Rothenberger Dry drill motor RODIADRILL 1800 DRY User manual

RODIADRILL 1800 DRY

www.rothenberger.com

DE Bedienungsanleitung

EN Instructions for use

FR Instruction d’utilisation

ES Instrucciones de uso

IT Istruzioni d’uso

NL Gebruiksaanwijzing

PT Instruções de serviço

DA Brugsanvisning

SV Bruksanvisning

NO Bruksanvisning

FI Käyttöohje

PL Instrukcja obslugi

CS Návodkpoužívání

TR Kullanim kilavuzu

HU Kezelési útmutató

EL Οδηγίεςχρήσεως

RU Инструкцияпоиспользованию

Overview

D

A CB

F E

A Fitting the drill bit

B Power Puls change over

Ø 32 - Ø 202

Ø 68 / Ø 82

Art. no. FF40185

COverload protection

DSwitching ON / OFF

EHandle attachment

FDust extraction

1

2

3

green red

START STOP

G Operating Instructions

1

2

3

4

5

6

1

2

1

1 2

2

1

Page is loading ...

ENGLISH 9

Contents

Page

1 Safety Notes ........................................................................................................................ 10

1.1 Intended use..................................................................................................................... 10

1.2 General Power Tool Safety Warnings ............................................................................... 10

1.3 Special Safety Instructions ............................................................................................... 11

2 Technical Data .................................................................................................................... 12

3 Electric supply .................................................................................................................... 12

4 Function of the Unit ............................................................................................................ 12

4.1 Fitting the drill bit (A) ......................................................................................................... 12

4.2 Power Puls changeover (B) .............................................................................................. 13

4.3 Overload protection (C) .................................................................................................... 13

4.4 Switching On / Off (D) ....................................................................................................... 13

4.5 Handle attachment (E) ...................................................................................................... 13

4.6 Dust extraction (F) ............................................................................................................ 13

4.7 Operating instructions (G) ................................................................................................. 13

5 Accessories......................................................................................................................... 14

6 Customer service ................................................................................................................ 14

7 Disposal ............................................................................................................................... 14

Markings in this document:

Danger!

This sign warns against the danger of personal injuries.

Caution!

This sign warns against the danger of property damage and damage to the envi-

ronment.

Call for action

10 ENGLISH

1 Safety Notes

1.1 Intended use

The diamond core drill can be used for dry drilling using diamond core bits in brick, masonry,

bricks with holes, sand-lime brick and cellular concrete (not stone and concrete).

The machine is not suitable for wet drilling.

Do not use this product in any other way as stated for normal use. It may only be used when

guided by two hands or when mounted on a diamond drill stand.

1.2 General Power Tool Safety Warnings

WARNING!

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious in-

jury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or bat-

tery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can

cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will in-

crease the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current de-

vice (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, al-

cohol or medication. A moment of in attention while operating power tools may result in se-

rious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropri-

ate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connect-

ing to power source and/or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energising power tools that have the switch on

invites accidents.

ENGLISH 11

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of these devices can reduce dust re-

lated hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The cor-

rect power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamil-

iar with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tools operation. If dam-

aged, have the power tool repaired before use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these instruc-

tions, taking into account the working conditions and the work to be performed. Use

of the power tool for operations different from those intended could result in a hazardous sit-

uation.

5) Service

Have your power tool serviced by a qualified repair person using only identical re-

placement parts. This will ensure that the safety of the power tool is maintained.

1.3 Special Safety Instructions

Wear ear protectors. Exposure to noise can cause hearing loss.

Use auxiliary handles supplied with the tool. Always keep it dry, clean and free of oil and grease.

Loss of control can cause personal injury.

Appliances used at many different locations including open air must be connected via a current

surge preventing switch.

Always wear goggles when using the machine. It is recommended to wear gloves, sturdy non

slipping shoes and apron.

Sawdust and splinters must not be removed while the machine is running.

The dust that arises when working with this tool can be detrimental to health and therefore not

reach the body. Wear a suitable dust protection mask.

Always disconnect the plug from the socket before carrying out any work on the machine.

Only plug-in when machine is switched off.

Keep mains lead clear from working range of the machine. Always lead the cable away behind

you.

When working in walls ceiling, or floor, take care to avoid electric cables and gas or water pipes.

12 ENGLISH

Do not touch a damaged or severed power supply cord when working; pull the plug out of the

power socket immediately instead. Never operate the device with a damaged power supply

cord.

Before beginning your work consult the responsible structural designer to establish the exact

position of the hole to be drilled.

When drilling through a ceiling secure the area from below because the diamond core bit can fall

out.

2 Technical Data

Nominal power output .......................................

1800 W

No-load speed ..................................................

1700 min

-1

Speed under load .............................................

1150 min

-1

Oscillation .........................................................

23000 min

-1

Drilling capacity in concrete ..............................

32 – 202 mm

Tool reception ...................................................

1.1/4“ UNC + G 1/2“

Weight without cable .........................................

5,8 kg

Protection class ................................................

II

Type of protection .............................................

IP 20

Method of operation ..........................................

S3

Operator safety coupling ...................................

yes, electronic limit

Noise pressure level (L

pA

) .................................

92 dB (A) ¦ K

pA

3 dB (A)

Sound power level (L

WA

) ...................................

103 dB (A) ¦ K

WA

3 dB (A)

The noise level during operation can exceed 85 dB (A). Wear hearing protection!

Measured values determined in accordance with EN 60745-1:2010.

Vibration total value .............................................................

5,5 m/s

2

¦ K= 1,5m/s

2

The vibration level given in this information sheet has been measured in accordance with a

standardised test given in EN 60745 and may be used to compare one tool with another. It may

be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool.

However if the tool is used for different applications, with different accessories or

insertion tools or is poorly maintained, the vibration emission may differ. This may

significantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the

times when the tool is switched off or when it is running but not actually doing the

job. This may significantly reduce the exposure level over the total working period.

Identify additional safety measures to protect the operator from the effects of vibra-

tion such as: maintain the tool and the accessories, keep the hands warm, organisa-

tion of work patterns.

3 Electric supply

Connect only to single-phase a.c. current and only to the system voltage indicated on the rating

plate.

It is also possible to connect to sockets without an earthing contact as the design conforms to

safety class II.

4 Function of the Unit

4.1 Fitting the drill bit (A)

Ø 32 - 202 mm (Hollow drill core bits):

 Screw the drill core bit in position.

ENGLISH 13

 Insert the centralizing mandrel.

 Slide the centralizing disc into position.

Ø 68 mm / Ø 82 mm (Recess cutter):

 Screw the adapter (No. FF35097) into position.

 Screw the recess cutter into position.

 Insert the centralizing mandrel (No. FF35096).

To dismantle, use the open-ended spanner to unscrew the drill bits.

4.2 Power Puls changeover (B)

For hard rock, changeover to soft hammer action.

Do not use the hammer action at the start of drilling and for brittle stone (e.g. tiles).

4.3 Overload protection (C)

The green warning lamp is on during normal operation.

If too much pressure is exerted on the drill bit the red warning lamp will come on. Reduce the

pressure and the green lamp will come on again.

In the event of continuous overloading, the electronic system of the machine will switch the ma-

chine off. To continue working, switch the machine off and then on again.

In the case of jerking overload (e.g. drill bit catches) the electronically controlled slipping clutch

will interrupt the power supply.

4.4 Switching On / Off (D)

Switch the machine on or off at the switch button.

The speed can be altered at the switch button.

4.5 Handle attachment (E)

The handle attachment can be fitted on the left or right side.

Extensive torque is created when drilling with core drills; never work without the

handle attachement!

4.6 Dust extraction (F)

Always work with dust extraction switched on. The machine is fitted with an efficient

dust extraction system. We recommend the ROTHENBERGER RODIA DRY

CLEANER 1200 extractor.

1 Slide the extractor adapter on to the spindle.

2 Secure the extractor adapter with springs.

3 Plug in the hose adapter and extractor hose.

4.7 Operating instructions (G)

Depending on the material, select either POWER PULS on or off at the hammer action switch.

1 Position the machine with the centralizing mandrel and switch on.

2 Drill approx. 2 cm using the centralizing mandrel.

3 Switch the machine off and pull it out of the drilled hole.

4 Remove the centralizing mandrel.

5 Insert the core drill into the already cut groove, switch the machine on and drill down to the

required depth.

Pull the machine back slightly from time to time to remove any dust.

6 Switch the machine off and pull it out of the drilled hole. Remove the drilling core.

Bore-holes which don’t have to be applied exactly can be drilled without a centre bit. For that

purpose apply the core cutter slantingly and put the machine slowly straight when a depth of

about 1 cm has been reached.

If drill cores should come loose, take core cutter from the material and remove drill cores.

14 ENGLISH

5 Accessories

Accessory Name

ROTHENBERGER Part Number

Transport case RODIADRILL

FF60185

Centering Pin for extraction rotor, 300 mm

FF03300

Centering Pin for extraction rotor, 400 mm

FF03301

Centering tip “Quick-Out” ICW. FF35097

FF35096

Adaptor for RODIADRILL 1800 DWS/DRY

FF35097

Socket drill bit Ø 68 mm / Ø 82 mm

FF03168 / FF03182

RODIA DRY CLEANER 1200

FF35148

RODIA CLEANER 1400

FF35210

Copper Ring 1.1/4"

FF35190

Sharpening stick (285 x 152 x 40 mm)

FF35135

Extensions G 1/2“:

Nominal length 100 mm

FF35040

Nominal length 200 mm

FF35045

Nominal length 300 mm

FF35050

Nominal length 500 mm

FF35055

Extensions 1.1/4“ UNC:

Nominal length 100 mm

FF35060

Nominal length 200 mm

FF35065

Nominal length 300 mm

FF35070

Nominal length 500 mm

FF35075

6 Customer service

The ROTHENBERGER service locations are available to help you (see listing in catalog or on-

line) and replacement parts and service are also available through these same service locations.

Order your accessories and spare parts from your specialist retailer or using our service-after-

sales hotline:

Phone: + 49 (0) 61 95 / 800 – 8200

Fax: + 49 (0) 61 95 / 800 – 7491

Email: service@rothenberger.com

www.rothenberger.com

7 Disposal

Components of the unit are recyclable material and should be put to recycling. For this purpose

registered and certified recycling companies are available. For an environmental friendly dispos-

al of the non-recyclable parts (e.g. electronic waste) please contact your local waste disposal

authority.

For EU countries only:

Do not dispose electric tools with domestic waste. In accordance with the European

Directive 2012/19/EC the disposal of electrical and electronic equipment and its im-

plementation as national law, electric tools that are no longer serviceable must be

collected separately and utilised for environmentally compatible recycling.

Page is loading ...

EU-KONFORMITÄTSERKLÄRUNG

Wir erklären in alleiniger Verantwortung, dass dieses

Produkt mit den angegebenen Normen und Richtlinien

übereinstimmt.

EU-DECLARATION OF CONFORMITY

We declare on our sole accountability that this product

conforms to the standards and guidelines stated.

DECLARATION EU DE CONFORMITÉ

Nous déclarons sous notre propre responsabilité que ce

produit est conforme aux normes et directives indiquées.

DECLARACION DE CONFORMIDAD EU

Declaramos, bajo nuestra responsabilidad exclusiva, que

este producto cumple con las normas y directivas

mencionadas.

DICHARAZIONE DI CONFORMITÀ EU

Dichiariamo su nostra unica responsabilità, che questo

prodotto è conforme alle norme ed alle direttive indicate.

EU-KONFORMITEITSVERKLARING

Wij verklaren in eigen verantwoordelijkheid dat dit

product overeenstemt met de van toepassing zijnde

normen en richtlijnen.

DECLARAÇÃO DE CONFORMIDADE EU

Declaramos, sob responsabilidade exclusiva, que o

presente produto está conforme com as Normas e

Directivas indicadas.

EU-KONFORMITETSERKLÆRING

Vi erklærer som eneansvarlig, at dette produkt er i

overensstemmelse med anførte standarder,

retningslinjer og direktiver.

EU-FÖRSÄKRAN

Vi försäkrar på eget ansvar att denna produkt uppfyller

de angivna normerna och riktlinjerna.

EU-SAMSVARSERKLÆRING

Vi erklærer på eget ansvar at dette produktet stemmer

overens med de følgende normer eller normative

dokumenter.

TODISTUS EU-STANDARDINMUKAISUUDESTA

Todistamme täten ja vastaamme yksin siitä, että tämä

tuote on allalueteltujen standardien ja

standardomisasiakirjojen vaatimusten mukainen.

DEKLARACJA ZGODNOŚCI EU

Oświadczamy z pełną odpowiedzialnością, że produkt

ten odpowiada wymaganiom następujących norm i

dokumentów normatywnych.

EU-PROHLÁŠENÍ O SHODÌ

Se vší zodpovìdností prohlašujeme, že tento výrobek

odpovídá následujícím normám a normativním

dokumentům.

EU UYGUNLUK BEYANI

Tek sorumlu olarak bu ürünün yönetmelik hükümleri

uyarýnca aþaðýdaki normlara ve norm dokümanlarýna

uygunluðunu beyan ederiz.

EU-AZONOSSÁGI NYILATKOZAT

Teljes felelősségünk tudatában kijelentjük, hogy jelen

termék megfelel a következő szabványoknak vagy

szabványossági dokumentumoknak.

ΔΗΛΩΣΗ ΠΙΣΤΟΤΗΤΑΣ ΕU

Δήλώνουμε με αποκλειστική μας ευθύvη, ότι αυτό το

προϊόv αvταποκρίvεται στα ακόλουθα πρότυπα ή

έγγραφα τυποποίησης.

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ СТАНДАРТАМ

EU.

Мы заявляем что этот продукт соответствует

следующим стандартам.

2014/35/EU, 2006/42/EG, 2011/65/EU

EN 60745-1, EN 55014-1, EN 55014-2,

EN 61000-3-2, EN 61000-3-3

Herstellerunterschrift

Manufacturer / authorized representative signature

ppa. Thorsten Bühl

Kelkheim, 22.03.2016

Director Corporate Technology

Technische Unterlagen bei / Technical file at:

ROTHENBERGER Werkzeuge GmbH

Spessartstrasse 2-4

D-65779 Kelkheim/Germany

90664-i3/0916/F&E

ROTHENBERGER Worldwide

www.rothenberger.com

Austria

Belgium

Brazil

Bulgaria

China

Czech

Republic

Denmark

France

Germany

Hungary

India

Greece

ROTHENBERGER Italiana s.r.l.

Via G. Reiss Romoli 17-19 • I-20019 Settimo Milanese

Tel. + 39 02 / 33 50 601 • Fax + 39 02 / 33 50 0151

info@rothenberger.it • www.rothenberger.it

ROTHENBERGER Nederland bv

Postbus 45 • NL-5120 AA Rijen

Tel. + 31 1 61 / 29 35 79 • Fax + 31 1 61 / 29 39 08

info@rothenberger.nl • www.rothenberger.nl

ROTHENBERGER Polska Sp.z.o.o.

Ul. Annopol 4A • Budynek C • PL-03-236 Warszawa

Tel. + 48 22 / 2 13 59 00 • Fax + 48 22 / 2 13 59 01

biuro@rothenberger.pl • www.rothenberger.pl

ROTHENBERGER Russia

Avtosavodskaya str. 25

115280 Moscow, Russia

Tel. + 7 495 / 792 59 44 • Fax + 7 495 / 792 59 46

info@rothenberger.rz • www.rothenberger.ru

ROTHENBERGER-TOOLS SA (PTY) Ltd.

P.O. Box 4360 • Edenvale 1610

165 Vanderbijl Street, Meadowdale Germiston

Gauteng (Johannesburg), South Africa

Tel. + 27 11 / 3 72 96 31 • Fax + 27 11 / 3 72 96 32

info@rothenberger.co.za • www.rothenberger.co.za

ROTHENBERGER S.A.

Ctra. Durango-Elorrio, Km 2 • E-48220 Abadiano (Vizcaya)

(P.O. Box) 117 • E-48200 Durango (Vizcaya)

Tel. + 34 94 / 6 21 01 00 • Fax + 34 94 / 6 21 01 31

export@rothenberger.es • www.rothenberger.es

ROTHENBERGER Sweden AB

Hemvärnsgatan 22 • S- 171 54 Solna, Sverige

Tel. + 46 8 / 54 60 23 00 • Fax + 46 8 / 54 60 23 01

roswe@rothenberger.se • www.rothenberger.se

ROTHENBERGER (Schweiz) AG

Herostr. 9 • CH-8048 Zürich

Tel. + 41 (0)44 435 30 30 • Fax + 41 (0)44 401 06 08

[email protected]

ROTHENBERGER TÜRKIYE

ROTHENBERGER Center, Barbaros Bulvarı No:9

TR-34775 Şerifali / Ümraniye-Istanbul

Tel. + 90 / 216 449 24 85 • Fax + 90 / 216 449 24 87

rothenberger@rothenberger.com.tr

www.rothenberger.com.tr

ROTHENBERGER Middle East FZCO

PO Box 261190 • Jebel Ali Free Zone

Dubai, United Arab Emirates

Tel. + 971 / 48 83 97 77 • Fax + 971 / 48 83 97 57

ofce@rothenberger.ae

ROTHENBERGER EQUIPMENT TRADING & SERVICES LLC

PO Box 91208 • Mussafah Industrial Area

Abu Dhabi, United Arab Emirates

Tel. + 971 / 25 50 01 54 • + 971 / 25 50 01 53

uaesales@rothenberger.ae

ROTHENBERGER UK Limited

2, Kingsthorne Park, Henson Way,

Kettering • GB-Northants NN16 8PX

Tel. + 44 15 36 / 31 03 00 • Fax + 44 15 36 / 31 06 00

info@rothenberger.co.uk

ROTHENBERGER USA LLC

7130 Clinton Road • Loves Park, IL 61111, USA

Tel. +1 / 80 05 45 76 98 • Fax + 1 / 81 56 33 08 79

[email protected]

www.rothenberger-usa.com

Italy

Netherlands

Poland

Russia

South Africa

Spain

Switzerland

Turkey

UAE

UK

USA

ROTHENBERGER Werkzeuge GmbH

Industriestraße 7

D- 65779 Kelkheim / Germany

Telefon + 49 (0) 61 95 / 800 - 0

Fax + 49 (0) 6195 / 800 - 3500

info@rothenberger.com

ROTHENBERGER Australia Pty. Ltd.

Unit 6 • 13 Hoyle Avenue • Castle Hill • N.S.W. 2154

Tel. + 61 2 / 98 99 75 77 • Fax + 61 2 / 98 99 76 77

rothenberger@rothenberger.com.au

www.rothenberger.com.au

ROTHENBERGER Werkzeuge- und Maschinen

Handelsgesellschaft m.b.H.

Gewerbeparkstraße 9 • A-5081 Anif

Tel. + 43 62 46 / 7 20 91-45 • Fax + 43 62 46 / 7 20 91-15

ofce@rothenberger.at • www.rothenberger.at

ROTHENBERGER Benelux bvba

Antwerpsesteenweg 59 • B-2630 Aartselaar

Tel. + 32 3 / 8 77 22 77 • Fax + 32 3 / 8 77 03 94

info@rothenberger.be • www.rothenberger.be

ROTHENBERGER do Brasil LTDA

Av. Fagundes de Oliveira, 538 - Galpão A4

09950-300 - Diadema / SP - Brazil

Tel. + 55 11 / 40 44- 4748 • Fax + 55 11 / 40 44- 5051

spacente@rothenberger.com.br • www.rothenberger.com.br

ROTHENBERGER Bulgaria GmbH

Boul. Sitnjakovo 79 • BG-1111 Soa

Tel. + 35 9 / 2 9 46 14 59 • Fax + 35 9 / 2 9 46 12 05

info@rothenberger.bg • www.rothenberger.bg

ROTHENBERGER Pipe Tool (Shanghai) Co., Ltd.

D-4, No.195 Qianpu Road,East New Area of Songjiang

Industrial Zone, Shanghai 201611, China

Tel. + 86 21 / 67 60 20 61 • + 86 21 / 67 60 20 67

Fax + 86 21 / 67 60 20 63 • ofce@rothenberger.cn

ROTHENBERGER CZ

Prumyslova 1306/7 • 102 00 Praha 10

Tel. +420 271 730 183 • Fax +420 267 310 187

prodej@rothenberger.cz • www.rothenberger.cz

ROTHENBERGER Scandinavia A/S

Smedevænget 8 • DK-9560 Hadsund

Tel. + 45 98 / 15 75 66 • Fax + 45 98 / 15 68 23

roscan@rothenberger.dk

ROTHENBERGER France S.A.

24, rue des Drapiers, BP 45033 • F-57071 Metz Cedex 3

Tel. + 33 3 / 87 74 92 92 • Fax + 33 3 / 87 74 94 03

info-fr@rothenberger.com • www.rothenberger.fr

ROTHENBERGER Deutschland GmbH

Industriestraße 7 • D-65779 Kelkheim/Germany

Tel. + 49 61 95 / 800 81 00 • Fax + 49 61 95 / 800 37 39

verkauf-deutschland@rothenberger.com

www.rothenberger.com

ROTHENBERGER Plastic Technologies GmbH

Lilienthalstraße 71- 87 • D-37235 Hessisch-Lichtenau

Tel. + 49 56 02 / 93 94-0 • Fax + 49 56 02 / 93 94 36

ROTHENBERGER Hellas S.A.

Agias Kyriakis 45 • 17564 Paleo Faliro • Greece

Tel. + 30 210 94 02 049 • +30 210 94 07 302 / 3

Fax + 30 210 / 94 07 322

[email protected] • www.rothenberger.com

ROTHENBERGER Hungary Kft.

Gubacsi út 26 • H-1097 Budapest

Tel. + 36 1 / 3 47- 50 40 • Fax + 36 1 / 3 47 - 50 59

info@rothenberger.hu • www.rothenberger.hu

ROTHENBERGER India Pvt. Ltd.

Plot No 17, Sector - 37, Pace city-I

Gurgaon, Haryana - 122 001, India

Tel. 91124- 4618900 • Fax 91124- 4019471

[email protected]

www.rothenberger.com

Australia

Sweden

Rothenberger Dry drill motor RODIADRILL 1800 DRY User manual

This manual is also suitable for

Rothenberger Dry drill motor RODIADRILL 1800 DRY User manual

in other languages

Related papers

Other documents