Laserliner AquaPro 120 Plus Set 165 cm Owner's manual

AquaPro

DE

GB

NL

DK

FR

ES

IT

PL

FI

PT

SE

NO

TR

RU

UA

CZ

EE

LV

LT

RO

BG

GR

SI

HU

SK

02

09

16

23

30

37

44

51

58

auto man man

IP 54

Laser

635 nm

Page is loading ...

AquaPro

09

Read the operating instructions and the enclosed brochure „Guarantee

and additional notices“ completely. Follow the instructions they

contain. This document must be kept in a safe place and if the laser

device is passed on, this document must be passed on with it.

!

Automatic rotation laser with slope function

– Horizontally self-levelling by magnetically-dampened pendulum system,

vertical alignment via adjustable base.

– For all horizontal and vertical alignment work.

– The extra vertical reference beam is suitable for dropping a perpendicular

or for aligning partition walls.

– The wall/floor bracket can be used to level the unit vertically or fasten

it to a wall.

– Slope mode makes it possible to lay out slopes.

– Precision 2 mm / 10 m, Self-levelling range, 3.5° with tilt function

General safety instructions

– Attention: Do not look into the direct or reflected beam.

– Do not point the laser beam towards persons.

– If a person‘s eyes are exposed to class 2 laser radiation, they should shut

their eyes and immediately move away from the beam.

– Under no circumstances should optical instruments (magnifying glass,

microscope, binoculars) be used to look at the laser beam or reflections.

– Do not use the laser at eye level (1.40 ...1.90 m)

– Reflective, specular or shiny surfaces must be covered whilst laser

devices are in operation.

– In public areas shield off the laser beam with barriers and partitions

wherever possible and identify the laser area with warning signs.

– Tampering with (making changes to) the laser device is not permitted.

– This device is not a toy - keep out of the reach of children.

Laser radiation!

Do not stare into

the beam!

Class 2 laser

< 1 mw · 635 nm

EN 60825-1:2014

GB

– The device must only be used in accordance with its intended purpose

and within the scope of the specications.

10

L

H

J

K

I

D

G

B

C

A

F

E

P

M

Q

O

N

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

ON/OFF button

Rotation speed selector button

Rotation speed displays

Reference laser outlet

Prism head

Vertical spirit level

Transport lock

Battery compartment

5/8" threads

Adjustment foot

Vertical / wall base

Locking lever

Charger socket (DC 6 V)

Adjustment foot receptacle

Vertical / wall bracket receptacle

Operating / Battery display

Charge display

During transport and in vertical operation, make sure that the

transport securing device (G) is set to „lock“ failure to do

so may result in damage to the device.

!

GB

AquaPro

11

Special product features

Automatic alignment of the device with a magnetically

dampened pendulum system. The device is brought into initial position

and aligns itself autonomously.

Transport LOCK: The device is protected with a pendelum

lock during transport.

Power supply

The device can be operated with standard alkali batteries (6 x type AA).

Insert the batteries as shown by the installation symbols. Ensure the

polarity is correct.

Optional: Charging the batteries

Charge the device‘s battery completely prior to use.

– Open the battery compartment (H), insert the

batteries and connect the plugs to the sockets.

The plugs fit in the sockets in one position only

(see pictures on right). Reclose the battery

compartment.

– Connect the battery charger/mains unit to a

mains source and plug into the socket (M).

Please only use the charger/mains unit supplied

with the device. If a different one is used, the

warranty will become void.

– If the LED (Q) blinks constantly, either the batteries

must be exchanged or recharged.

Horizontal

levelling

Vertical

levelling

Slope

function

90° angle Plumb

function

auto man man

Space grids: These show the laser planes and functions.

auto: Automatic alignment / man: Manual alignment

GB

12

If the unit is currently outside of its automatic levelling range (> 3.5°),

a warning signal will sound and the prism head will not rotate. The

unit must then be placed on a surface which is closer to level. When

in vertical use, the unit does not level itself automatically.

!

Horizontal use of AquaPro

– Set up the unit on a surface that is as level as possible or fasten it to a

tripod.

– Turn the transport lock (G) in the arrow‘s „Unlock“ direction to its limit.

This releases the locking mechanism that protects the pendulum during

transport.

– Press the On/Off button (A).

– Within its range of +/- 3.5°, the unit will level itself automatically and

the prism head will begin to turn.

– The speed of rotation can be changed with the selector button (B),

H = 600 RPM, M = 400 RPM, L = 200 RPM.

Vertical use of AquaPro

– Turn the transport lock (G) in the arrow‘s „Lock“ direction to its limit.

– Hook the vertical/wall bracket into its receptacle (O). To do this, the locking

lever (L) must be in its lower position and the bracket must latch audibly.

To release the bracket, press the locking lever (L) down.

– Align the unit with the adjustment foot (J) as indicated by the vertical

spirit level (F).

– Press the On/Off button (A). The prism head will begin to rotate.

– The speed of rotation can be changed with the selector button (B),

H = 600 RPM, M = 400 RPM, L = 200 RPM.

Always activate the Out-Off-Level function for horizontal levelling.

This is active when the unit is switched on and the transport lock is

turned to its „Unlock” position. If the unit is currently outside of

its automatic levelling range (> 3.5°) , a warning signal will sound and

the prism head will not rotate. The unit must then be placed on a

surface which is closer to level.

!

GB

AquaPro

13

Z

Y

X

Slope mode

To lay out slopes, the Out-Off-Level function

must remain shut off.

– Turn the transport lock (G) in the arrow‘s

„Lock” direction to its limit. Now the tilt

function is inactive and the unit cannot align

itself automatically.

– Press the On/Off button (A). The prism head

will begin to rotate.

– The speed of rotation can be changed with

the selector button (B), H = 600 RPM,

M = 400 RPM, L = 200 RPM.

– Adjust the unit to the desired angle. Slope angle

can be set precisely and quickly with the aid of

the optional angle plate, Art. No.: 080.75. Its

use is simplified in combination with a crank

tripod, e.g. Art. No.: 080.30.

Horizontal levelling cannot be accomplished

in slope mode because the unit cannot

automatically level itself. Refer also to

„Horizontal use of AquaPro“ about this.

!

Art. No.

080.30

X- / Y- / Z-

Axis

Art. No.

080.75

GB

Regularly check the adjustment before use,

after transport and after extended periods of

storage. Always make sure to control all axes.

!

14

EU directives and disposal

This device complies with all necessary standards

for the free movement of goods within the EU.

This product is an electric device and must be

collected separately for disposal according to

the European Directive on waste electrical and

electronic equipment.

Further safety and supplementary notices at:

www.laserliner.com/info

Technical data (Subject to technical alterations)

Self-levelling range ± 3.5° (horizontal)

Precision ± 2 mm / 10 m

Horizontal levelling automatic

Vertical levelling manual

Vertical reference beams 90° to rotation plane

Rotation speed 200, 400, 600 rpm

Laser wavelength 635 nm

Laser Class 2 (EN 60825-1:2014)

Laser output rating < 1 mW

Rechargeable battery life /

Non-rechargeable battery life

approx. 20 h / approx. 45 h,

6 x type AA

Rechargeable battery

recharging time

approx. 14 h

Working temperature range - 10 °C … + 40 °C

Protection class IP 54

Weight 1.7 kg

GB

AquaPro

15

A1

A2

2.

1.

A1

A3

A2

A1

A3

A2

<

2 mm / 10 m = OK

4.

3.

A2

If points A2 and A3 are more than 2 mm / 10 m apart on either

the X, Y or Z axis, the device is in need of adjustment. Contact

your authorised dealer or else the UMAREX-LASERLINER Service

Department.

!

Performing the calibration check

3. Position the device as near as possible to the wall at the height

of point A1. Now adjust the device in the X axis.

4. Turn the device through 180° and mark point A3. The difference

between points A2 and A3 is the tolerance for the X axis.

5. To check the Y and Z axis, repeat steps 3 and 4.

Preparing the calibration check

It is possible for you to check the calibration of the laser. To do this, position

the device midway between 2 walls, which must be at least 5 metres apart.

The best calibration results are achieved if the device is mounted on a tripod.

Switch on the device and determine the marking points using the SensoLite.

Use the precision range on the SensoLite.

1. Mark point A1 on the wall.

2. Turn the device through 180° and mark point A2. You now

have a horizontal reference between points A1 and A2.

GB

Page is loading ...

Laserliner AquaPro 120 Plus Set 165 cm Owner's manual

This manual is also suitable for

Laserliner AquaPro 120 Plus Set 165 cm Owner's manual

in other languages

Related papers

Other documents