Kenwood DDX7017 User manual

Category
Car video systems
Type
User manual
© B54-4467-00/00 (KV/RV)
DDX8017
DDX7017
DDX7047
MONITOR WITH DVD RECEIVER
INSTALLATION MANUAL
MONITEUR AVEC REPTEUR DVD
MANUEL D'INSTALLATION
MONITOR CON RECEPTOR DVD
MANUAL DE INSTALACION
MONITOR COM RECEPTOR DVD
MANUAL DE INSTALAÇAO
2
|
English
Accessories
1
..........1
2
..........1
3
..........1
4
..........2
5
..........6
6
..........6
7
..........1
English
|
3
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire connections
for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
2WARNING
• If you connect the ignition wire (red) and the
battery wire (yellow) to the car chassis (ground),
you may cause a short circuit, that in turn may start
a fire. Always connect those wires to the power
source running through the fuse box.
• Do not cut out the fuse from the ignition wire (red)
and the battery wire (yellow). The power supply
must be connected to the wires via the fuse.
2CAUTION
• If your car’s ignition does not have an ACC position,
connect the ignition wires to a power source that
can be turned on and off with the ignition key. If
you connect the ignition wire to a power source
with a constant voltage supply, as with battery
wires, the battery may die.
• If the console has a lid, make sure to install the
unit so that the faceplate will not hit the lid when
closing and opening.
• If the fuse blows, first make sure the wires aren’t
touching to cause a short circuit, then replace the
old fuse with one with the same rating.
• Insulate unconnected wires with vinyl tape or other
similar material. To prevent a short circuit, do not
remove the caps on the ends of the unconnected
wires or the terminals.
• Connect the speaker wires correctly to the terminals
to which they correspond. The unit may be
damaged or fail to work if you share the - wires or
ground them to any metal part in the car.
• When only two speakers are being connected to the
system, connect the connectors either to both the
front output terminals or to both the rear output
terminals (do not mix front and rear). For example,
if you connect the + connector of the left speaker
to a front output terminal, do not connect the -
connector to a rear output terminal.
• After the unit is installed, check whether the brake
lamps, blinkers, wipers, etc. on the car are working
properly.
• Mount the unit so that the mounting angle is 30° or
less.
4
|
English
Connection
TV ANTENNA INPUT
TO MONITOR UNIT
B
C
B
C
PRK SW
+
+
B
C
A
A
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
Connection cable (Included in the disc changer)
Antenna Cord
FM/AM antenna input
Connect to the vehicle's parking brake detection switch harness
using the supplied relay connector.
To Vehicle's reverse lamp harness
To car light control switch
Reveres sensor wire (Pink)
For the sake of safety, be sure to connect the parking sensor.
Dimmer control wire (Orange/White)
When using the optional power amplifier,
connect to its power control terminal.
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.
TV tuner (Optional)
Parking sensor wire (Green)
Battery wire
(Yellow)
Ground wire (Black) - (To car chassis)
( 5A )
Ignition wire (Red)
If no connections are made, do not let
the cable come out from the tab.
Steering remote control input
(Light Blue/Yellow)
To Steering remote
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
Depending on what antenna you are using,
connect either to the control terminal of the
motor antenna, or to the power terminal for the
booster amplifier of the film-type antenna.
Battery wire (Yellow)
Ground wire (Black) - (To car chassis)
If no connections are made, do not let the cable come out from the tab.
Mute wire (Brown)
Motor antenna control wire
(Blue)
Power control wire
(Blue/White)
External amplifier control wire
(Pink/Black)
To connect the Kenwood navigation system,
consult your navigation manual.
Ignition key
switch
ACC
Car fuse
box
(Main fuse)
Battery
Car fuse box
Disc Changer etc.(Optional)
English
|
5
+
+
+
+
FRONT LFRONT RREAR LREAR R
ANT. CONT
P CONT
EXT.CONT
REVERSE
ILLUMI
REMO.CONT
MUTE
IConnection cable
(Included in the
Navigation system)
Connection cable
(Included in the TV tuner)
Wiring harness
(Accessory 1)
To front left speaker
Wiring harness
(Accessory 2)
Rear view
Navigation System
(Optional)
To front right speaker
To rear left speaker
To rear right speaker
White/Black
White
Gray/Black
Gray
Green/Black.
Green
Purple
Purple/Black
6
|
English
FRONT
REAR
WOOFER
SUB
CENTER
AV OUT
AV IN 2
CAMERA
REAR VIEW
AV IN 1
AV OUT
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Rear View Camera Input
Visual input (Yellow)
Audio/Visual Output
Visual output (Yellow)
Audio/Visual input 1
Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Audio/Visual input 2
Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Center Preout (DDX8017 only)
System Connection (DDX8017/DDX7017)
Do not connect.
To Disc Changer etc.
To Navigation System
To TV Tuner unit
Audio/Visual Output
• Audio left output (White)
• Audio right output (Red)
English
|
7
FRONT
REAR
WOOFER
SUB
AV OUT
CAMERA
REAR VIEW
AV IN
AV OUT
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Rear View Camera Input
Visual input (Yellow)
Audio/Visual Output
• Audio left output (White)
• Audio right output (Red)
Audio/Visual input
Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
System Connection (DDX7047)
To Disc Changer etc.
To Navigation System
To TV Tuner unit
Do not connect.
Audio/Visual Output
Visual output (Yellow)
8
|
English
Installation for Monitor/Player Unit
Accessory 3
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Metal mounting strap
(commercially available)
Self-tapping screw
(commercially available)
Screw (M4X8)
(commercially available)
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
Firewall or metal support
English
|
9
Installation on Toyota, Nissan or Mitsubishi Car using Brackets
Installing in Japanese-Made Cars
Car Bracket
Accessory 5 (M5x6mm)
or Accessory 6 (M5x7mm)
Accessory 5 (M5x6mm)
or Accessory 6 (M5x7mm)
10
|
English
Installation of Remote control unit
Install the remote control unit holder (Accessory 7).
Double-stick tape
(included)
Remote control holder 7
To prevent the Remote control unit from dropping down under your foot, install it using the
Remote control unit holder. If the Remote control unit drops down under driving pedals, it will
interfere with your driving and may result in a traffic accident.
English
|
11
Removing Monitor Unit
Removing the Hard Rubber Frame (escutcheon)
1. Engage the catch pins on the removal tool 4
and remove the two locks on the lower level.
Lower the frame and pull it forward as shown
in the figure.
2. When the lower level is removed, remove the
upper two locations.
Removing the Unit
1. Remove the hard rubber frame by referring
to the removal procedure in the section
<Removing the Hard Rubber Frame>.
2. Remove the Hex-head screw with integral
washer (M4 × 8) on the back panel.
3. Insert the two removal tools 4 deeply into
the slots on each side, as shown.
4. Lower the removal tool toward the bottom,
and pull out the unit halfway while pressing
towards the inside.
5. Pull the unit all the way out with your hands,
being careful not to drop it.
Be careful to avoid injury from the catch pins on
the removal tool.
The frame can be removed from the top side in
the same manner.
Removal Tool (Accessory 4)
Lock
Catch
Removal Tool
(Accessory 4)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Kenwood DDX7017 User manual

Category
Car video systems
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI