Anolis ArcPar™ 100 User manual

Brand: Anolis

Model: ArcPar™ 100

Category: Stroboscopes & disco lights

Type: User manual

Version 1.4 CE

Table of contents

1. Safety instructions ......................................................................................................... 3

2. Fixture exterior view ...................................................................................................... 5

3. Installation....................................................................................................................... 6

3.1 Connection to the mains ............................................................................................ 6

3.2 Installing the diffusion lter ......................................................................................... 7

3.3 Installing barndoors and the gel frame ....................................................................... 8

3.4 Rigging the xture .................................................................................................... 10

3.5 DMX-512 connection ................................................................................................ 12

3.6. Wireless DMX operation ......................................................................................... 13

3.7. Stand-alone and Master/Slave operation ................................................................ 14

4. Control menu map ........................................................................................................ 15

5. Robin ArcPar 100 - DMX chart..................................................................................... 17

5.1 Virtual colour wheel - colour mixing chart ................................................................20

5.2 LED zone order ........................................................................................................ 24

6. Control menu (Standard and Easy control mode) ..................................................... 25

6.1 Addressing and master/slave setting (DMXA) .........................................................25

6.2 Fixture information (Info) .......................................................................................... 26

6.3 Personality (Pers) ..................................................................................................... 26

6.4 Manual Control (Manual) .......................................................................................... 27

6.5 Test program (Test Prg) ........................................................................................... 27

6.6 Stand-alone (St Alone) ............................................................................................. 27

6.7 Special functions (Special) ....................................................................................... 28

7. RDM ............................................................................................................................... 29

8. Error and information messages ................................................................................ 30

9. Technical Specications.............................................................................................. 30

10. Maintenance and cleaning ......................................................................................... 33

11. ChangeLog ................................................................................................................. 34

12. Photometric diagrams................................................................................................ 34

ArcPar 100

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE POWERING OR INSTALLING YOUR ArcPar 100 !

Save it for future reference.

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to

ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning

notes written in this manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this

manual or any unauthorized modication to the device.

Please consider that damages caused by manual modications to the device are not subject to warranty.

The ArcPar 100 was designed for indoor use and it is intended for

professional application only. It is not for household use.

1. Safety instructions

DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS

UNIT!

Make sure that the available voltage is not higher than stated on the rear panel of the xture.

This xture should be operated only from the type of power source indicated on the marking label. If you are

not sure of the type of power supplied, consult your authorized distributor or local power company.

Always disconnect the xture from AC power before cleaning, removing or installing the fuses, or any part.

The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords

as this canresult in re or electric shock.

Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by

persons walking on it.

Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power

cord from time to time.

Refer servicing to qualied service personnel.

This xture falls under protection class I. Therefore this xture has to be connected to

a mains socket outlet with a protective earthing connection.

Do not connect this xture to a dimmer pack.

LED light emission. Risk of eye injury. Do not look into the beam at a distance of less

than 2 meters from the front surface of the product. Do not view the light output with

optical instruments or any device that may conncentrate the beam

If the xture has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on

immediately. The arising condensation water might damage your device. Leave the device switched off until

it has reached room temperature.

Do not shake the xture. Avoid brute force when installing or operating the xture.

This xture was designed for indoor use only, do not expose this unit to rain or use near water.

When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, moisture

or dust.

Air vents and slots in the xture´s head and base are provided for ventilation, to ensure reliable operation of

the device and to protect it from overheating.

Do not block the LEDs array with any object when the xture is under operation.

The openings should never be covered with cloth or other materials, and never must be blocked.

This xture should not be placed in a built-in installation unless proper ventilation is provided.

Only operate the xture after having checked that the housing is rmly closed and all screws are tightly faste-

ned.

Always use a secondary safety cable when mounting this xture.

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xtu-

re.

Do not block the front objective LEDs with any object when the xture is under operation.

The xture becomes very hot during operation. Allow the xture to cool approximately 20 minutes prior to

manipulate with it.

Operate the xture only after having familiarized with its functions. Do not permit operation by persons not

qualied for operating the xture. Most damages are the result of unprofessional operation!

Please use the original packaging if the xture is to be transported.

Please consider that unauthorized modications on the xture are forbidden due to safety reasons!

If this device will be operated in any way different to the one described in this manual, the product may suffer

damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-

circuit, burns, electric shock, crash etc.

2. Fixture exterior view

4 - DMX OUT

5 - DMX IN

6 - Fuse holder

7 - Mains IN

8 - Mains OUT

9 - Display and control buttonsns

10 - Safety wire attachment pointt

1 - Mounting holder

2 - Tilt locks

3 - Lens array

3. Installation

Fixtures must be installed by a Qualied electrician in accordance with all

national and local electrical and construction codes and regulation.

3.1 Connection to the mains

For protection from electric shock, the xture must be earthed!

The ArcPar 100 is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC

power source from 100-240 Volts.

Install a suitable plug on the power cord, note that the cores in the power cord are coloured according to the

following table. The earth has to be connected!

If you have any doubts about proper installation, consult a qualied electrician.

Core (EU) Core (US) Connection Plug Terminal Marking

Brown Black Live L

Light blue White Neutral N

Yellow/Green Green Earth

This device falls under class one and must be earthed (grounded)!

Design of the ArcPar 100 allows to connect several xtures to AC mains power in one interconnected daisy

chain using power input and throughput connectors. Needed daisy chain cords are stated in the chapter

“Technical specications “

The max. number of connected xtures depends on the AC mains power voltage:

12 xtures at power supply= 230V

10 xtures at power supply= 208V

6 xtures at power supply= 120V

Do not overload the supply line and the connecting leads.

Wiring and connection work must be carried out by qualied staff!

3.2 Installing the diffusion lter

Disconnect the xture from mains before diffusion lter installation

1. Disconnect the xture from mains.

2. Insert the screw (1) with the plastic washer (2) into diffuser (3) and secure it by means of the

plastic washer (4.)

2. Insert the diffuser (3) into the ArcPar 100 and secure it by screwing the screw (1) into the thread hole (5)

in the plastic eggcrate. Keep the correct orientation of the diffuser sections (6).

3.3 Installing barndoors and the gel frame

Disconnect the xture from mains before barndoors and the gel frame installation

1.Disconnect the xture from mains.

2. Screw the accessory frame adaptor (1) on the ArcPar 100 housing with the four screws M4x8 (2) and unlock

the spring lock (3) via pushing this spring lock as show red arrows on the picture.

3. Insert the gel frame (4) into the bottom slots of the accessory frame adaptor (1).

4. Insert the barndoors (5) into the top slots of the accessory frame adaptor (1).

5. Secure both accessories by moving the spring lock (3) up as shows the red arrow on the picture.

Note: the barndoors can be rotated to desired position and secured in this position via the securing screw

(6).

3.4 Rigging the xture

A structure intended for installation of the xture (s) must safely hold weight of the xture(s) placed on it. The

structure has to be certicated to the purpose.

The xture (xtures) must be installed in accordance with national and local electrical and construction codes

and regulation.

For overhead installation, the xture must be always secured with a safety wire

When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,

under high working places and other endangered areas is forbidden.

The operator has to make sure that safety-relating and machine-technical installations are approved by an expert

before taking into operation for the rst time and after changes before taking into operation another time.

The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled

person once a year.

Allow the xture to cool for ten minutes before handling.

The projector should be installed outside areas where persons may walk by or be seated.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working

load limits, installation material being used, and periodic safety inspection of all installation material and the

projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional

companies.

CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety

of a possible installation, do not install the xture!

The xture has to be installed out of the reach of public.

The xture must never be xed swinging freely in the room.

When installing the device, make sure there is no highly inammable

material (decoration articles, etc.) in a distance of min. 0.4 m.

CAUTION!

Use an appropriate clamp to rig the xture on the truss.

Make sure that the device is xed properly! Ensure that the

structure (truss) to which you are attaching the xtures is secure.

For overhead installation, install a safety wire that can hold at least 10 times the weight of the xture. Use only

safety wire with screw-on carabine. Fasten the safety cable in the attachment point and around the truss

as shown on the picture below.

When installing xtures side-by-side, avoid illuminating one xture with

another!

1-Clamp

2-Trust

3-Safety wire

4-Attachment point

5-Folded mounting yoke

3.5 DMX-512 connection

The xture is equipped with 5-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair

cable designed for RS-485 and 5-pin XLR-plugs and connectors in order to connect the controller with the

xture or one xture with another.

If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with

the DMX input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-out-

puts, you need to use adapter-cables.

Building a serial DMX-chain:

Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture. Always

connect one output with the input of the next xture until all xtures are connected. Up to 32 xtures can be

interconnected.

Caution: At the last xture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω resistor

between Signal (–) and Signal (+) into a 5-pin XLR-plug and plug it in the DMX-output of the last xture.

DMX output DMX input

XLR socket: XLRplug:

1 - Shield

2 - Signal (-)

3 - Signal (+)

4 - Used for wireless DMX

5 - Used for wireless DMX

1 - Shield

2 - Signal (-)

3 - Signal (+)

4 - Used for wireless DMX

5 - Used for wireless DMX

3.6. Wireless DMX operation

The external Robe Wireless CRMX-LB100 module allows receiving wireless DMX. This device is equipped

with the Lumen Radio CRMX module and antenna for receiving DMX signal. CRMX module operates on the

2.4 GHz band.

Push in the 5-pin XLR plug (1) into 5-pin XLR sockit (4) and simultaneously locating pin (2) into hole (5) in the

xture. In this way the wireless DMX module is connected with the xture.

NOTE: when you disconnecting the DMX wireless module from the xture, press and hold lock (5) during get-

ting the wireless module out.

To link the xture with DMX transmitter.

The xture can be only linked with the transmitter by running the link procedure at DMX transmitter .

After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Stat“ (Special -->Vireless --

>Stat).

To unlink the xture from DMX transmitter.

The xture can be unlinked from receiver via the menu item “ Unlink“ (Special-->Vireless -->Unlink.).

1 - 5-pin XLR (female)

2 - Locating pin

3 - Lock

Robe Wireless CRMX-LB100

3.7. Stand-alone and Master/Slave operation

The xtures on a data link are not connected to the controller but can execute pre-set programs which can be

different for every xture. To set the program to be played, see the "Mast/Sla" menu (DMXA ---> Mast/Sla).

The Stand-alone operation can be applied to the single xture or to multiple xtures operating synchronously.

Synchronous operation of multiple xtures requires that they must be connected on a data link and one of them

is set as a master (master mode) and the rest as the slaves (slave mode). To set the xture as the master or

the slave, see the "Mast/Sla" menu.

The master xture starts simultaneous program start in the other slave xtures. All xtures have a denite, syn-

chronized starting point when playing back their programs. Every slave runs its program according to the program

number of the master. E.g. if the master runs program number 3, all slaves run their programs number 3.

Note: if the option "Play Master" is selected at the xture, this slave will play master´s program number 3, in-

stead of its own program 3.

Every xture runs its program repeatedly, starting the program step No.1 when requested by the master.

If the slave xture has a shorter program length, it will continuously repeat its program until the master xture

nishes its own program and restarts its program running (slave 1- prog. step 3 will not be nished) -see the

picture below.

If the slave xture has a longer program length, it will restart at prog. step 1 before it completes all its prog.

steps (slave 2 - prog. step 5 will not be played) - see the picture below.

Note: Disconnect the xtures from the DMX controller before master/slave operating, otherwise data collisions

can occur and xtures will not work properly!

4. Control menu map

Default settings=Bold print

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7

DMXA Set DMXA 001-512

DMX Pres Mode 1

Mode 7

Mast/Sla Off

Master Play Prog 1

Play Prog All

Slave Play Master

Play Slave

Info POn Time Total

Reset

DMX In

Powr 0-255

Dim F 0-255

Temp Current

Highest

High Res

Sw Ver IC-1

IC-2

Pers

DMX Pres Mode 1

Mode 7

Display Turn

On/Off T On, Off

Contrast 0-100%

Backlight 0-100%

C Cal M

On, Off

C Mix M RGBW, CMY

Mic Sens 0...10...19

Fans Auto, High, Silen

Temp Uni °C, °F

I Ef Pos Pan

Dimm F

Store

Defaults

Manual Pres Eff R L 1 Pos 1-Pos 5

Dimm Pos 1- Pos 5

Manual C Powr 0-255

Dim F 0-255

Test Prg

Sta Alone Music T On, Off

Auto Run Off

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7

Prog 1

All

Pr Play Prog 1

All

Pr Edit Prog 1 Step 1 Powr

Prog 2 : :

Prog 3 Step 40 F.Tim 0-25.5

S.Tim 0-25.5

COPY

Prg En 1-40

Special RDM Low

RDM Hight

Wireless Stat

Unlink

Adjust DMX Val Powr 0-255

Dim F 0-255

Calib Cal Col Red C 0-255

Grn C 0-255

Blu C

0-255

Whi C 0-255

Store

Cal Load Yes,

Sw Upd On, Off

5. Robin ArcPar 100 - DMX chart

Version 1.4 Mode 1- Standard 16 bit, Mode 2 - Reduced 8bit, Mode 3 - Basic,

Mode 4 - Extended 16bit, Mode 5 - Robin 100 LedBeam compatible, Mode 6 - RGBW, Mode 7 - RGBWSD

Mode/Channel

Value Function

Type of

control

1 2 3 4 5 6 7

- - - - 1 - -

No function

- - - - 2 - -

No function

- - - - 3 - -

No function

- - - - 4 - -

No function

- - - - 5 - -

No function

1 1 1 1 6 - -

0 - 29

30 - 39

40 - 49

50-109

110-114

115-119

120-124

125-129

130-145

146-161

162-255

Special functions

Reserved

To activate following functions (30-129DMX), stop in DMX value

for at least 3sec. and shutter must be closed at least 3sec. (Shutter

channel 12/8/3/28/33 must be at range of 0-31DMX). Correspon-

ding menu items are temporily overrided.

RGBW colour mixing mode

CMY colour mixing mode

Reserved

Colour calibration mode On

Colour calibration mode Off

Audio control On

Audio control Off

-------------------------------------------------------------------------------------

Effect speed control, slow--> fast

Effect speed control, fast--> slow /opposite direction/

Reserved

step

proportional

2 2 - - - 1 1

0-255

Red/Cyan (8 bit) - all zones

Red LEDs saturation control (0-100%) proportional

3 - - - - - -

0-255

Red/Cyan ne(16 bit) - all zones

Fine red LEDs saturation control proportional

4 3 - - - 2 2

0-255

Green/Magenta (8 bit) - all zones

Green LEDs saturation control (0-100%) proportional

5 - - - - - -

0-255

Green/Magenta ne (16 bit) - all zones

Fine green LEDs saturation control proportional

6 4 - - - 3 3

0-255

Blue/Yellow (8 bit) - all zones

Blue LEDs saturation control (0-100%) proportional

7 - - - - - -

0-255

Blue/Yellow ne (16 bit) - all zones

Fine blue LEDs saturation control proportional

8 5 - - - 4 4

0-255

White (8 bit) - all zones

If RGBW mode is selected:

White colour saturation control coarse (0-100%)

If CMY mode is selected:

No function

proportional

9 - - - - - -

0-255

White ne (16 bit) - all zones

Fine white LEDs saturation control (RGBW mode) proportional

- - - 2 7 - -

0-255

Red/Cyan (8 bit) - zone 1

Red LEDs saturation control (0-100%) proportional

- - - 3 8 - -

0-255

Red/Cyan ne (16 bit) - zone 1

Fine red LEDs saturation control proportional

- - - 4 9 - -

0-255

Green/Magenta (8 bit) - zone 1

Green LEDs saturation control (0-100%) proportional

- - - 5 10 - -

0-255

Green/Magenta ne (16 bit) - zone 1

Fine green LEDs saturation control proportional

Mode/Channel

Value Function

Type of

control

1 2 3 4 5 6 7

- - - 6 11 - -

0-255

Blue/Yellow (8 bit) zone 1

Blue LEDs saturation control (0-100%) proportional

- - - 7 12 - -

0-255

Blue/Yellow (16 bit) zone 1

Fine blue LEDs saturation control) proportional

- - - 8 13 - -

0-255

White (8 bit) - zone 1

If RGBW mode is selected:

White colour saturation control coarse (0-100%)

If CMY mode is selected:

No function

proportional

- - - 9 14 - -

0-255

White (16 bit) - zone 1

Fine white LEDs saturation control (RGBW mode) proportional

- - - 10 15 - -

0-255

Red/Cyan ( 8bit) - zone 2

Red LEDs saturation control (0-100%) proportional

- - - 11 16 - -

0-255

Red/Cyan ne (16 bit) - zone 2

Fine red LEDs saturation control proportional

- - - 12 17 - -

0-255

Green/Magenta (8 bit) - zone 2

Green LEDs saturation control (0-100%) proportional

- - - 13 18 - -

0-255

Green/Magenta ne (16 bit) - zone 2

Fine green LEDs saturation control proportional

- - - 14 19 - -

0-255

Blue/Yellow (8 bit) - zone 2

Blue LEDs saturation control (0-100%) proportional

- - - 15 20 - -

0-255

Blue/Yellow ne (16 bit) - zone 2

Fine blue LEDs saturation control proportional

- - - 16 21 - -

0-255

White (8 bit) - zone 2

If RGBW mode is selected:

White colour saturation control coarse (0-100%)

If CMY mode is selected:

No function

proportional

- - - 17 22 - -

0-255

White (16 bit) - zone 2

Fine white LEDs saturation control (RGBW mode) proportional

- - - 18 23 - -

0-255

Red/Cyan (8 bit) - zone 3

Red LEDs saturation control (0-100%) proportional

- - - 19 24 - -

0-255

Red/ Cyan ne (16 bit) - zone 3

Fine red LEDs saturation control proportional

- - - 20 25 - -

0-255

Green/Magenta (8 bit) - zone 3

Green LEDs saturation control (0-100%) proportional

- - - 21 26 - -

0-255

Green/Magenta ne (16 bit) - zone 3

Fine green LEDs saturation control proportional

- - - 22 27 - -

0-255

Blue/Yellow (8 bit) zone 3

Blue LEDs saturation control (0-100%) proportional

- - - 23 28 - -

0-255

Blue/Yellow ne (16 bit) zone 3

Fine blue LEDs saturation control proportional

- - - 24 29 - -

0-255

White (8 bit) zone 3

If RGBW mode is selected:

White colour saturation control coarse (0-100%)

If CMY mode is selected:

No function

proportional

- - - 25 30 - -

0-255

White ne (16 bit) zone 3

Fine white LEDs saturation control (RGBW mode) proportional

10 6 - 26 31 - -

1-255

CTC

No function

Colour temperature correction from 19000K to 2700K

step

proportional

Mode/Channel

Value Function

Type of

control

1 2 3 4 5 6 7

11 7 2 27 32 - -

1-2

4-5

7-9

10-12

13-15

17-55

57 - 95

97 – 134

135

136 - 174

175

176 -214

215

216 - 246

247

248

249

250

251

252

253

254

255

Virtual Colour Wheel

For detailed description see " Virtual colour wheel- colour mixing chart

No function

White 2700 K

White 2700 K (Halogen lamp mode*)

White 3200 K

White 3200 K (Halogen lamp mode*)

White 4200 K

White 5600 K

White 8000 K

Blue (Blue=full, Red+Green+White=0)

Red=0, Green->up,Blue =full, White=0

Light Blue (Red=0, Green=full, Blue =full, White=0)

Red=0, Green=full, Blue->down, White=0

Green (Red=0, Green=full, Blue =0, White=0)

Red->up, Green=full, Blue=0, White=0

Yellow (Red=full, Green=full, Blue=0, White=0)

Red=full, Green->down, Blue=0, White=0

Red(Red=full, Green=0, Blue=0, White=0)

Red=full, Green=0, Blue->up, White=0

Magenta (Red=full, Green=0, Blue=full, White=0)

Red -> down, Green=0, Blue=full, White=0

Blue (Red=0, Green=0, Blue=full, White=0)

Item Audio control = Off (channel Special Functions).

The following effects can be controlled by the channel Special

Functions (DMX values of 130-161)

Item Audio control = On (channel Special Functions).

The following effects are controlled by sound

Rainbow effect (with fade time)

Rainbow effect

Zone effect 1

Zone effect 2

Zone effect 3

Zone effect 4

Zone effect 5

Random colour selection

step

proportional

step

proportional

step

proportional

step

proportional

step

proportional

step

proportional

step

12 8 3 28 33 - 5

0-31

32-63

64-95

96-127

128-143

144-159

160-175

176-191

192-223

224-255

Shutter/Strobe

Shutter closed

Strobe effect from slow--> fast (zones 2,3 only)

Strobe effect from slow--> fast (All zones together)

Reserved

Opening pulses in sequences from slow--> fast

(All zones together)

Closing pulses in sequences from fast--> slow

(All zones together)

Random strobe effect from slow--> fast (random zone)

Random strobe effect from slow--> fast (random zone + random

strobe)

Random strobe effect from slow --> fast (All zones together)

Shutter open

step

proportional

step

13 9 4 29 34 - 6

0-255

Dimmer (8 bit)

Dimmer intensity from 0% to 100% proportional

14 - - 30 35 - -

0-255

Dimmer ne (16 bit)

Fine dimming proportional

*In the Halogen lamp mode the Dimmer channel imitates behaviour of the halogen lamp during dimming.

5.1 Virtual colour wheel - colour mixing chart

Scale*

Virtual Colour Wheel

Red

Green

Blue

White

DMX

1-2 (White 2700K) 250 118 0 63

3 (White 2700K /Hal.mode/) 250 118 0 63

4-5 (White 3200K) 255 141 5 89

6 (White 3200K /Hal.mode/) 255 141 5 89

7-9 (White 4200K) 254 141 3 255

10-12 (White 5600K) 254 207 37 255

13-15 (White 8000K) 228 255 79 255

16 0 0 255 0

17 0 3 255 0

18 0 6 255 0

19 0 9 255 0

20 0 12 255 0

21 0 15 255 0

22 0 18 255 0

23 0 21 255 0

24 0 24 255 0

25 0 27 255 0

26 0 30 255 0

27 0 36 255 0

28 0 41 255 0

29 0 46 255 0

30 0 52 255 0

31 0 58 255 0

32 0 64 255 0

33 0 68 255 0

34 0 74 255 0

35 0 80 255 0

36 0 86 255 0

37 0 92 255 0

38 0 98 255 0

39 0 104 255 0

40 0 110 255 0

41 0 119 255 0

42 0 129 255 0

43 0 138 255 0

44 0 147 255 0

45 0 156 255 0

46 0 165 255 0

47 0 174 255 0

48 0 183 255 0

49 0 192 255 0

50 0 201 255 0

51 0 210 255 0

52 0 219 255 0

53 0 228 255 0

54 0 237 255 0

55 0 246 255 0

56 0 255 255 0

57 0 255 246 0

58 0 255 237 0

59 0 255 228 0

60 0 255 219 0

61 0 255 210 0

62 0 255 201 0

255

192

Page 1

Page is loading ...

Anolis ArcPar™ 100 User manual

Brand: Anolis

Model: ArcPar™ 100

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

Anolis ArcPar™ 100 User manual

Anolis ArcPar™ 100 User manual

Related papers

Other documents