Rothenberger Wet drilling machine RODIADRILL Ceramic User manual

RODIADRILL Ceramic

RODIADRILL Ceramic ECO

RODIADRILL Ceramic

RODIADRILL Ceramic ECO

www.rothenberger.com

DE Bedienungsanleitung

EN Instructions for use

FR Instruction d’utilisation

ES Instrucciones de uso

IT Istruzioni d’uso

NL Gebruiksaanwijzing

PT Instruções de serviço

DA Brugsanvisning

SV Bruksanvisning

NO Bruksanvisning

FI Käyttöohje

PL Instrukcja obslugi

CZ Návodkpoužívání

TR Kullanim kilavuzu

HU Kezelési útmutató

EL Οδηγίεςχρήσεως

RU Инструкцияпоиспользованию

Overview

B Operating

A

1 2

RODIADRILL Ceramic ECORODIADRILL Ceramic

OPTIONAL:

FF30150

FF30250

RODIADRILL Ceramic ECO

RODIADRILL Ceramic

max. Ø 40 x 400 mm

max. Ø 35 x 150 mm

Ø 6 - 67 mm

1

7

16

12

FF40140 Typ C, FF40140Z Typ J

FF40150 Typ C, FF40150Z Typ J

8

3

2

1

6

5

4

2

3

7

8

12

9

10

11

13

14

15

1

2

OPTIONAL:

FF35301

¦

Page is loading ...

10 ENGLISH

Contents

Page

1 Safety Notes ........................................................................................................................ 11

1.1 Intended use..................................................................................................................... 11

1.2 General Power Tool Safety Warnings ............................................................................... 11

1.3 Special Safety Instructions ............................................................................................... 12

2 Technical Data .................................................................................................................... 13

3 Electric supply .................................................................................................................... 13

3.1 Putting the PRCD switch into operation ............................................................................ 13

4 Function of the Unit ............................................................................................................ 14

4.1 Overview (A) ..................................................................................................................... 14

4.2 Start of operation .............................................................................................................. 14

4.3 Handling ........................................................................................................................... 15

5 Care and Maintenance ........................................................................................................ 16

6 Accessories......................................................................................................................... 16

7 Customer service ................................................................................................................ 16

8 Disposal ............................................................................................................................... 16

Markings in this document:

Danger!

This sign warns against the danger of personal injuries.

Caution!

This sign warns against the danger of property damage and damage to the envi-

ronment.

Call for action

ENGLISH 11

1 Safety Notes

1.1 Intended use

The diamond wet drilling machine RODIADRILL Ceramic + ECO is suitable for manual drilling of

holes of up to Ø 67 mm in diameter and when using a RODIACUT drill stand. A ROTHEN-

BERGER centering aid can be used as an optional accessory. The drill holes that are created

have smooth walls. The valid regulations are to be observed for plugging. Persons under the

age of 16 are not to use the equipment.

1.2 General Power Tool Safety Warnings

WARNING!

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious in-

jury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or bat-

tery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will in-

crease the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current de-

vice (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, al-

cohol or medication. A moment of in attention while operating power tools may result in se-

rious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropri-

ate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connect-

ing to power source and/or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energising power tools that have the switch on

invites accidents.

12 ENGLISH

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of these devices can reduce dust re-

lated hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The cor-

rect power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamil-

iar with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tools operation. If dam-

aged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these instruc-

tions, taking into account the working conditions and the work to be performed. Use

of the power tool for operations different from those intended could result in a hazardous sit-

uation.

5) Service

Have your power tool serviced by a qualified repair person using only identical re-

placement parts. This will ensure that the safety of the power tool is maintained.

1.3 Special Safety Instructions

Please wear hearing protection. Exposure to noise can lead to loss of hearing.

Power sockets in outside areas must be fitted with residual current circuit-breakers. This is an

installation regulation requirement for your electric system. Please be sure to observe this when

using the equipment.

Always wear protective goggles when working with the equipment. We recommend protective

gloves, sturdy, non-slip shoes and an apron.

Shavings or chips must not be removed when the equipment is running.

Dust that arises during work is often harmful to health and should not be allowed to enter the

body. Please wear a suitable dust protection mask.

Please remove the plug from the electric socket before all work on the equipment.

Be sure the equipment is switched off before connecting it to the electric socket.

Always keep the connecting cable away from the sphere of action of the equipment. Always

guide the cable away from the equipment to the rear.

Please look out for electric cables, gas and water pipes when working on the wall, ceiling or

floor.

Protect the equipment against splash water. Do not work over head!

ENGLISH 13

2 Technical Data

Nominal acceptance power .........

800 W

1. Gear

2. Gear

Speed .........................................

3600 min-1 ............

6400 min-1

Drilling diameter ..........................

Ø 25 – 67 mm .......

Ø 6 – 25 mm

Drilling range ..............................

Masonry Ø 40 x 400 mm

Concrete Ø 35 x 150 mm

Tile Ø 6 – 67 mm

Tool fitting ...................................

Quick change adapter with G 1/2" fitting

Weight ........................................

approx. 3,4 kg; Ceramic ECO approx.3,2 kg

Drill bit types ...............................

High Speed Plus, No. FF44806 – FF44868

SPEED STAR DX, No. FF00610 – FF00665

Noise pressure level (L

pA

) ...........

91 dB (A) ¦ K

pA

3 dB (A)

Sound power level (L

WA

) .............

102 dB (A) ¦ K

WA

3 dB (A)

The noise level during operation can exceed 85 dB (A). Wear hearing protection!

Measured values determined in accordance with EN 60745-1.

Vibration total value .............................................................

2,6 m/s

2

¦ K= 1,5m/s

2

The vibration level given in this information sheet has been measured in accordance with a

standardised test given in EN 60745 and may be used to compare one tool with another. It may

be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool.

However if the tool is used for different applications, with different accessories or

insertion tools or is poorly maintained, the vibration emission may differ. This may

significantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the

times when the tool is switched off or when it is running but not actually doing the

job. This may significantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibra-

tion such as: maintain the tool and the accessories, keep the hands warm, organisa-

tion of work patterns.

3 Electric supply

Only connect to one-phase alternating current and to the mains voltage indicated on the power

rating plate.

3.1 Putting the PRCD switch into operation

Only suitable for AC current! Note the mains network voltage!

Perform the following test procedure on the PRCD switch before every putting into operation of

the device:

1. Connect the PRCD plug connector with the socket.

2. Press on RESET. The indicator switches to ORANGE (ON).

3. Pull the plug connector out of the socket. The display switches itself off.

4. Repeat 1. and 2.

5. Press on TEST. The orange indicator switches itself off.

6. Press on RESET to switch the device on (ORANGE).

14 ENGLISH

These protective device protect against faults in the attached device, not against such

faults in the preceding plant.

4 Function of the Unit

4.1 Overview (A)

1

Diamond wet bore crown

9

Water tank

2

Quick change adapter

10

Cap nut

3

Sliding sleeve

11

Pump

4

Quantity control valve

12

Hand grip

5

Control valve

13

Control display

6

Sealing plug for external water connection

14

ON/RESET button

7

Gear change

15

OFF/TEST button

8

Switch with regulating electronics

16

Clamping adaptor

4.2 Start of operation

The diamond wet drill must only be operated with a residual current device

(PRCD) (Switzerland FI switch). The residual current device (PRCD) (Switzer-

land FI switch) is compulsory for wet operation, as there is otherwise danger

to life!

Quick change adapter fitting for diamond wet bore crowns (ill. B-1)

G 1/2" connecting thread for the wet bore crown.

 Screw the bore crown (1) (SW24 open-ended spanner) into the quick change adapter (2)

(SW27 open-ended spanner) before using for the first time.

Always keep the quick change adapter clean!

Changing the drill bit

Please wear protective gloves when changing the drill bit. The drill can become

hot after being in use for a longer period of time!

 Push back the sliding sleeve (3) on the output shaft and remove the quick change adapter to

the front together with the screwed on bore crown.

 Replace by another bore crown with fitted quick change adapter.

 To fit a bore crown push back the sliding sleeve and insert the quick change adapter in the

correct position.

Please check that it is lock-fitted!

Please note: Ensure that the quick change adapter is only inserted into the output shaft in a

clean condition.

Water supply RODIADRILL Ceramic

Water is supplied from the water tank (9) during drilling. The water tank can be opened for filling

with water by turning the cap nut (10).

 Fill the water into the pressure tank carefully.

 The maximum filling quantity should not exceed 0.75 litres, see marking on the water tank

(9).

Water must not run over the equipment. Use a funnel if necessary. Only fill with

clean water (tap water)!

The pressure necessary for the water supply is generated by the piston pump (11).

ENGLISH 15

 Pumping up of the pressure tank: approx. 10 pump strokes.

 Set the water quantity using the valve (4), position 1 means a small amount of water and

position 2 plenty of water.

 Operate the water flow to the bore crown and borehole location manually using the control

valve (5).

Optional: External water supply

 Set the valve (4) to "0" to shut down the water supply from the water tank.

 Remove the sealing plug (6) and connect the water hose (optional, No. FF35301).

Attention! Check the seal on the water hose connection!

Water supply RODIADRILL Ceramic ECO

The water supply is by means of a quick plug-in coupling, as an option with a No. FF35026 wa-

ter pressure tank or No. FF35302 water connecting hose on Gardena.

4.3 Handling

 Set the suitable speed using the gear change (7) rotary switch (s. technical data).

 Hold the equipment firmly by the hand grip (12). Use the other hand to guide the neck at the

front of the equipment under the valve block.

Be sure without fail to take up a firm position. Do not stand on ladders or

other moving items!

 Use the switch (8) to switch on the equipment (with "acceleration" function) and accelerate

immediately to maximum speed.

 Apply the bore crown and start drilling using consistent pressure. Use of the optional No.

FF35750 spot drill aid is recommended at the face of the borehole.

 RODIADRILL Ceramic: Briefly operate the water supply valve.

RODIADRILL Ceramic ECO: Turn on the water connection.

 Continue drilling using slight follow-up pressure and in the process consistently impulse-

press the water supply valve.

Attention! No dust formation should be visible!

 Relieve the crown at intervals and retract slightly (oscillating movement) in order to flush out

the drilling mud.

Use continuous flushing when changing over from drilling tiles or natural stone to drilling the

subjacent carrier stone in order to keep the drill as free from drilling mud as possible.

Notes on achieving optimum drill results

 A continuous water supply to the drill bit is preferred in order to keep drilling cores and drill-

ing core scraps from collecting.

In case the bore crown is blocked by drilling core remains all the same or the water flow rate is

impaired by drilling mud, the borehole must be pierced in the crown with the assistance of a

suitable aid (drilling core pusher or suitable wire).

 Immediately remove any possible drilling cores and drilling core remains from the bore

crown each time after drilling before this becomes caked together.

 Only use clean water (tap water) to fill the pressure tank.

Attention! Relieve the tank pressure first!

 Only use diamond drill bits that have been tested by ROTHENBERGER.

To some extent, commercially available diamond bore crowns from third-party manufacturers

feature excessive true-running inaccuracy. Problems arise for this reason when starting up on

damageable surfaces and in addition to these precision boreholes are not possible.

16 ENGLISH

5 Care and Maintenance

Clean carefully after drilling has been finished and blow out using compressed air. Lightly lubri-

cate screws and thread.

Flushing head: drain off water, blow out and oil the thread lightly.

Remove all water and grease from the hand grip.

Important! All maintenance, overhauling and repair work must only be carried out by trained

specialised staff.

6 Accessories

Accessory Name

ROTHENBERGER Part Number

Transport case RODIADRILL Ceramic

FF60140

Transport case RODIADRILL Ceramic ECO

FF60150

Quick change adaptor G 1/2"

FF35751

Freehand drill support up to Ø 83 mm

FF35750

Freehand drill support up to Ø 43 mm

FF35749

Water collect. ring, hand-opd. (up to Ø 130 mm)

FF35701

Spare water collection ring discs (for FF35701)

FF35702

Special water supply hose

FF35301

Water supply hose with “aqua-stop”

FF35302

Pressurized water container 10 l

FF35026

Drill stand RODIACUT 150

FF30150

Drill stand RODIACUT 250

FF30250

7 Customer service

The ROTHENBERGER service locations are available to help you (see listing in catalog or on-

line) and replacement parts and service are also available through these same service locations.

Order your accessories and spare parts from your specialist retailer or using RoService+ online:

Phone: + 49 (0) 61 95 / 800 – 8200

Fax: + 49 (0) 61 95 / 800 – 7491

Email: service@rothenberger.com

www.rothenberger.com

8 Disposal

Components of the unit are recyclable material and should be put to recycling. For this purpose

registered and certified recycling companies are available. For an environmental friendly dispos-

al of the non-recyclable parts (e.g. electronic waste) please contact your local waste disposal

authority.

For EU countries only:

Do not dispose electric tools with domestic waste. In accordance with the European

Directive 2012/19/EU the disposal of electrical and electronic equipment and its im-

plementation as national law, electric tools that are no longer serviceable must be

collected separately and utilised for environmentally compatible recycling.

Page is loading ...

EU-KONFORMITÄTSERKLÄRUNG

Wir erklären in alleiniger Verantwortung, dass dieses

Produkt mit den angegebenen Normen und Richtlinien

übereinstimmt.

EU-DECLARATION OF CONFORMITY

We declare on our sole accountability that this product

conforms to the standards and guidelines stated.

DECLARATION EU DE CONFORMITÉ

Nous déclarons sous notre propre responsabilité que ce

produit est conforme aux normes et directives indiquées.

DECLARACION DE CONFORMIDAD EU

Declaramos, bajo nuestra responsabilidad exclusiva, que

este producto cumple con las normas y directivas

mencionadas.

DICHARAZIONE DI CONFORMITÀ EU

Dichiariamo su nostra unica responsabilità, che questo

prodotto è conforme alle norme ed alle direttive indicate.

EU-KONFORMITEITSVERKLARING

Wij verklaren in eigen verantwoordelijkheid dat dit

product overeenstemt met de van toepassing zijnde

normen en richtlijnen.

DECLARAÇÃO DE CONFORMIDADE EU

Declaramos, sob responsabilidade exclusiva, que o

presente produto está conforme com as Normas e

Directivas indicadas.

EU-KONFORMITETSERKLÆRING

Vi erklærer som eneansvarlig, at dette produkt er i

overensstemmelse med anførte standarder,

retningslinjer og direktiver.

EU-FÖRSÄKRAN

Vi försäkrar på eget ansvar att denna produkt uppfyller

de angivna normerna och riktlinjerna.

EU-SAMSVARSERKLÆRING

Vi erklærer på eget ansvar at dette produktet stemmer

overens med de følgende normer eller normative

dokumenter.

TODISTUS EU-STANDARDINMUKAISUUDESTA

Todistamme täten ja vastaamme yksin siitä, että tämä

tuote on allalueteltujen standardien ja

standardomisasiakirjojen vaatimusten mukainen.

DEKLARACJA ZGODNOŚCI EU

Oświadczamy z pełną odpowiedzialnością, że produkt

ten odpowiada wymaganiom następujących norm i

dokumentów normatywnych.

EU-PROHLÁŠENÍ O SHODÌ

Se vší zodpovìdností prohlašujeme, že tento výrobek

odpovídá následujícím normám a normativním

dokumentům.

EU UYGUNLUK BEYANI

Tek sorumlu olarak bu ürünün yönetmelik hükümleri

uyarýnca aþaðýdaki normlara ve norm dokümanlarýna

uygunluðunu beyan ederiz.

EU-AZONOSSÁGI NYILATKOZAT

Teljes felelősségünk tudatában kijelentjük, hogy jelen

termék megfelel a következő szabványoknak vagy

szabványossági dokumentumoknak.

ΔΗΛΩΣΗ ΠΙΣΤΟΤΗΤΑΣ ΕU

Δήλώνουμε με αποκλειστική μας ευθύvη, ότι αυτό το

προϊόv αvταποκρίvεται στα ακόλουθα πρότυπα ή

έγγραφα τυποποίησης.

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ СТАНДАРТАМ

EU.

Мы заявляем что этот продукт соответствует

следующим стандартам.

RODIADRILL Ceramic:

2014/35/EU, 2006/42/EG, 2011/65/EU

EN 60745-1, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3

RODIADRILL Ceramic ECO:

2014/35/EU, 2006/42/EG, 2011/65/EU

EN 60745-1, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3

Herstellerunterschrift

Manufacturer / authorized representative signature

ppa. Thorsten Bühl Kelkheim, 22.03.2016

Director Corporate Technology

Technische Unterlagen bei / Technical file at:

ROTHENBERGER Werkzeuge GmbH

Spessartstrasse 2-4

D-65779 Kelkheim/Germany

90700-i5/0118/F&E

www.rothenberger.com

ROTHENBERGER Worldwide

Austria

Belgium

Brazil

Bulgaria

China

Czech

Republic

Denmark

France

Germany

Hungary

India

Greece

ROTHENBERGER Italiana s.r.l.

Via G. Reiss Romoli 17-19 • I-20019 Settimo Milanese

Tel. + 39 02 / 33 50 601 • Fax + 39 02 / 33 50 0151

info@rothenberger.it • www.rothenberger.it

ROTHENBERGER Nederland bv

Postbus 45 • NL-5120 AA Rijen

Tel. + 31 1 61 / 29 35 79 • Fax + 31 1 61 / 29 39 08

info@rothenberger.nl • www.rothenberger.nl

ROTHENBERGER Polska Sp.z.o.o.

Ul. Annopol 4A • Budynek C • PL-03-236 Warszawa

Tel. + 48 22 / 2 13 59 00 • Fax + 48 22 / 2 13 59 01

biuro@rothenberger.pl • www.rothenberger.pl

ROTHENBERGER Russia

Avtosavodskaya str. 25

115280 Moscow, Russia

Tel. + 7 495 / 792 59 44 • Fax + 7 495 / 792 59 46

info@rothenberger.ru • www.rothenberger.ru

ROTHENBERGER-TOOLS SA (PTY) Ltd.

P.O. Box 4360 • Edenvale 1610

165 Vanderbijl Street, Meadowdale Germiston

Gauteng (Johannesburg), South Africa

Tel. + 27 11 / 3 72 96 31 • Fax + 27 11 / 3 72 96 32

info@rothenberger.co.za • www.rothenberger.co.za

ROTHENBERGER S.A.

Ctra. Durango-Elorrio, Km 2 • E-48220 Abadiano

(Vizcaya)

(P.O. Box) 117 • E-48200 Durango (Vizcaya)

Tel. + 34 94 / 6 21 01 00 • Fax + 34 94 / 6 21 01 31

export@rothenberger.es • www.rothenberger.es

ROTHENBERGER Sweden AB

Hemvärnsgatan 22 • S- 171 54 Solna, Sverige

Tel. + 46 8 / 54 60 23 00 • Fax + 46 8 / 54 60 23 01

roswe@rothenberger.se • www.rothenberger.se

ROTHENBERGER (Schweiz) AG

Herostr. 9 • CH-8048 Zürich

Tel. + 41 44 / 435 30 30 • Fax + 41 44 / 401 06 08

[email protected]

ROTHENBERGER TÜRKIYE

ROTHENBERGER Center, Barbaros Bulvarı No:9

TR-34775 Şerifali / Ümraniye-Istanbul

Tel. + 90 / 216 449 24 85 • Fax + 90 / 216 449 24 87

rothenberger@rothenberger.com.tr

www.rothenberger.com.tr

ROTHENBERGER Middle East FZCO

PO Box 261190 • Jebel Ali Free Zone

Dubai, United Arab Emirates

Tel. + 971 / 48 83 97 77 • Fax + 971 / 48 83 97 57

ofce@rothenberger.ae

ROTHENBERGER EQUIPMENT TRADING &

SERVICES LLC

PO Box 91208 • Mussafah Industrial Area

Abu Dhabi, United Arab Emirates

Tel. + 971 / 25 50 01 54 • + 971 / 25 50 01 53

uaesales@rothenberger.ae

ROTHENBERGER UK Limited

2, Kingsthorne Park, Henson Way,

Kettering • GB-Northants NN16 8PX

Tel. + 44 15 36 / 31 03 00 • Fax + 44 15 36 / 31 06 00

info@rothenberger.co.uk

ROTHENBERGER USA LLC

7130 Clinton Road • Loves Park, IL 61111, USA

Tel. +1 / 80 05 45 76 98 • Fax + 1 / 81 56 33 08 79

[email protected]

www.rothenberger-usa.com

Italy

Nether-

lands

Poland

Russia

South

Africa

Spain

Switzerland

Turkey

UAE

UK

USA

ROTHENBERGER Werkzeuge GmbH

Industriestraße 7

D- 65779 Kelkheim / Germany

Telefon + 49 (0) 61 95 / 800 - 0

Fax + 49 (0) 6195 / 800 - 3500

info@rothenberger.com

ROTHENBERGER Australia Pty. Ltd.

Unit 6 • 13 Hoyle Avenue • Castle Hill • N.S.W. 2154

Tel. + 61 2 / 98 99 75 77 • Fax + 61 2 / 98 99 76 77

rothenberger@rothenberger.com.au

www.rothenberger.com.au

ROTHENBERGER Werkzeuge- und Maschinen

Handelsgesellschaft m.b.H.

Gewerbeparkstraße 9 • A-5081 Anif

Tel. + 43 62 46 / 7 20 91-45 • Fax + 43 62 46 / 7 20 91-15

ofce@rothenberger.at • www.rothenberger.at

ROTHENBERGER Benelux bvba

Antwerpsesteenweg 59 • B-2630 Aartselaar

Tel. + 32 3 / 8 77 22 77 • Fax + 32 3 / 8 77 03 94

info@rothenberger.be • www.rothenberger.be

ROTHENBERGER do Brasil LTDA

Av. Fagundes de Oliveira, 538 - Galpão A4

09950-300 - Diadema / SP - Brazil

Tel. + 55 11 / 40 44- 4748 • Fax + 55 11 / 40 44- 5051

spacente@rothenberger.com.br • www.rothenberger.com.br

ROTHENBERGER Bulgaria GmbH

Boul. Sitnjakovo 79 • BG-1111 Soa

Tel. + 35 9 / 2 9 46 14 59 • Fax + 35 9 / 2 9 46 12 05

info@rothenberger.bg • www.rothenberger.bg

ROTHENBERGER Pipe Tool (Shanghai) Co., Ltd.

D-4, No.195 Qianpu Road,East New Area of Songjiang

Industrial Zone, Shanghai 201611, China

Tel. + 86 21 / 67 60 20 61 • + 86 21 / 67 60 20 67

Fax + 86 21 / 67 60 20 63 • ofce@rothenberger.cn

ROTHENBERGER CZ

Prumyslova 1306/7 • 102 00 Praha 10

Tel. +420 271 730 183 • Fax +420 267 310 187

prodej@rothenberger.cz • www.rothenberger.cz

ROTHENBERGER Scandinavia A/S

Smedevænget 8 • DK-9560 Hadsund

Tel. + 45 98 / 15 75 66 • Fax + 45 98 / 15 68 23

roscan@rothenberger.dk

ROTHENBERGER France S.A.

24, rue des Drapiers, BP 45033 • F-57071 Metz Cedex 3

Tel. + 33 3 / 87 74 92 92 • Fax + 33 3 / 87 74 94 03

info-fr@rothenberger.com • www.rothenberger.fr

ROTHENBERGER Deutschland GmbH

Industriestraße 7 • D-65779 Kelkheim/Germany

Tel. + 49 61 95 / 800 81 00 • Fax + 49 61 95 / 800 37 39

verkauf-deutschland@rothenberger.com

www.rothenberger.com

ROTHENBERGER Plastic Technologies GmbH

Lilienthalstraße 71- 87 • D-37235 Hessisch-Lichtenau

Tel. + 49 56 02 / 93 94-0 • Fax + 49 56 02 / 93 94 36

ROTHENBERGER Hellas S.A.

Agias Kyriakis 45 • 17564 Paleo Faliro • Greece

Tel. + 30 210 94 02 049 • +30 210 94 07 302 / 3

Fax + 30 210 / 94 07 322

[email protected] • www.rothenberger.com

ROTHENBERGER Hungary Kft.

Gubacsi út 26 • H-1097 Budapest

Tel. + 36 1 / 3 47- 50 40 • Fax + 36 1 / 3 47 - 50 59

info@rothenberger.hu • www.rothenberger.hu

ROTHENBERGER India Pvt. Ltd.

Plot No 17, Sector - 37, Pace city-I

Gurgaon, Haryana - 122 001, India

Tel. 91124- 4618900 • Fax 91124- 4019471

[email protected]

www.rothenberger.com

Australia

Sweden

Rothenberger Wet drilling machine RODIADRILL Ceramic User manual

Rothenberger Wet drilling machine RODIADRILL Ceramic User manual

in other languages

Related papers

Other documents