface.

2. Cleanarea around oil fill and remove yellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE Improper treatment of pressure washer can

damage it and shorten its life.

• DO NOTattempt to crank or start the engine beforeit has been

properly servicedwith the recommended oil. This may result in an

enginefailure.

4. Replaceoil fill cap/dipstick and fully tighten.

Add Fuel

A. WARNING Fueland its vapors are extremely

flammable and explosive.

_._ ire or explosion can causesevere burns

or death.

WHEN ADDINGFUEL

• Turn pressure washerOFFand let it cool at least2 minutes

before removing fuel cap. Loosencapslowly to relievepressure

in tank.

• Fill fuel tank outdoors.

• DONOToverfill tank. Allow spacefor fuel expansion.

• If fuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel awayfrom sparks, open flames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigarette or smoke.

1. Useclean, fresh, regular unleadedfuel with a minimum

of 86 octane with equipment. DONOTmix oil with fuel.

2. Placepressurewasher on a levelsurface. Cleanarea

around fuel fill cap, remove cap.

3. Slowly add regular unleadedfuel to bottom of fuel level

limit in neck of fuel tank. Becareful not to overfill.

MA×IMUM FUEL LEVEL

Install fuel cap and allow any spilled fuel to evaporate

beforestarting engine.

CAUTION!Alcohol-blendedfuels (calledgasohol, ethanol or

methanol) canattract moisture, which leadsto separation and

formation of acids during storage.Acidic gascandamagethe

fuel system of an enginewhile in storage.

To avoid engine problems, the fuel system should be emptied

beforestorage of 30 days or longer. Drainthe fuel tank, start

the engineand let it run until the fuel lines and carburetor are

empty. Usefresh fuel next season.See Storagefor additional

information.

NEVERuse engine or carburetor cleaner products in the fuel

tank as permanent damagemay occur.

Connect Hose and Water Supply to Pump

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

= Damagetoequipmentresultingfrom failuretofollowthis

instructionwillvoidwarranty.

4. Runwater through garden hosefor 30 secondsto flush

it of debris. Turn off water.

NOTICE DONOTsiphon standing water for the water

supply. Use ONLYcold water (less than 100°F).

5. Connectgarden hose(not to exceed50 feet in length) to

water inlet. Tighten by hand.

NOTICE Removeand discard the shipping caps from the

pump's high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose and attachone end of hoseto

baseof spray gun. Tighten by hand.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVERconnect high pressure hose to nozzleextension.

• Keephigh pressure hose connectedto pump and spraygun

while system is pressurized.

• Always becertain spray gun, nozzlesandaccessoriesare

correctly attached.

2. Attach other end of high pressure hoseto high pressure

outlet on pump. Tighten by hand.

Beforeconnectinggarden hoseto water inlet, inspect

inlet screen (A). Cleanscreen if it contains debris or have

it replacedif damaged.DONOTrunpressurewasher if

inlet screenis damaged or missing.

NOTICE Using a OneWay Valve (vacuumbreakeror check

valve) at pump inlet can cause pump or inlet connector

damage.

• ThereMUSTbeatleasttenfeetofunrestrictedgardenhose

betweenthepressurewasherinletandanydevice,suchasa

vacuumbreakeror checkvalve.

• Damageto equipment resulting from failure to follow this

instruction will void warranty.

A, WARNING Riskof eyeinjury.

Spray cansplash back or propel objects.

• Always wear indirect vented (chemical splash) safety goggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safetyglasses or dry-condition goggles for

indirect vented safetygoggles.

6. Turn ONthe water, press red button (B) on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

Checklist Before Starting Engine

Reviewthe unit to ensureyou haveperformed all of the

following:

1. Besure to read SafetyRules and Operationsections

before using the pressure washer.

2. Makesure handleis in placeand secure.

3. Checkthat oil has beenadded to proper levelin engine

crankcase.

4. Add proper fuel to fuel tank.

5. Checkfor proper hoseconnections (high pressure and

water supply) and that there are no kinks, cuts, or

damageto the high pressure hose.

6. Provide proper water supply (not to exceed100%).

HOWTOUSEYOURPRESSUREWASHER

If you haveanyproblems operating your pressure washer,

pleasecallthe pressure washer helpline at 1-800-222-3136.

PressureWasherLocation

PressureWasherCJearance

_i, WABNING Exhaustheat/gases can ignite

combustibles, structures or damagefuel tank

causing a fire.

* Keepat least5 ft. (152 cm) clearanceon all sides of pressure

washer including overhead.

Placepressure washer outdoors in an area that will not

accumulate deadlyexhaustgas. DONOTplacepressure

washer where exhaustgas (A) could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensureexhaustgas is kept awayfrom anywindows, doors,

ventilation intakes, or other openingsthat can allow exhaust

gasto collect in aconfined area. Prevailingwinds and air

currents should be taken into considerationwhen positioning

_ressurewasher.

_i, WARNING Runningenginegives off carbon

monoxide,an odorless, colorless, poisonous gas.

_ Breathing cancause headache,

carbon monoxide

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

• OperatepressurewasherONLYoutdoors.

• Keepexhaustgasfromenteringa confinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstartor runengineindoorsor in anenclosedarea,

evenifwindowsanddoorsareopen.

To StartYourPressureWasher

To start your engine-powered pressurewasher for the first

time, follow these instructions step-by-step. This information

alsoapplies wheneveryou start the engine after you havelet

the pressure washer sit idle for at leasta day.

1. Placepressurewasher outside nearan water source

capableof supplying water at a flow rate greaterthan

3.7 gallons per minute and no less than 20 PSi at

pressurewasher end of garden hose.

2. Checkthat high pressure hose is tightly connectedto

spray gun and pump. SeeAssembly for illustrations.

3. Makesure unit is in a levelposition.

4. Connectgarden hoseto water inlet on pressurewasher

pump.

NOTICE DONOTrun the pump without the water supply

connectedand turned on.

• Damageto equipmentresultingfromfailureto followthis

instructionwill voidwarranty.

5. Turn ONthe water, press red button on the gun and

squeezethe trigger to purge the pump system of air and

impurities.

6. Attach nozzleextension to spray gun. Tighten by hand.

ChoosePrecisionSprayTM nozzleyou want to use, pull

backon collar of nozzleextension, insert nozzleand

releasecollar. Tug on nozzleto makesure it is securelyin

place.SeeHow to Use PrecisionSpraSMNozzleSystem.

8. Turn fuel valve (B) to "On" position.

OFF

9. Pullchokerod(A)to"Closed"position.

Closed

NOTICE Fora warm engine, be sure the choke rod (A) is in

the "Open" position.

10. Moveengine stop switch (B) to "On" position.

NOTICE Beforestarting the pressure washer, be sureyou

are wearing safety goggles asdescribed below.

A. WARNING Riskof eyeinjury.

Spraycan splash backor propel objects.

• Always wear indirect vented (chemicalsplash) safety goggles

markedto comply with ANSIZ87.1 when using or in vicinity of

this equipment.

• NEVERsubstitute safetyglasses or dry-condition goggles for

indirect vented safetygoggles.

1. Whenstarting engine, position yourself as

recommendedand grasp starter grip handle and pull

slowly until you feel some resistance.Then pull rapidly

to start engine.

A. WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will puff hand and

_,__ arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVERpull starter cord without first relieving spraygun

pressure.

• When starting engine, pull cord slowly until resistance isfelt

andthen pull rapidlyto avoid kickback.

• After each starting attempt, where enginefails to run, always

point spray gun in safedirection, pressred button and squeeze

spray gun trigger to releasehigh pressure.

• Firmly grasp spray gun with both handswhen using high

pressure sprayto avoid injury when spraygun kicks back.

2. Return recoil starter slowly. DO NOT let rope "snap

back" against starter.

13. When engine starts, slowly move choke rod to "Open"

position as engine warms. If engine falters, move choke

rod to "Closed" position, then to "Open" position.

_i, WARNING The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure, even when engine is

stopped and water is disconnected, which can cause

injury.

• DONOTallow CHILDRENto operatepressure washer.

• Keephigh pressure hose connectedto pump and spraygun

while system is pressurized.

• NEVERaim spraygun at people,animals, or plants.

• DO NOTsecure spray gun in open position.

• DO NOTleavespray gun unattendedwhile machine is running.

• NEVERuse aspray gun which does not have atrigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzlesand accessoriesare

correctly attached.

A. WARNING Contact with muffler area can result in

serious burns.

,_ heat/gases can ignite

Exhaust

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• It isa violation of California Public ResourceCode,Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unlessthe exhaust

system is equippedwith a spark arrester,as defined in Section

4442, maintained ineffective working order. Otherstates or

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer,retailer, or dealer

to obtain a sparkarrester designed for the exhaustsystem

installed onthis engine.

• Replacementparts must bethe same and installed in the same

position as the original parts.

How to Stop Your Pressure Washer

1. Releasespray gun trigger and let engine idle for two

minutes.

2. Move engine stop switch to "Off" position.

3. ALWAYSpoint spray gun in a safe direction, push red

button and squeezespray gun trigger to releaseretained

high water pressure.

flOTICE Spraygun traps high water pressure,evenwhen

engine is stopped and water is disconnected.

_i, WARNING The high pressure stream of water that

this equipment produces cancut through skin

and its underlying tissues, leadingto serious

injury and possible amputation.

Spraygun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

How to Use Accessory Tray

The unit is equipped with an accessorytray with places to

store your spray gun, nozzleextension and quick connect

spray tips. Thereis also a detachable hosewrap at the back

of the accessorytray to hold your high pressure hose.

1. Placenozzleextension in clip on back of accessorytray.

How to Use PrecisionSpray TM Nozzle System

The quick-connect on the nozzJe extension aJJows you to

switch between five different PrecisionSprayTM system

nozzles.PrecisionSprayTM nozzlescan be changedwhile

pressure washer is running oncespray gun trigger lock is

engaged.

Followtheseinstructions to changePrecisionSprayTM

nozzles:

1. Pull back coJJar on quick-connect and puJJ current

PrecisionSprayTM nozzleoff. Store PrecisionSprayTM

nozzlesin holder providedon the accessorytray.

_i, WARNING The highpressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVERexchangePrecisionSprayTM nozzleswithoutthetrigger

lockbeingengagedonthespraygun.

• DONOTtwist PrecisionSprayTM nozzleswhilespraying.

Select desired PrecisionSprayTM nozzle:

* Select orange general PrecisionSprayTM nozzlefor all

purpose cleaning. Cleansvinyl siding, brick patios,

concrete driveways and other surfaces.

GENERAL

Selectred max PrecisionSprayTM nozzlefor maximum

cleaning.Greatfor cleaningstubborn stains,including

grease,tar, wax,and otherhard to removestains.

O MAX

2. Placespray gun through hole on accessorytray on right

side of unit.

3. insert multi-colored PrecisionSprayTM nozzlesin spaces

provided in accessorytray.

4. Wrap high pressure hoseon hosewrap then attach hose

wrap to back of accessorytray.

5. Hook providedon back of accessorytray for safely

storing safety goggles.

Select cyanjet flush PrecisionSprayTM nozzlefor

quick high flow clean up and long reachcleaningof

second story siding and windows.

JET FLUSH

SelectmagentajetsoapPrecisionSprayTM nozzleto

launch soapto second story siding and windows.

JET SOAP

Select black fan soap PrecisionSprayTM nozzlefor

general cleaning. Greatfor applying soap to

vehicles, boats, driveways,decks, and patios.

FAN SOAP

3. Pull backon collar,insert newPrecisionSprayTM nozzle

and releasecollar.Tug on nozzleto makesureit issecurely

in place.

UsageTips

* For most effective cleaning, keep PrecisionSprayTM nozzle

from 8 to 24 inches (20 to 61 cm) awayfrom cleaning

surface.

* If you get PrecisionSprayTM nozzletoo close, especially

using a high pressure nozzle,you may damagesurface

being cleaned.

* DONOTget closer than 6 inches (15 cm) when cleaning

tires.

2-m-I SoapSystem

_i, WARNING Chemical Burn Hazard.

i_ Chemicalscould cause bodily injury, property

damageor death.

• DONOTusecausticliquidwithpressurewasher.

• UseONLYpressurewashersafedetergents/soaps.Followall

manufacturersinstructions.

CleaningandApplyingDetergentwith the

Project Pro® PerfectMixTM Siphon

To apply undiluted detergent using the blue

PerfectMWMsiphon, follow these steps:

1. Reviewuse of PrecisionSprayTM nozzles.

2. Attach PerfectMWMsiphon hoseto pump

and PerfectMWMconcentrate bottle.

NOTICE Contact with the hot muffler can damage detergent

siphoning tube.

• When inserting the siphon into adetergent solution bottle, route

the tube so as to keepit from inadvertently contacting the hot

muffler.

3. Makesure fan soap (black) or jet soap nozzle(magenta)

is installed.

NOTICE Detergentcannot be applied with the high pressure

nozzles(Cyan,Orangeor Red).

4. Makesure garden hoseis connectedto water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

NOTICE You must attach all hoses before you start the

engine.

• Starting the engine without all the hosesconnected and without

the water turned ONwill damagethe pump.

• Damageto equipment resultingfrom failure to follow this

instruction will void warranty.

5. Start engine following instructions How to Start Your

Pressure Washer.

6. Apply detergentto a dry surface, starting at lower

portion of areato be washed and work upward, using

long, even, overlappingstrokes.

7. Allow detergent to "soakin"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surfacefrom drying. DONOTallow detergent to dry on

(prevents streaking).

Cleaningand ApplyingDetergentwith __

the StandardClearSiphon

To apply diluted detergent using the

standard clearsiphon tube, follow these

steps:

1. Reviewuseof PrecisionSprayTM nozzles.

2. Attach clear siphon hoseto barbedfitting on pump.

3. Mix detergent solution as required by job.

4. Placesmall filter end of clear siphoning tube into

container with diluted solution as described above.

NOTICE DONOTinsert standard siphon hose in Extreme

Concentrate.Failureto dilute concentratewill causeexcessive

application and consumption of solution.

NOTICE Makesure the filter is fully submerged in fluid

while applying solution.

NOTICE Contact with the hot muffler can damage detergent

siphoning tube.

• When inserting the siphon into adetergent solution bottle, route

the tube so as to keepit from inadvertently contacting the hot

muffler.

5. Makesure fan soap (black) or jet soap nozzle(magenta)

is installed.

NOTICE Detergentcannot be applied with the high pressure

nozzles(Cyan,Orangeor Red).

6. Make sure garden hose is connectedto water inlet.

Checkthat high pressure hoseis connected to spray gun

and pump. Turn on water.

NOTICE You must attachall hoses before you start the 2.

engine.

* Startingtheenginewithoutallthehosesconnectedandwithout 3.

thewaterturnedONwill damagethepump.

, Damageto equipmentresultingfromfailuretofollowthis 4.

instructionwill voidwarranty. 5.

Start enginefollowing instructions How to Start Your

Pressure Washer.

Apply detergent to a dry surface, starting at lower

portion of areato be washedand work upward, using

long, even,overlapping strokes.

9. Allow detergent to "soak in"for 3-5 minutes before

washing and rinsing. Reapplyas neededto prevent

surfacefrom drying. DONOTallow detergentto dry on

(prevents streaking).

NOTICE You must flush the detergent siphoning system

after each use by placingthe filter into a bucket of clean

water, then run the pressure washer in low pressure for 1-2

minutes.

Pressure Washer Rinsing

ForRinsing:

1. Removesoap PrecisionSprayTM nozzlefrom nozzle

extension.

2. Selectand install desiredhigh pressure nozzlefollowing

instructions How to UsePrecisionSprayMNozzleSystem.

3. Keepspray gun a safedistance from areayou plan to

spray.

_i, WARNING Kickbackfrom spray gun cancauseyou to

fall.

• Operatepressurewasherfrom astablesurface.

= Beextremelycarefulif youmustusethepressurewasherfrom

a ladder,scaffolding,oranyothersimilarlocation.

= Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidinjurywhenspraygunkicksback.

4. Apply a high pressure spray to a small area and then

checksurface for damage, if no damageis found, you

can assumeit is okay to continue rinsing.

5. Start attop of areato be rinsed, working down with

same overlapping strokes asyou used for cleaning.

Cleanin9 Detergent Siphonin9 Tube

If you usedthe cleardetergent siphoning tube, you must

flush itwith cleanwater beforestopping the engine,

1. Placedetergent siphoning tube/filter ina bucketfull of

cleanwater.

Removehigh pressure nozzlefrom nozzleextension.

Select and install a soap nozzlefollowing instructions

How to Use PrecisionSprayTMNozzleSystem.

Flushfor 1-2 minutes.

Shut off engine following instructions How to Stop

Pressure Washerand turn off water supply.

6. ALWAYSpoint spray gun in a safe direction push red

button and squeezespray gun trigger to releaseretained

high water pressure.

NOTICE Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected.

_i, WARNING The highpressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

AutomaticCoolDownSystem(Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reachtemperatures above

125°F.The systemengagesto cool the pump by discharging

the warm water onto the ground.

Pressure Washer Specifications

Max Outlet Pressure ...................... 3,000 PSI*

Max Flow Rate............................. 2.7 GPM

DetergentMix ........................ Useas directed

Water Supply Temperature.......... Not to exceedIO0°F

Engine Specifications

Bore ............................... 2.7 in. (69 mm)

Stroke ............................. 2.0 in. (50 ram)

Displacement .................... 11.4 cu. in. (187 cc)

Spark Plug

Resistor ............................ NGKBPR6ES

Set GapTo: ........... 0.028-0.031 in (0.70-0.80 mm)

IntakeValve Clearance ........... 0.15 + 0.04 mm (cold)

ExhaustValveClearance.......... 0.20 + 0.04 mm (cold)

FuelCapacity .................... 0.25 Gallons(0.93 I)

Oil Capacity ...................... 18.56 ft. oz. (0.55 I)

* This pressure washer is rated in accordanceto the

PressureWasher Manufacturers Association (PWMA)

standard PWI01 (Testing and Rating Performanceof

PressureWashers).

OWHER'SRESPOHSIBILITIES

Follow the hourly or calendarinteHals,whichever occurs

first. More frequent service is required when operating in

adverseconditions noted below.

* Changeengineoil

* Check/clean waterinlet screen'

Checkhigh pressure hose

Checkdetergent siphoning hose

Checkspray gun and assembly for leaks

Cleandebris

Checkengine oil level

Cleanengine air cleaner2

Changeengine oiF

Check/adjustspark plug

Inspect muffler and spark arrester

Check/adjustidle speeds

Check/adjustvalve clearances

* Cleanfuel tank & filters

* Cleancombustion chambers

* Replaceengineair cleaner

* Replacespark plug

Checkfuel tubes(Replaceif necessary)

' Clean if clogged. Replace if perforated or torn.

2Service more often under dirty or dusty conditions.

sThese items should be serviced by your servicing dealer.

GeneralBecommendaUons

Regularmaintenancewill improve the performanceand

extend the life of the pressure washer. Seeany Searsor

other qualified servicedealer for service.

The pressurewasher warranty does not cover items that

havebeensubjectedto operator abuseor negligence. To

receivefull valuefrom the warranty, the operator must

maintain pressure washer as instructed in this manual

including proper storage as detailedin Storage.

Some adjustments will needto be madeperiodically to

properly maintain your pressure washer.

All service and adjustments should be madeat least once

each season.Follow the requirements in the Maintenance

Schedulechart above.

NOTICE Oncea yearyou should cleanor replacethe spark

plug and replacethe air filter. A newspark plug and cleanair

filter assure proper fuel-air mixture and help your engine run

better and last longer.

Pump Oil

DONOTattempt anyoil maintenanceon this pump. The

pump is pre-iubricated and sealedfrom the factory, requiring

no additional maintenancefor the life of the pump.

Emissions Control

Maintenance, replacement,or repair of the emissions

controldevices and systemsmay be performedbyany non-

roadengine repair establishment or individual. However,

to obtain "no charge" emissions control service, the work

must be performed by a factory authorizeddealer. Seethe

Emissions Warranty.

Before Each Use

1. Checkengine oil level.

2. Cleandebris.

3. Checkwater inlet screenfor damage.

4. Checkhigh pressure hose for leaks.

5. Checkgun and nozzleextension assemblyfor leaks.

6. Purge pump of air and contaminants.

PRESSUREWASHERMAINTENANCE

CleanDebris

Daily or beforeuse, cleanaccumulated debris from pressure

washer. Keeplinkage, spring and controls clean. Keeparea

around and behind muffler free from anycombustible debris.

Inspect cooling air slots and openings on the pressure

washer.These openings must be kept cleanand

unobstructed.

Pressurewasher parts should be kept clean to reducethe

risk of overheating and ignition of accumulated debris.

* Usea damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of pressurewasher can

damageit and shorten its life.

• DONOTinsertanyobjectsthroughcoolingslots.

A WAFtNIN(_ The high pressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

Spray gun traps high water pressure,evenwhen engine is

stopped and water is disconnected, which can cause

injury.

• Keephighpressurehoseconnectedto pumpandspraygun

whilesystemispressurized.

• ALWAYSpointspraygunin safedirection,pressredbutton

andsqueezesprayguntriggerto releasehighpressure,every

timeyoustopengine.

3. Removenozzlefrom end of nozzleextension.

4. Usea small paperclip to free any foreign material

clogging or restricting nozzle (A).

* Usea soft bristle brush to loosen cakedon dirt, oil, etc.

* Usea vacuum cleanerto pick up loose dirt and debris.

CheckandCleaninlet Screen

Examinegarden hose inlet screen. Cleanif it is clogged or

replaceif it is torn.

Check High Pressure Hose

High pressure hosescan developleaks from wear, kinking,

or abuse, inspect hosebefore eachuse. Checkfor cuts,

leaks,abrasions, bulging of cover,or damageor movement

of couplings. If any of these conditions exist, replacehose

immediately.

A WARNING The high pressure stream of water that

this equipment produces cancut through skin

and its underlying tissues, leadingto serious

injury and possible amputation.

• NEVERrepairhighpressurehose.Replaceit.

• ReplacementhoseratingMUSTexceedmaximumpressure

ratingof unit.

Check Gun and Nozzle Extension

Examinehoseconnectionto spraygun and makesureit is

secure.Testtrigger bypressingit and makingsureit springs

backintoplacewhenyou releaseit. Donotdepressredbutton

andtesttrigger.Youshouldnot beableto presstrigger. Replace

spraygun immediatelyif it fails anyof thesetests.

NozzleMaintenance

A pulsing sensationfelt while squeezingthe spray gun trigger

may be causedby excessivepump pressure.Theprincipal

causeof excessivepump pressure is a nozzleclogged or

restricted with foreign materials, such asdirt, etc. To correct

the problem, immediately cleanthe nozzlefollowing these

instructions:

1. Shut off engine and turn off water supply.

2. ALWAYSpoint spray gun in a safe direction, press red

button and and squeezespray gun trigger to release

retainedhigh water pressure.

5. Removenozzleextensionfrom spray gun.

6. Using a garden hose, removeadditional debris by back

flushing water through nozzleextension. Backflush

between30 to 60 seconds.

7. Reinstallnozzleintonozzleextension.

8. Reconnectnozzleextension to spray gun.

9. Makesure garden hose is connected to water inlet.

Checkthat high pressure hose is connectedto spray gun

and pump. Turn on water.

10. Start engine following instructions How to Start Your

Pressure Washer.

11. Test pressure washer byoperating with eachquick

connect nozzle.

O-Ring Maintenance

Purchasean O-Ring RepairKit, item 7175116, atyour local

Searsor by calling 1-800-4-MY-NOME(469-4663) or online

atwww.sears.com. It is not includedwith the pressure

washer. This kit includes replacemento-rings and a water

inlet filter. Refer to the instruction sheet provided in the kit to

serviceyour unit's o-rings.

A WARNING The highpressure stream of water that

this equipment produces can cut through skin

and its underlying tissues, leading to serious

injury and possible amputation.

• NEVERrepairleakingconnectionswithsealantofanykind.

Replaceo-ringor seal.

ENGINEMAINTENANCE

A WARNING Unintentionalsparking can result in fire or

_i_ electric shock.

WHENADJUSTINGORMAKINGREPAIRSTOYOURPRESSURE

WASHER

• Disconnectthesparkplugwirefromthesparkplugandplace

thewirewhereit cannotcontactsparkplug.

WHENTESTINGFORENGINESPARK

• Useapprovedsparkplugtester.

• DONOTcheckfor sparkwith sparkplugremoved.

Oil

Oil Recommendations

NOTICE Whenadding oil to the enginecrankcase,use only

high quality 4-stroke automotive detergent oil ratedwith APi

serviceclassification SJ or SL ratedSAE10W-30 weight. DO

NOTusespecial additives.

1. Choosea viscosity according to table below.

-20 0 20 40 60 80 1O0°F

-30 -20 -10 0 10 20 30 40°C

AMBIENT TEMPERATURE

NOT/CE Otherviscosities shown in the chart may be used

when the averagetemperature in your area is within the

recommended range.

CheckingOil Level

Oil level should be checked prior to eachuseor at least every

8 hours of operation. Keepoil levelmaintained.

1. Placepressure washer on a levelsurface and cleanarea

around oil dipstick.

2. Removeoil dipstick and wipe dipstick with clean cloth.

insert and remove dipstick without screwing it into the

filler neck.

3. Verify oil is at upper limit mark on dipstick. Replaceand

tighten dipstick.

OiL FILLER CAP/DiPSTiCK

UPPER

_ _9_==.=LiMiT

_IF==.=LOWER

LiMiT

AddEngineOil

1. Placepressurewasher on a fiat, levelsurface.

2. Cleanareaaround oil fill and remove oil fill cap/dipstick.

3. Checkoil levelasdescribed in CheckingOilLeveL

4. If needed,slowly pour oil into oil fiii opening. Pauseto

permit oil to settle. Fillto upper limit mark on dipstick.

DONOToverfill.

NOT/CE Overfilling with oil may cause the engine to not

start, or hard starting.

• DONOToverfill.

• If over the FULLmark on dipstick, drain oil to reduce oil levelto

FULLmark on dipstick.

5. Replaceoil fill cap/dipstick and fully tighten.

ChangingEngineOil

if you are using your pressure washer under extremely dirty

or dusty conditions, or in extremely hot weather,changeoil

more often.

A CAUTION Avoid prolonged or repeatedskin contact

with usedmotor oil.

• Usedmotoroil hasbeenshownto causeskincancerin certain

laboratoryanimals.

• Thoroughlywashexposedareaswithsoapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOILTOCOLLECTIONCENTERS.

Changeoil while engine isstill warmfrom running,as

follows:

1. Drainfuel tank by running pressurewasher until fuel

tank is empty.

2. Disconnectspark plug wire and keepit awayfrom spark

plug.

3. Cleanareaaround oil fill, remove oil fiii cap/dipstick.

Wipe dipstick clean.

4. Tip your pressure washer toward the oil fill neckto drain

oil into a suitable container. Whencrankcase is empty,

return pressure washer to upright position.

5. Slowly pour recommendedoil (approximately 18 oz.)

into oil fill opening. Pauseto permit oil to settle. Fill to

upper limit mark on dipstick.

6. Replaceand tighten dipstick.

7. Wipe up any remaining oil.

8. Reconnectspark plug wire to spark plug.

ServiceAir Cleaner

Your enginewill not run properly and may be damaged ifyou

run it with a dirty air cleaner.Service more often if operating

under dirty or dusty conditions. Replacementsare available

at your local Searsservicecenter.

Toservice the air cleaner, foJlowthesesteps:

1. Press latch tabs (A) on top of air cleanercover (B), and

remove cover.

2. Carefully removeair cleaner(C) from base(D).

3. Cleanair cleanerby tapping it severaltimes on a hard

surfaceto removedirt, or blow compressed air (not to

exceed30 psi) through air cleanerfrom cleanside that

facesengine.

NOTICE NEVERtry to brush off dirt. Brushing will force dirt

into thefibers.

4. Wipe dirt from air cleanerbody and cover using a moist

rag. Be careful to prevent dirt from enteringair duct (E)

that leadsto the carburetor.

5. Install clean(or new)air cleaner in base. Air cleaner

must fit securely in base.

6. Reinstall air cleanercover.

NOTICE You can purchase new air filter elementsby calling

1-888-4-1VlY-HOIVlE(489-4883).

Service Spark Plug

Changingthe spark plug will helpyour engine to start easier

and run better.

1. Disconnectthe capfrom the spark plug and clean area

around spark plug.

2. Removeand inspect spark plug.

3. Replacespark plug if electrodesare worn, or if insulator

is cracked or chipped.

4. For replacement,use recommendedspark plug, NGK

BPR6ES.

5. Checkelectrode gap with wire feelergauge and set gap

at 0.028-0.031 inches 0.70-0.80 mm), if necessary.

6A. When reinstalling original spark plug, tighten 1/8-1/4

turn after the spark plug seatsto compress the washer.

6B. When installing newspark plug, tighten 1/2 turn after

the spark plug seatsto compress the washer.

7. Attach the spark plug capto the spark plug.

NOTICE You can purchasea new spark plug by calling

1-8O8-4-1VlY-HOIVlE(489-4883).

Carburetor

If you think your carburetor needsadjusting, seeyour

nearestSearsservice center. Engineperformance may be

affected ataltitudes above 5000 feet. Foroperation at higher

elevations,contact your nearestSearsservice center.

inspect Muffler and Spark Arrester

inspect the muffler for cracks,corrosion, or other damage.

Removethe spark arrester, if equipped,and inspectfor

damageor carbon blockage,if replacementparts are required,

makesure to use only original equipment replacementparts.

_i, WARNING Contact with muffler area can result in

serious burns.

_ Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipment to cool beforetouching.

• Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• it isa violation of California Public ResourceCode, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unlessthe exhaust

system is equippedwith a spark arrester,as defined in Section

4442, maintained ineffective working order. Otherstates or

federaljurisdictions may havesimilar laws.

Contactthe original equipment manufacturer,retailer, or dealer

to obtain a sparkarrester designed for the exhaustsystem

installed onthis engine.

• Replacementparts must bethe same and installed in the same

position as the original parts.

Page is loading ...

Craftsman 580.752630 Owner's manual

Brand: Craftsman

Model: 580.752630

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

580752630

Download PDF

report

in other languages

español: Craftsman 580.752630 El manual del propietario

Craftsman 580.752630 Owner's manual

This manual is also suitable for

Craftsman 580.752630 Owner's manual

in other languages

Related papers

Other documents