Blaupunkt RCM 127 Fitting Instructions Manual

Page is loading ...

- 6 -

Fig.10

Fig.11

2

1

3

15A

1

2V

+12V

per.+12V

+12V

10

CDC A05

7 607 889 093

7 607 647 093

7 607 884 093

Power/Bus 5m

2

1

3

15A

12V

+12V

per.+12V

+12V

10

Power/Bus 5m

7 607 889 093

bl

CDC F05

Opto 5m

rt

Changer

Interface

rt

br

+12V

7 607 647 093

7 607 884 093

+12V

- 7 -

8 622 400 916

Fitting instructions

Instructions de montage

Istruzioni di montaggio

Inbouwinstrukties

Monteringsanvisning

Instrucciones de montaje

Instruções de montagem

Düsseldorf

RCM 127

GB Safety notes

Before starting to mount your car radio, read the mounting and connection

instructions carefully.

Disconnect the vehicle battery’s negative terminal before making connections.

Be sure to observe the safety notes of the automobile manufacturer (airbags, alarm

systems, on-board computers, immobilisers).

Before drilling holes, look to see what is on the other side - making holes into the

battery, wiring looms or fuse box is not recommended!

The positive lead used must have a cross-section of at least 2.5 mm

2

. The set is

protected by a quick-acting 10 A fuse.

During operation of the unit, the set’s side wall may heat up considerably.

Be sure to keep all wires away from hot parts of the housing.

In some vehicles you will find a 20-pin connector pre-fitted in the dashboard’s

installation space. This connector must not be used for connecting the car radio!

In vehicles manufactured by Audi and VW, the 8-pin positive/negative connector

provided in the car must not be connected to a Blaupunkt radio directly! Otherwise

the permanent +12 V line will be short-circuited to ground, leading to serious

damage of the radio’s internal circuitry (burn-out of printed conductor).

F Indications de sécurité

Veuillez lire les instructions de montage et de raccordement avant de monter votre

autoradio.

Débrancher le pôle négatif de la batterie pendant les opérations de montage et de

branchement.

Prendre note des indications de sécurité du fabricant du véhicule (airbag, alarmes,

ordinateur de bord, dispositifs de blocage des roues).

En perçant des trous, veiller à ce que les éléments du véhicule (batterie, câble,

boîte à fusibles) ne soient pas endommagés.

La section du câble positif ne doit pas être inférieure à 2,5 mm.

L’appareil est protégé par un coupe-circuit à action instantanée de 10 A.

La partie latérale de l’autoradio s’échauffe énormément pendant le service de

l’appareil.

Veiller à ce qu’aucun câble ne se trouve sur le boîtier.

Dans certains véhicules une fiche à 20 pôles se trouve dans le compartiment. Ne

pas connecter cette fiche à l’autoradio.

Dans des véhicules Audi/VW, la fiche à 8 pôles prévue dans le véhicule ne doit pas

être connectée directement aux autoradios Blaupunkt; sinon le plus permanent

donnerait court-circuit à la masse et une piste conductive brûlerait dans l’autoradio.

I Note di sicurezza

Prima di effettuare il montaggio della vostra autoradio leggete le istruzioni di

allacciamento.

Per tutta la durata delle operazioni di montaggio e di allacciamento il polo

negativo della batteria deve rimanere distaccato.

Quando si effettua questo intervento bisogna attenersi alle note di sicurezza del

fabbricante d’auto (airbag, impianto di allarme, computer di bordo, bloccaggio di

avvio).

Quando si trapano fori bisogna fare attenzione a non danneggiare nessun

elemento di veicolo (batteria, cavo, scatola dei fusibili).

La sezione del cavo positivo non deve essere inferiore ai 2,5 mm

2

.

L’apparecchio è dotato di un fusibile, 10 A rapido.

Lateralmente la radio si riscalda molto durante l’esercizio.

Bisogna fare attenzione a non far passare dei cavi lungo l’involucro della radio.

In alcuni veicoli è predisposta una spina a 20 poli nel vano di montaggio.

Questa spina non si deve allacciare all’autoradio.

Nelle vetture Audi/VW la spina +/- ad 8 poli non si deve allacciare direttamente

all’autoradio Blaupunkt, altrimenti il polo positivo permanente entrerebbe in

corto circuito con la massa e così si brucerebbe un tratto di conduttura nella

radio.

NL Veiligheidsaanwijzingen

Lees voor het inbouwen van de radio de aanwijzingen voor de inbouw en de

aansluiting.

Tijdens de montage en de aansluiting moet de minpool van de accu worden

ontkoppeld.

Hierbij moeten de veiligheidsvoorschriften van de autofabrikant (airbag,

alarminstallaties, boordcomputer, wegrijbeveiliging) in acht worden genomen.

Let er bij het boren van gaten op dat geen onderdelen van de auto (accu, kabels,

zekeringskasten) beschadigd worden.

De doorsnee van de pluskabel mag niet minder bedragen dan 2,5 mm

2

. Het

apparaat is gezekerd met een zekering van 10A, snel.

Het zijgedeelte van de autoradio wordt tijdens het gebruik zeer heet.

Er moet op worden gelet dat er geen kabels tegen de kast liggen.

Bij enkele autotypes ligt een 20-polige stekker in de inbouwopening. Deze stekker

mag niet op de autoradio worden aangesloten.

Bij auto’s van de merken Audi en VW mag de achtpolige +/-stekker aan de zijde van

de auto niet direct op Blaupunkt-autoradio’s worden aangesloten. Anders wordt

namelijk de continue pluspool kortgesloten met de massa en brandt in de radio een

verbinding door.

S Säkerhetsföreskrifter

Läs noga monterings- och inkopplingsinformationen innan du monterar bilstereon.

Under monterings- och inkopplingstiden skall bilbatteriets minuspol vara lossad.

Beakta biltillverkarens säkerhetsanvisningar (airbag, alarmanläggning, färddator,

startspärr).

Var noga med att inga delar i bilen (batteri, ledningar, säkringshållare) skadas vid

borrning av hål.

Plusledningens area får ej vara mindre än 2,5 mm

2

. Apparaten är avsäkrad med en

10 A snabb säkring.

Bilstereons hölje blir under drift mycket varmt.

Det är därför viktigt att se till att inga kablar ligger emot höljet.

I vissa bilar finnes en 26-polig kontakt i radiouttaget. Denna får ej anslutas direkt

till bilstereon. Använd adapterkabel eller se till att stiftanslutningen blir den rätta.

Eventuella ledningar på stiften 1, 2 och 3 i spänningskontakten måste avlägsnas

från kontaktblocket.

I Audi/VW-bilar får den 8-poliga spänningskontakten ej anslutas direkt till Blaupunkt

bilstereon. Om detta görs brinner en ledningsbana i bilstereon. Använd adapterkabel

eller modifiera bilens spänningskontakt så att stiftanslutningen blir den rätta.

Eventuella leningar på stiften 1,2 och 3 måste avlägsnas från kontakten.

E Instrucciones de montaje

Observaciones de seguridad

Antes de instalar su nuevo equipo, sírvase de leer detenidamente las instrucciones

de montaje y de conexión.

Desconecte el terminal negativo de la batería del vehículo antes de hacer las

conexiones.

Observe las informaciones de seguridad del fabricante del vehículo (con respecto

a airbags, sistema de alarma, ordenador de a bordo, inmovilizador).

Antes de taladrar agujeros, asegúrese de no dañar ningunas partes del vehículo

(batería, cableado, caja de fusibles).

La sección transversal del cable positivo utilizado debe ser de 2.5 mm

2

por lo

menos. El equipo está protegido mediante un fusible de 10 A de acción rápida.

Durante la operación del equipo, la parte lateral de la radio puede calentarse

considerablemente.

Cerciórese de que ninguno de los cables esté en contacto directo con la caja del

autorradio.

En algunos vehículos se encuentra un conector de 20 polos dentro del

compartimiento de instalación del tablero de instrumentos. ¡Este enchufe no debe

utilizarse para efectuar la conexión!

En los modelos de Audi y VW, el conector positivo/negativo de 8 polos provisto no

debe enchufarse directamente en los autorradios Blaupunkt. De lo contrario, la

línea de +12 V permanente se pone en cortocircuito a tierra, lo que dañará

gravemente el autorradio (se quemará un conductor impreso).

P Instruções de segurança

Antes da montagem do seu auto-rádio, ler as instruções de montagem e de

ligação.

Durante o tempo da montagem e da ligação, desapertar o terminal do borne

negativo da bateria.

Seguir as instruções de segurança do construtor do veículo (airbag, sistemas

anti-roubo, computadores de bordo, sistemas imobilizadores).

Na furagem de buracos, dar atenção a não danificar quaisquer peças do

veículo (bateria, cabos, caixa de fusíveis).

O diâmetro do cabo positivo não deve ser inferior a 2,5 mm

2

. O aparelho está

protegido através de um fusível 10 A de acção rápida.

A parte lateral do auto-rádio atinge durante o funcionamento temperaturas

altas.

Dar atenção a que os cabos não fiquem próximos da caixa.

Em alguns veículos, um conector de 20 pinos encontra-se no interior do

compartimento de montagem. Este conector não deve ser ligado ao auto-rádio.

Nos veículos da Audi/VW, o conector +/- de 8 pinos instalado nestes veículos

não deve ser ligado directamente aos auto-rádios da Blaupunkt, caso contrário

o borne continuamente positivo contra massa é curto-circuitado e no rádio

queima-se uma via condutora.

- 8 -

GB

Connection

1 In order to take advantage of the full car radio output and to avoid

incorrect electrical connections with ISO plugs in the vehicle, it is

advisable not to use the vehicle-specific positive/negative connection

for this car radio.

2 You can avoid making incorrect connections by using the vehicle-

specific Blaupunkt adapter wiring, but !

3 Due to the limited cross-section of the wiring in the vehicle, it is

necessary to use the connection cable 7 607 884 093 in addition to

the vehicle-specific Blaupunkt adapter wiring for the positive/

negative connection.

Be sure to observe Fig. 4, 5

Advantage: The vehicle’s wiring system is not damaged.

Positive connection

Cut the permanent +12 volts line from the vehicle-specific Blaupunkt

adapter wiring, join it with connection cable 7 607 884 093 and connect

it directly to the positive terminal of the battery.

Negative connection

Do not connect the negative line to the negative terminal of the battery.

Cut the negative line from the vehicle-specific Blaupunkt adapter wiring,

join it with connection cable 7 607 884 093 and lay the negative line to

a suitable ground, such as a chassis screw, the chassis itself or

corresponding grounds (do not roll up the wiring).

Preparing for the installation of the car radio

The car radio is designed to be installed in the car radio compartment

provided by the vehicle manufacturer. Open the car radio compartment

(remove the shelf or panel by unclipping it) or adjust the size of the car

radio compartment to measure 182 x 53 mm.

For vehicles with deviating installation compartments, Blaupunkt offers

installation kits for 50 mm radio units for the most popular vehicle models.

Check the installation situation in the vehicle and, if necessary, use one

of the special installation kits for specific vehicle models,

e.g. Audi A4/A6/A8: 7 608 021 473

Note:

The mounting bracket included with this car radio is designed for

installation in vehicles with a standard DIN installation compartment

measuring 182 x 53 mm, 165 installation depth and an instrument panel

thickness of approximately 1 to 20 mm in the area of the tab fasteners,

see Fig. 1.

Reach behind the car radio compartment and check to see which tab

fasteners can be bent for the mounting bracket.

Note: Try to be sure to bend all of the tabs.

Place the mounting bracket in the compartment and bend over the tabs

with the help of a screwdriver, see Fig. 1, 2.

Connection, see page 4 or 5 or 6

Connection instructions............................................................... Fig. 4

Positive/negative connection with vehicle-specific

adapter cable .............................................................................. Fig. 5

Positive/negative connection with connection line

7 607 884 093 ........................................................................... Fig. 5a

Equalizer or amplifier connection, (CINCH) ................................ Fig. 6

Do not connect the control wire to terminal 15 (+12 V switched) or

terminal 30 (permanent +12 V), maximum load < 150 mA.

Connection of 4 loudspeakers (4/35 W)...................................... Fig. 7

LF = left front, RF = right front, LR = left rear, RR = right rear.

CD player connection CDC-A06 ................................................. Fig. 8

Connection of IR remote control RC-06 H .................................. Fig. 9

Use the connection cable attached to the remote control.

If necessary, also use cables 7 607 647 093 and 7 607 648 000.

CD player connection CDC-A05 ............................................... Fig. 10

CD player connection CDC-F05 ............................................... Fig. 11

Connection in vehicles with QuickOut

In vehicles equipped with a QuickOut (currently Opel), the QuickOut unit

must be removed and the adapter cable used.

Installing the car radio

Place the car radio in the front of the mounting bracket and push it in until

the side springs snap into position on the left and the right (you will hear

an audible click).

Removing the car radio

Insert the handles into the holes in the panel on the left and right of the

radio and push them in until you hear a distinct click (unlocks side

springs).

Pull the unit out using both handles, see Fig. 3

Note: Handles which have snapped into place can only be

removed after you have pulled the radio out of the

compartment.

DNC (masking of driving noises)

For a description of the equaliser setting and the DNC calibration

process (masking of driving noises) please refer to the owner's manual.

This information is subject to change without notice!

Car radio connection

ISO plug in the vehicle

Car radio connection

with adapter wiring

Car radio connection

with adapter and connection wiring

8 622 400 916

8 601 910 002

2

1

Fig. 2

Fig. 3

Fig. 1

Illustrations

53

182

165

8 601 310 742

1-20

2

5A

+12V/Kl15

+12V

per.+12V

3

1

per.+12V

5A

+12V/Kl15

+12V

+12V / Kl15

+12V

per.+12V

1

5A

12V

5A

per.+12V

7 607 884 093

- 9 -

Connection notes, fig. 4

Negative connection (Ground)

Do not connect the negative line to the negative terminal of the

battery. Lay the negative line to a suitable ground, such as a

chassis screw or the chassis itself. Cut the ground line as

necessary. Then strip the insulation and attach a cable lug

(solder if necessary). Remove the paint of the ground contact

surface and treat with graphite grease (important for a good

ground connection).Screw ground line.

Positive connection +12 V switched (ACC +12 V)

(Ignition)

+12V

When connecting the positive line to terminal 15 of the fuse

box (+12 V via ignition) behind the fuse, it will be possible to

turn the system on and off via the ignition. Also, the unit will

automatically switch off after one hour of playback time to

avoid that the battery goes flat. This hour logic will not be

activated when connecting the permanent

+12 V line (terminal 30).

Permanent +12 V connection

(Battery +12 V)

per. +12V

Do not connect the vehicle’s positive line !

Lay the red positive wire with a 2.5 mm2 cross section to the

battery (do not route close to vehicle harnesses). Connect the

fuse box to protect the positive line and hook up to the

positive terminal of the battery. If necessary, drill a hole into

the splash wall and use a cable duct as required.When

mounting the anti-interference choke coil, wrap in foamed

plastic.

Control wire (Power Antenna +)

+12V

The control wire is the switched positive output for external

pieces of equipment such as a power antenna, maximum load

< 150 mA.

Do not connect the control wire to terminal

15 (+12 V switched) or terminal 30 (permanent +12 V).

Lighting connection (Illumination)

Lighting connection for vehicles with adjustable dashboard

lighting (plus-controlled).

Telephone Mute (low)

When connecting a phone, the car radio will be automatically

muted when making a call.

red / + switched

red / permanent

brown / ground

yello/green / motor antenna

8 622 400 916

orange / Illumination

telephone mute

10A

+12V

+

1

2

3

10A

Kl. 15

Kl.30

1

2

V

10A

Kl.30

1

2

V

15A

10A

per +12V

PIN 2

10A

Page is loading ...

Blaupunkt RCM 127 Fitting Instructions Manual

Blaupunkt RCM 127 Fitting Instructions Manual

in other languages

Related papers

Other documents