Sony STR-ZA1100ES User manual

Category
AV receivers
Type
User manual

This manual is also suitable for

STR-ZA3100ES/STR-ZA2100ES/STR-ZA1100ES
MULTI CHANNEL
AV RECEIVER
Installation Guide
US
Guide d’installation
FR
Guía de instalación
ES
Before installing the receiver, be sure to update the receiver to the latest software
version.
Avant d’installer l’ampli-tuner, veillez à le mettre à jour à la dernière version de logiciel.
Antes de instalar el receptor, asegúrese de actualizar el receptor a la versión de software
más reciente.
2
US
Map of GUI menu system
Using the home menu
Menu items underlined are default settings.
Home
Watch
BD/DVD
SAT/CATV
GAME
STB
VIDEO
TV
Listen
AUX
SACD/CD
FM TUNER
AM TUNER
Custom Preset
Movie
Music
Party
Night
Sound Effects
Sound Field 2ch Stereo
Direct
Auto Format Decoding
Dolby Surround
Neural:X
Multi Stereo
Equalizer
Sound Optimizer
Normal
Low
Off
InCeiling Speaker Mode Front & Center
Front
Off
Pure Direct
On
Off
3
US
Zone Controls
Zone2 Power
On
Off
Zone2 Input
SOURCE
BD/DVD
SAT/CATV
GAME
STB
VIDEO
AUX
TV
SA-CD/CD
FM TUNER
AM TUNER
Zone2 Volume
(+23.0dB, +22.5dB, …, 40.0dB, …, –92.0dB, –∞dB)
Zone3 Power
On
Off
Zone3 Input
SOURCE
VIDEO
AUX
TV
SA-CD/CD
FM TUNER
AM TUNER
Zone3 Volume
(+23.0dB, +22.5dB, …, 40.0dB, …, –92.0dB, –∞dB)
Setup
Input Setup
1), 2)
Icon
Name
Watch/Listen
Show/Hide
HDMI
OPTICAL/COAXIAL
COMPONENT
VIDEO IN
AUDIO IN
Input Mode
Preset Sound Field
In-Ceiling Speaker Mode
A/V Sync
Subwoofer Low Pass Filter
Subwoofer Level
Preset Gain Level
Trigger 1
3)
Trigger 2
3)
Trigger 3
3)
Trigger
4)
4
US
Setup
Speaker Setup
Auto Calibration
5)
Automatic Phase Matching
(Auto, Off)
Calibration Type
(Full Flat, Engineer, Front Reference, Off)
Speaker Pattern
Speaker Connections
SB Speaker Assign
(Zone2, Bi-Amp, Front B, Off)
Size
6)
(Large, Small)
Distance
6)
(32ft 9in, 32ft 8in, …, 9ft 10in, …,
6ft7in, 6ft 6in)
Level
6)
(+10.0dB, +9.5dB, …, 0.0dB, …, –9.5dB,
10.0dB)
Test Tone
5)
Crossover Frequency
6)
(40Hz, 50Hz, …, 120Hz, …, 190Hz, 200Hz)
Equalizer
6)
(+10.0dB, +9.0dB, …, 0.0dB, …, –9.0dB,
10.0dB)
Center Speaker Lift Up
(10, 9, 8, …, 2, 1, Off)
Surround Speaker Position
(Front, Back)
Speaker Relocation
(Type A, Type B, Off)
Ceiling Height
(32ft 9in, 32ft 8in, …, 9ft 0in, …,
6ft7in, 6ft 6in)
Distance Unit
(feet, meter)
Network Setup
Internet Setup
5)
Information
5)
Network Standby (On, Off)
Music Connect
Device1 Connected Device
Input for Music Connect1
Preset Volume
Output Zone
Device2 Connected Device
Input for Music Connect2
Preset Volume
Output Zone
Audio Setup
Digital Legato Linear (Auto 1, Auto 2, Off)
Sound Optimizer
(Normal, Low, Off)
Sound Field
2ch Stereo
Direct
Auto Format Decoding
Dolby Surround
Neural:X
Multi Stereo
In-Ceiling Speaker Mode
(Front & Center, Front, Off)
Pure Direct
(On, Off)
Subwoofer Low Pass Filter
(On, Off)
A/V Sync
(300ms, 290ms, …, 10ms, 0ms,
HDMIAuto)
Dual Mono
(Main, Sub, Main/Sub)
Dynamic Range
Compressor
(Auto, On, Off)
Neural:X
(On, Off)
5
US
Setup
HDMI Setup
4K Scaling
(Auto, Off)
Control for HDMI
(On, Off)
Standby Linked to TV
(Auto, On, Off)
Audio Return Channel
(eARC, ARC, Off)
Standby Through
(Auto, On, Off)
Audio Out
(AMP, TV+AMP)
Zone2 Audio Out
(AMP, Zone2 TV+AMP, Zone2 AMP)
Subwoofer Level
(Auto, +10dB, 0dB)
HDMI Out B Mode
(Main, Zone2)
Priority
(Main & Zone2, Main Only)
Fast View
(Auto, Off)
HDMI Signal Format
HDMI IN 1
(Standard format,
Enhanced format)
HDMI IN 2
(Standard format,
Enhanced format)
HDMI IN 3
(Standard format,
Enhanced format)
HDMI IN 4
(Standard format,
Enhanced format)
HDMI IN 5
(Standard format,
Enhanced format)
Zone Setup
Zone Controls Zone2 Power (On, Off)
Zone2 Input
(SOURCE, BD/DVD, …,
FM TUNER, AM TUNER)
Zone2 Volume
(+23.0dB, +22.5dB, …,
40.0dB, …, –92.0dB,
–∞dB)
Zone3 Power
(On, Off)
Zone3 Input (SOURCE, VIDEO, …,
FM TUNER, AM TUNER)
Zone3 Volume
(+23.0dB, +22.5dB, …,
40.0dB, …, –92.0dB,
–∞dB)
Main Preset Volume
(+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)
Main Max Volume
(+23.0dB, +22.5dB, ..., –40.0dB)
Zone2 Preset Volume
(+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)
Zone2 Max Volume
(+23.0dB, +22.5dB, ..., –40.0dB)
Zone2 Line Out
(Variable, Fixed)
Zone3 Preset Volume
(+23.0dB, +22.5dB, …, –92.0dB, –∞dB, Off)
Zone3 Max Volume
(+23.0dB, +22.5dB, ..., –40.0dB)
Zone3 Line Out
(Variable, Fixed)
6
US
Setup
System Setup
Language
(English, Español, Français)
Auto Display
(On, Off)
Auto Standby
(On, Off)
Volume Display
(Relative, Absolute)
Dimmer
(Bright, Dark, Off)
Sleep
(2:00:00, 1:30:00, 1:00:00, 0:30:00, Off)
Software Version
Network Update
USB Update
5)
Tuner Setup FM Mode
Name Input
Preset Gain Level
Install Setup
External Control
(On, Off)
Trigger 1
3), 5)
Trigger 2
3), 5)
Trigger 3
3), 5)
Trigger
4), 5)
Test Picture for HDMI
Out A
(4K/60Hz/4:4:4, 4K/24Hz/4:4:4,
1080p/60Hz, 480p/60Hz, Off)
Test Picture for HDMI
Out B
(4K/60Hz/4:4:4
7)
, 4K/24Hz/4:4:4,
1080p/60Hz, 480p/60Hz, Off)
Save/Load
5)
Settings Lock (On, Off)
Easy Setup
Auto Calibration
5)
Internet Setup
5)
1)
You can select the following inputs in the Input Setup screen.
BD/DVD, SAT/CATV, GAME, STB, VIDEO, AUX, TV, SA-CD/CD
2)
You can set up each input using these menu items in [Input Setup].
3)
STR-ZA3100ES only
4)
STR-ZA2100ES/STR-ZA1100ES only
5)
Detailed information of these menu items is displayed after you select the settings.
6)
The menu item can be adjusted against each speaker.
7)
This parameter cannot be selected when [Zone2] is selected for [HDMI OUT B Mode].
7
US
Table of Contents
Map of GUI menu system ................................................................................................2
Using the home menu ......................................................................................2
Preparations
Preparing the receiver ......................................................................................................8
Outline dimensional drawing ...........................................................................8
Attaching/removing the front cover ................................................................8
Mounting the receiver using the rack mount kit .............................................................9
Connections
Connecting a 4K TV that supports HDCP 2.2 and a 4K streaming box
using a 4K-compatible HDMI cable ........................................................................... 10
Making a connection for PoE (Power over Ethernet) (for STR-ZA3100ES only) ............. 11
Making a multi-zone connection .................................................................................... 12
Speaker patterns and terminals to be connected ..........................................................13
Settings
Setting up the receiver .................................................................................................... 17
Activating the network standby mode ...........................................................17
Turning on the control mode to make an external controller connection .....17
Outputting a test tone from each speaker (TestTone) ................................... 17
Displaying a test screen (Test Picture) ............................................................17
Adjusting the sound balance automatically (Auto Calibration) .....................17
List of messages after Auto Calibration measurements ............................... 18
Saving/loading settings of the receiver ........................................................ 18
Linking with a Hi-Fi music system .................................................................. 19
Mixing separate audio/video inputs (Last video mode) ............................... 19
Setting the in-ceiling speaker mode .............................................................. 19
Setting HDMI signal formats ........................................................................... 19
Updating the software via the network .........................................................20
Updating the software with a USB flash drive ...............................................20
Setting up through a web browser ................................................................20
Using the PING button ...................................................................................20
When using an ARC-compatible TV that supports Dolby Atmos audio
output .......................................................................................................21
When using an eARC-compatible TV that supports Dolby Atmos and
DTS:X audio output ..................................................................................21
Configuring the receiver to allow a Crestron Control System to control
the receiver .............................................................................................. 22
Using the hidden commands
Performing commands using the receiver .................................................................... 23
Performing commands using the supplied remote control ......................................... 23
Changing the remote control code ............................................................... 23
Turning on transmitting mode of the discrete code for the main zone ........24
Turning on transmitting mode of the discrete code for Zone 2/Zone 3 ......25
Useful information
Zone distribution ............................................................................................................26
8
US
Preparations
Preparing the receiver
Outline dimensional drawing
Top
Front Side
174 mm (6 7/8 in)
430 mm (17 in) 378 mm (15 in)
410 mm (16 1/4 in)
10 mm (13/32 in)
Attaching/removing the front cover
The front cover can be completely removed from the receiver.
Remove the front cover by inserting
your fingers under the cover.
9
US
Preparations
Mounting the receiver using the rack
mount kit
Make sure to use a “WS-RE1” dedicated rack mount kit for
this receiver when mounting the receiver on a rack mount.
1 Check that all parts are included.
Bracket × 2
Insulator
Blank panel × 1
Insulator
Screw
+P U10-32×3/4 (inch)*
× 6
Screw
+T M5×18 (mm)*
× 6
* Select the correct screws according to the type of rack.
Washer × 6
2 Remove screws from the right side of the
receiver. Do not remove screws other than those
specified.
3 Mount the bracket on the right side of the
receiver in the order of the step numbers
printed on the bracket using the screws
removed in step 2.
4 Repeat steps 2 and 3 for the left side to mount
the bracket.
5 Mount the receiver to the rack system. Make
sure to perform this step with more than one
person.
Rack mount
6 Mount the blank panel.
(The blank panel hides the legs of the receiver to
give it a cleaner look. Aligning the height of the
receiver and blank panel lets it fit into a 4U size
space.)
10
US
Connections
Connecting a 4K TV that supports HDCP 2.2 and a 4K streaming box
using a 4K-compatible HDMI cable
To enjoy audio from 4K content such as 4K movies, connect the HDMI output/input jacks of
each device that supports HDCP 2.2* using HDMI cables, as illustrated below.
In this section, the STR-ZA3100ES is used for illustrative purposes.
* HDCP 2.2 (Highbandwidth Digital Content Protection System Revision 2.2) is newly enhanced copyright
protection technology that is used to protect content such as 4K movies from Studios.
4K media player 4K TV or 4K projector
Connect the receiver to a 4K media player
using a High Speed HDMI cable (not
supplied).
Connect the receiver to a 4K TV or a 4K
projector using a High Speed HDMI cable
(not supplied).
If you are using an FMP‐X10/X5 Media
Player:
Connect the cable to the HDMI OUT 1 (for AUDIO VIDEO) jack
of the player.
Select [ (Settings)]  [Sound]  [Audio from HDMI OUT]
 [HDMI OUT 1] in the Home menu of the FMP-X10/X5 Media
Player after Initial Setup is complete.
If you are using a different 4K media
player:
Connect the cable to one of the HDCP 2.2-compatible
HDMI output jacks. For details, refer to the operating
instructions supplied with your player.
If you are using a BRAVIA TV with the
series name X950B, X900B or X850B:
Connect the cable to the HDMI IN 1 jack of your TV.
If you are using a different 4K TV or 4K
projector:
Connect to one of the HDCP 2.2-compatible HDMI input
jacks. If the jack is not compatible with the eARC (Enhanced
Audio Return Channel) or ARC (Audio Return Channel)
function, also connect an optical digital cable. For details, refer
to the operating instructions supplied with your 4K TV or 4K
projector.
Note
• Sony recommends that you use an HDMI cable made by Sony or another HDMI-authorized cable. Be
sure to use a High Speed HDMI Cable with Ethernet. Premium High Speed HDMI Cable with Ethernet that
supports 18 Gbps is required for 4K/60p 4:4:4, 4:2:2, and 4K/60p 4:2:0 10 bit, etc.
11
US
Connections
Making a connection for PoE (Power over Ethernet) (for STR-ZA3100ES only)
The following illustration is an example of configuration of a home network with the receiver
and a computer.
LAN cable
Modem
Wireless access point, etc.
Network camera, etc.
LAN cable
LAN cable
LAN cable
Computer
Router
Internet
Notes
• Connect a router to one of ports 1 to 8 on the receiver using a single LAN cable. Do not connect the
same router to the receiver using more than one LAN cable. Doing so may cause a malfunction.
• Ports No. 1 and No. 2 support PoE (Power over Ethernet, Alternative A). If you connect a PoE-compatible
device to one of these ports, power will be supplied to the device from the receiver.
• You can also connect a device that does not support PoE to the PoE port.
• The PoE port lights in red while supplying power.
• This receiver supports PoE Class 3.
• We recommend using a Category 7 cable.
STR-ZA3100ES
12
US
Making a multi-zone connection
This receiver allows various multi-zone connections.
Sample setup
5.1-channel speaker system with Zone 2 connection
Connected device Zone Connection Operation on the receiver
Speakers Main • Connect 5-channel speakers to SPEAKERS FRONT A,
CENTER and SURROUND terminals.
• Connect 1 or 2 subwoofer(s) to PRE OUT subwoofer
jack(s).
Perform Auto Calibration, and then select [Setup] -
[Speaker Setup] - [SB Speaker Assign] - [Zone2] from
the home menu.
Tip
• Select [Setup] - [Input Setup] -
[In-Ceiling Speaker Mode] - [On] when you use the
in-ceiling speakers in the main zone.
Zone2 Connect left and right speakers to
SPEAKERS SURROUND BACK/HEIGHT
(FRONT B/BI-AMP/ZONE 2) terminals.
TV Main Connect to the HDMI OUT A jack. Press HDMI OUT to select HDMI OUT A.
Zone2 Connect to the HDMI OUT B jack. Select [Setup] - [HDMI Setup] from the home menu,
and then configure each setting as follows.
• HDMI Out B Mode: Zone2
• Zone2 Audio Out: Zone2 TV + AMP
13
US
Connections
Speaker patterns and terminals to be connected
When you connect speakers to the receiver, refer to the following table.
You can use the following table to confirm the speaker patterns supported by the receiver as
well as the speaker terminals to which the speakers of each speaker pattern are to be
connected.
When playing back DTS content, select a speaker pattern which supports DTS playback*
(indicated with white background in the following table). If you select other speaker patterns
(indicated with gray background in the table), the sound may not be output from some
speakers.
To set the speaker pattern, select [Setup] - [Speaker Setup] - [Speaker Pattern] from the home
menu.
* Due to the receiver’s system limitations
The abbreviations and symbol used in the list are as follows.
FH: Front high speakers
TF: Top front speakers
TM: Top middle speakers
TR: Top rear speakers
RH: Rear high speakers
FD: Front Dolby Atmos enabled speakers
SRD: Surround Dolby Atmos enabled speakers
SBD: Surround back Dolby Atmos enabled speakers
SB: SPEAKERS SURROUND BACK/HEIGHT
(FRONT B/BI-AMP/ZONE 2) terminals
What the numbers in the speaker pattern indicate:
5 . 1 . 2
Number of speakers
located at listener’s
level
Number of
subwoofers
Number of height or
overhead (top) speakers
STR-ZA3100ES/STR-ZA2100ES
Speaker pattern
SPEAKERS terminals PRE OUT jacks
Zone 2 connection/
Front B speaker connection/
Bi-amplifier connection
FRONT A
CENTER SURROUND
SURROUND BACK/HEIGHT
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT
SUBWOOFER
2.0
- - - - - SB
2.0.2 (TM)
- -
(TM)*
- - SB
2.0.2 (FD)
- -
(FD)*
- - SB
2.1
- - - -
SB
2.1.2 (TM)
- -
(TM)*
-
SB
2.1.2 (FD)
- -
(FD)*
-
SB
3.0
- - - - SB
3.0.2 (TM)
-
(TM)*
- - SB
3.0.2 (FD)
-
(FD)*
- - SB
3.1
- - -
SB
3.1.2 (TM)
-
(TM)*
-
SB
3.1.2 (FD)
-
(FD)*
-
SB
4.0
-
- - - SB
4.0.2 (FH)
-
(FH)*
- - SB
4.0.2 (TM)
-
(TM)*
- - SB
4.0.2 (FD)
-
(FD)*
- - SB
4.0.2 (SRD)
-
(SRD)*
- - SB
4.0.4 (FH+TM)
-
(FH) (TM)
-
Not available
4.0.4 (FH+TR)
-
(FH) (TR)
-
Not available
4.0.4 (FH+RH)
-
(FH) (RH)
-
Not available
4.0.4 (TF+TM)
-
(TF) (TM)
-
Not available
4.0.4 (TF+TR)
-
(TF) (TR)
-
Not available
4.0.4 (TF+RH)
-
(TF) (RH)
-
Not available
14
US
Speaker pattern
SPEAKERS terminals PRE OUT jacks
Zone 2 connection/
Front B speaker connection/
Bi-amplifier connection
FRONT A
CENTER SURROUND
SURROUND BACK/HEIGHT
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT
SUBWOOFER
4.0.4 (TM+TR)
-
(TM) (TR)
-
Not available
4.0.4 (TM+RH)
-
(TM) (RH)
-
Not available
4.0.4 (FD+SRD)
-
(FD) (SRD)
-
Not available
4.1
-
- -
SB
4.1.2 (FH)
-
(FH)*
-
SB
4.1.2 (TM)
-
(TM)*
-
SB
4.1.2 (FD)
-
(FD)*
-
SB
4.1.2 (SRD)
-
(SRD)*
-
SB
4.1.4 (FH+TM)
-
(FH) (TM)
Not available
4.1.4 (FH+TR)
-
(FH) (TR)
Not available
4.1.4 (FH+RH)
-
(FH) (RH)
Not available
4.1.4 (TF+TM)
-
(TF) (TM)
Not available
4.1.4 (TF+TR)
-
(TF) (TR)
Not available
4.1.4 (TF+RH)
-
(TF) (RH)
Not available
4.1.4 (TM+TR)
-
(TM) (TR)
Not available
4.1.4 (TM+RH)
-
(TM) (RH)
Not available
4.1.4 (FD+SRD)
-
(FD) (SRD)
Not available
5.0
- - - SB
5.0.2 (FH)
(FH)*
- - SB
5.0.2 (TM)
(TM)*
- - SB
5.0.2 (FD)
(FD)*
- - SB
5.0.2 (SRD)
(SRD)*
- - SB
5.0.4 (FH+TM)
(FH) (TM)
-
Not available
5.0.4 (FH+TR)
(FH) (TR)
-
Not available
5.0.4 (FH+RH)
(FH) (RH)
-
Not available
5.0.4 (TF+TM)
(TF) (TM)
-
Not available
5.0.4 (TF+TR)
(TF) (TR)
-
Not available
5.0.4 (TF+RH)
(TF) (RH)
-
Not available
5.0.4 (TM+TR)
(TM) (TR)
-
Not available
5.0.4 (TM+RH)
(TM) (RH)
-
Not available
5.0.4 (FD+SRD)
(FD) (SRD)
-
Not available
5.1
- -
SB
5.1.2 (FH)
(FH)*
-
SB
5.1.2 (TM)
(TM)*
-
SB
5.1.2 (FD)
(FD)*
-
SB
5.1.2 (SRD)
(SRD)*
-
SB
5.1.4 (FH+TM)
(FH) (TM)
Not available
5.1.4 (FH+TR)
(FH) (TR)
Not available
5.1.4 (FH+RH)
(FH) (RH)
Not available
5.1.4 (TF+TM)
(TF) (TM)
Not available
5.1.4 (TF+TR)
(TF) (TR)
Not available
5.1.4 (TF+RH)
(TF) (RH)
Not available
5.1.4 (TM+TR)
(TM) (TR)
Not available
5.1.4 (TM+RH)
(TM) (RH)
Not available
5.1.4 (FD+SRD)
(FD) (SRD)
Not available
5.0 (SB)
-
(SB Single)
- -
Not available
5.0.2 (SB+FH)
-
(SB Single) (FH)
-
Not available
5.0.2 (SB+TM)
-
(SB Single) (TM)
-
Not available
5.0.2 (SB+FD)
-
(SB Single) (FD)
-
Not available
5.0.2 (SB+SRD)
-
(SB Single) (SRD)
-
Not available
5.1 (SB)
-
(SB Single)
-
Not available
5.1.2 (SB+FH)
-
(SB Single) (FH)
Not available
5.1.2 (SB+TM)
-
(SB Single) (TM)
Not available
5.1.2 (SB+FD)
-
(SB Single) (FD)
Not available
15
US
Connections
Speaker pattern
SPEAKERS terminals PRE OUT jacks
Zone 2 connection/
Front B speaker connection/
Bi-amplifier connection
FRONT A
CENTER SURROUND
SURROUND BACK/HEIGHT
(FRONT B/BI-AMP/ZONE 2)
(L/R)
HEIGHT
SUBWOOFER
5.1.2 (SB+SRD)
-
(SB Single) (SRD)
Not available
6.0 (SB)
(SB Single)
- -
Not available
6.0.2 (SB+FH)
(SB Single) (FH)
-
Not available
6.0.2 (SB+TM)
(SB Single) (TM)
-
Not available
6.0.2 (SB+FD)
(SB Single) (FD)
-
Not available
6.0.2 (SB+SRD)
(SB Single) (SRD)
-
Not available
6.1 (SB)
(SB Single)
-
Not available
6.1.2 (SB+FH)
(SB Single) (FH)
Not available
6.1.2 (SB+TM)
(SB Single) (TM)
Not available
6.1.2 (SB+FD)
(SB Single) (FD)
Not available
6.1.2 (SB+SRD)
(SB Single) (SRD)
Not available
6.0
-
- -
Not available
6.0.2 (FH)
-
(FH)
-
Not available
6.0.2 (TM)
-
(TM)
-
Not available
6.0.2 (FD)
-
(FD)
-
Not available
6.0.2 (SRD)
-
(SRD)
-
Not available
6.0.2 (SBD)
-
(SBD)
-
Not available
6.1
-
-
Not available
6.1.2 (FH)
-
(FH)
Not available
6.1.2 (TM)
-
(TM)
Not available
6.1.2 (FD)
-
(FD)
Not available
6.1.2 (SRD)
-
(SRD)
Not available
6.1.2 (SBD)
-
(SBD)
Not available
7.0
- -
Not available
7.0.2 (FH)
(FH)
-
Not available
7.0.2 (TM)
(TM)
-
Not available
7.0.2 (FD)
(FD)
-
Not available
7.0.2 (SRD)
(SRD)
-
Not available
7.0.2 (SBD)
(SBD)
-
Not available
7.1
-
Not available
7.1.2 (FH)
(FH)
Not available
7.1.2 (TM)
(TM)
Not available
7.1.2 (FD)
(FD)
Not available
7.1.2 (SRD)
(SRD)
Not available
7.1.2 (SBD)
(SBD)
Not available
* If you are connecting speakers to SPEAKERS SURROUND BACK/HEIGHT (FRONT B/BI-AMP/ZONE 2)
terminals for Zone 2, front B speaker or bi-amplifier connection, set [Speaker Setup] -
[SB Speaker Assign] to [Zone2], [Front B] or [Bi-amp] and use the PRE OUT HEIGHT jacks for height
speakers.
16
US
STR-ZA1100ES
Speaker
pattern
SPEAKERS terminals PRE OUT jacks
Zone 2 connection/
Front B speaker connection/
Bi-amplifier connection
FRONT A
CENTER SURROUND
SURROUND BACK/HEIGHT
(FRONT B/BI-AMP/ZONE 2)
(L/R)
SUBWOOFER
2.0
- - - - SB
2.0.2 (TM)
- -
(TM)
- Not Available
2.0.2 (FD)
- -
(FD)
- Not Available
2.1
- - -
SB
2.1.2 (TM)
- -
(TM)
Not Available
2.1.2 (FD)
- -
(FD)
Not Available
3.0
- - - SB
3.0.2 (TM)
-
(TM)
- Not Available
3.0.2 (FD)
-
(FD)
- Not Available
3.1
- -
SB
3.1.2 (TM)
-
(TM)
Not Available
3.1.2 (FD)
-
(FD)
Not Available
4.0
-
- - SB
4.0.2 (FH)
-
(FH)
- Not Available
4.0.2 (TM)
-
(TM)
- Not Available
4.0.2 (FD)
-
(FD)
- Not Available
4.0.2 (SRD)
-
(SRD)
- Not Available
4.1
-
-
SB
4.1.2 (FH)
-
(FH)
Not Available
4.1.2 (TM)
-
(TM)
Not Available
4.1.2 (FD)
-
(FD)
Not Available
4.1.2 (SRD)
-
(SRD)
Not Available
5.0
- - SB
5.0.2 (FH)
(FH)
- Not Available
5.0.2 (TM)
(TM)
- Not Available
5.0.2 (FD)
(FD)
- Not Available
5.0.2 (SRD)
(SRD)
- Not Available
5.1
-
SB
5.1.2 (FH)
(FH)
Not Available
5.1.2 (TM)
(TM)
Not Available
5.1.2 (FD)
(FD)
Not Available
5.1.2 (SRD)
(SRD)
Not Available
5.0 (SB)
-
(SB Single)
- Not Available
5.1 (SB)
-
(SB Single)
Not Available
6.0 (SB)
(SB Single)
- Not Available
6.1 (SB)
(SB Single)
Not Available
6.0
-
- Not Available
6.1
-
Not Available
7.0
- Not Available
7.1
Not Available
17
US
Settings
Settings
Setting up the receiver
Activating the network standby mode
You can keep the network function active even when the
receiver is in standby mode.
1 Select [Setup] - [Network Setup] - [Network
Standby] from the home menu.
2 Select [On].
Note
• When the receiver is in standby mode, the (power) indicator on
the front panel lights up in amber if [Network Standby] is set to
[On].
Turning on the control mode to make an
external controller connection
You can control the receiver from external devices.
1 Select [Setup] - [Install Setup] - [External Control]
from the home menu.
2 Select [On].
Note
• Set [External Control] to [On] to activate the network connection or
to activate control from an external controller connected to the
RS232C port.
Outputting a test tone from each speaker
(TestTone)
You can output a test tone from each speaker in sequence.
1 Select [Setup] - [Speaker Setup] - [Test Tone]
from the home menu.
2 Select the setting you want.
For STR-ZA3100ES/STR-ZA2100ES
Off
Auto: The test tone is output from each speaker in
sequence.
Front L, Center, Front R, Surround R, Sur Back R, Sur
Back*, Sur Back L, Surround L, Height1 L, Height1 R,
Height2 R, Height2 L, Subwoofer: You can select
which speakers will output the test tone.
For STR-ZA1100ES
Off
Auto: The test tone is output from each speaker in
sequence.
Front L, Center, Front R, Surround R, Sur Back R, Sur
Back*, Sur Back L, Surround L, Height L, Height R,
Subwoofer: You can select which speakers will
output the test tone.
* [Sur Back] appears when only one surround back speaker is
connected.
3 Adjust the speaker level.
Tips
• You can set a test tone by pressing the TEST TONE button on the
remote control. In this case, you can only use the display panel for
the operation.
• To adjust the level of all speakers at the same time, press +/–.
You can also use MASTER VOLUME on the receiver.
• The adjusted value is shown on the TV screen while adjusting.
Displaying a test screen (Test Picture)
Display a test screen for HDMI OUT A and HDMI OUT B jacks.
1 Press TEST PICTURE on the remote control.
Tips
• A test picture is output in 480p from both the HDMI OUT A and
HDMI OUT B jack.
If you want to output a test picture in another resolution, select
[Setup] - [Install Setup] - [Test Picture for HDMI Out A] or [Test
Picture for HDMI Out B] from the home menu, and then select the
resolution setting you want.
• HDMI audio signals are not output while the test screen is
displayed.
Adjusting the sound balance automatically
(Auto Calibration)
This receiver is equipped with a D.C.A.C. (Digital Cinema
Auto Calibration) function, which allows you to perform
automatic calibration.
Auto Calibration allows you to perform automatic calibration
as follows.
Check the connection between each speaker and the
receiver.
Adjust the speaker level.
Measure the distance of each speaker from your seating
position.*
Measure the speaker size.*
Measure the frequency characteristics (EQ).*
Measure the frequency characteristics (Phase).* *
* The measurement result is not utilized when [Direct] is selected.
* The measurement result may be not utilized, depending on the
audio formats.
Note
• The D.C.A.C. is designed to achieve proper sound balance for your
room. However, you can adjust the speaker levels manually
according to your preference using Test Tone.
1 Set up each speaker correctly, and then connect
the calibration microphone.
2 Select [Setup] - [Speaker Setup] - [Auto
Calibration] from the home menu.
3 Follow the instructions on the TV screen, then
press to select [Start].
The measurement starts in 5seconds.
The measurement process will take approximately
30seconds with a test tone.
When the measurement ends, a beep sounds and the
screen switches.
4 Select the item you want.
Save: Saves the measurement results and exits the
setting process.
Retry: Performs the Auto Calibration again.
Discard: Exits the setting process without saving the
measurement results.
18
US
5 Save the measurement results.
Select [Save] in step4.
Calibration Matching
When Auto Calibration is executed, this function works
automatically to match the distance and level of the right
and left speakers. You can set this function only after the
D.C.A.C. measurement process has been completed and the
results of D.C.A.C. measurement are saved. The setting is
valid until you change it.
Note
• If an error code or warning message appears on the screen in
step3, see “List of messages after Auto Calibration measurements”
(page 18).
Tips
• You can also perform automatic calibration by pressing the AUTO
CAL button on the remote control. If you use the AUTO CAL button,
the following restrictions apply to the operation:
Prior settings relating to the Auto Calibration will be skipped.
You can only use the display panel for the operation.
• The Auto Calibration function will be canceled if you perform the
following during the measurement process:
Turn the receiver on or off.
Press the input buttons on the remote control or on the receiver.
Press .
Press SPEAKERS on the receiver.
Press HDMI OUTPUT.
Press AMP MENU.
Press HOME.
Press AUTO CAL.
Change the volume level.
List of messages after Auto Calibration
measurements
Code 31:
Front speakers are not selected properly. Select the front
speakers using SPEAKERS, and then perform Auto
Calibration again.
Code 32, Code 33:
Speakers were not detected or not connected properly.
None of the front speakers are connected or only one front
speaker is connected.
Either the surround left or surround right speaker is not
connected.
A surround back speaker is connected only to the SPEAKERS
SURROUND BACK/HEIGHT (FRONT B/BI-AMP/ZONE 2) R
terminal. If connecting only one surround back speaker,
connect it to the SPEAKERS SURROUND BACK/HEIGHT
(FRONT B/BI-AMP/ZONE 2) L terminal.
Either the Height1 left or Height1 right speaker is not
connected (for STR-ZA3100ES/STR-ZA2100ES).
Either the Height2 left or Height2 right speaker is not
connected (for STR-ZA3100ES/STR-ZA2100ES).
Either the Height left or Height right speaker is not
connected (for STR-ZA1100ES).
The calibration microphone is not connected. Make sure that
the calibration microphone is connected properly, and then
perform Auto Calibration again.
If the calibration microphone is connected properly but the
error code still appears, the calibration microphone cable
may be damaged.
Code 34:
Speakers are not placed in the proper position. Speakers or
the calibration microphone on the right or left may be
placed wrongly. See the supplied Startup Guide and check
the speaker position.
Code 35:
The measurement result is not match to the speaker
pattern you set. See the Help Guide and change the setting
to fit the actual speaker pattern.
Warning 40:
The measurement process has been completed and a high
noise level has been detected. You may be able to achieve
better results if you try the process again in a quiet
environment.
Warning 41, Warning 42:
The input from the calibration microphone is too large.
The distance between the speaker and the calibration
microphone may be too small. Set them further apart and
perform the measurement again.
Warning 43:
The distance and position of a subwoofer cannot be
detected. This may be caused by noise. Try performing the
measurement in a quiet environment.
Warning 44:
Measurement has been completed. However the speakers
are not placed in the proper position with respect to each
other. See the supplied Startup Guide and check the
relative positions of the speakers.
NO WARNING:
There is no warning information.
Saving/loading settings of the receiver
You can save the settings to a USB flash drive and restore
the saved settings to the receiver or to another receiver of
the same model.
Saving Loading
To save the settings
Insert a USB flash drive to the USB port on the front panel of
the receiver.
Select [Setup] - [Install Setup] - [Save/Load] - [Save] from the
home menu.
To load the settings
Insert to the USB port on the front panel of the receiver a
USB flash drive on which the settings are saved.
Select [Setup] - [Install Setup] - [Save/Load] - [Load] from the
home menu.
19
US
Settings
Linking with a Hi-Fi music system
This receiver can switch its power and input automatically by
linking with playback operation of the Hi-Fi music system.
Configure settings to enable the receiver to operate linked
with a Hi-Fi System device.
1 Select [Setup] - [Network Setup] - [Music
Connect] from the home.
2 Select the setting you want.
Each of the following settings can be selected on both
Device 1 and Device 2.
Connected Device: Select the connected device to
enable the function.
Input for Music Connect1 or 2: Select the input to link
with.
Preset Volume: Preset the volume level.
Output Zone: Select the zone to which you want to
output sound.
3 Start playback on the player device.
The receiver will be turned on and the input will be
switched automatically.
To disable Music Connect
Select [Setup] - [Network Setup] - [Music Connect] -
[Connected Device] - [Remove Connected Device] from the
home menu.
Notes
• The Music Connect feature can be linked only with the power
source and input of the main zone or Zone 2. This feature does not
link with Zone 3.
• The link feature of Music Connect may not work correctly
depending on factors such as the specifications of the connected
device.
• We recommend that you set [Network Standby] to [On] to activate
the feature for linking with Music Connect even if the receiver is in
standby mode.
Mixing separate audio/video inputs (Last
video mode)
The receiver can continuously output the input video image
used most recently when an audio-only input source is
selected.
1 Connect the desired background music source to
an input by analog, optical, or coaxial cable. Or
use the built-in tuner.
2 Set the input to the following in the Input Setup
menu.
HDMI: [None]
Component: [None]
Composite: [---]
Audio: The input connected to the source.
When using the built-in tuner, set the screen mode to
[Simple] using the options menu in [FM/AM Display].
Example
Press SAT/CATV followed by TUNER to listen to sound from
the built-in tuner while watching a video source connected
to SAT/CATV.
The audio output changes to that of the tuner source while
SAT/CATV video output is retained.
Setting the in-ceiling speaker mode
Sony has developed a new special sound mode for CI
installation. This feature will virtually relocate the front and
center in-ceiling speakers down to around the screen. That
way, the customer will hear the actors’ voices coming from
the screen instead of the ceiling. This mode also makes
music sound more natural in a room with in-ceiling speakers.
1 Perform Auto Calibration.
2 Select [Setup] - [Audio Setup] - [In-Ceiling
Speaker Mode] - [Front & Center] or [Front] from
the home menu.
Notes
• This mode is not available when [Pure Direct] is set to [On].
• This mode will be disabled in a speaker pattern with Dolby Atmos
enabled speakers.
Tips
• You can select on/off for each input in Input Setup menu.
• You can also select [In-Ceiling Speaker Mode] in [Sound Effects]
from the home menu.
• You can also switch the function on/off by pressing IN-CEILING SP
on the remote control or the receiver.
• To obtain optimal effects in the listening environment, configure
the [Ceiling Height] setting and perform Auto Calibration.
Setting HDMI signal formats
When you use high bandwidth video formats such as
4K/60p YCbCr 4:4:4/YCbCr 4:2:2/RGB4:4:4 or 4K/60p YCbCr
4:2:0 Deep Color (Deep Colour) (10 bit or 12 bit), be sure to
set [HDMI Signal Format].
1 Select [Setup] - [HDMI Setup] - [HDMI Signal
Format] from the home menu.
2 Select the HDMI input you want to apply the
setting.
3 Select [Enhanced format].
20
US
Notes
• For details on the high bandwidth video format, refer to the Help
Guide.
• When [Enhanced format] is selected, we recommend to use a
Premium High Speed HDMI Cable with Ethernet, which can support
bandwidth up to 18 Gbps.
• When [Enhanced format] is selected, some devices (cable box or
satellite box, Blu-ray Disc player, and DVD player) may not work. In
this case, select [Standard format].
• If your TV has similar menu for high bandwidth video format,
check the setting on the TV menu when you select [Enhanced
format] on this receiver. For details on the TV menu setting, refer to
the operating instructions of the TV.
Updating the software via the network
You can update the receiver software via the network.
Connect the receiver to the Internet beforehand, and then
make sure [Internet Connection] is displayed as [OK] in the
[Network Information] menu.
1 Select [Setup] - [System Setup] from the home
menu.
2 Select [Network Update].
3 Follow the instructions on the TV screen.
[UPDATING…XXX%] will be displayed on the front
display. The receiver will automatically reboot after the
update completes.
Updating the software with a USB flash drive
Make sure to perform the following steps when a software
update is delivered.
You can download the update software from the following
website.
http://esupport.sony.com/
Saving
New software
Updating
1 Copy the file for updating to the top level
directory (just under the root directory) of the
USB flash drive (FAT16 or FAT32 with more than
100MB of free space).
2 Turn the receiver on.
3 Insert the USB flash drive into the USB port on
the front panel of the receiver.
4 Select [Setup] - [System Setup] - [USB Update]
from the home menu.
[UPDATING…XXX%] will be displayed on the front
display. The receiver will automatically reboot after the
update completes.
Note
• It takes up to 100minutes for the update to complete.
Setting up through a web browser
The receiver provides a web browser interface for
configuring settings.
The PING feature is useful for checking your IP address
quickly.
Open a web browser on your computer or mobile
device on the same network with the receiver, and
then access
http://[receiver’s IP address]/
Using the PING button
The receiver provides the following functions simply by
pressing the PING button on the front panel of the receiver.
The receiver sends specific UDP multicast or broadcast
packets to establish a network connection.
Protocol Protocol owner
SDDP Control4
The receiver displays its IP information on the front display
as follows.
Information
1 IP address
2 MAC address
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Sony STR-ZA1100ES User manual

Category
AV receivers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI