Sony CAS-1 Owner's manual

Brand: Sony

Model: CAS-1

Category: Bluetooth music receivers

Type: Owner's manual

CAS-1

Precautions / Troubleshooting

Précautions / Dépannage

Compact Audio System

Owner’s Record

The model and serial numbers are located on the bottom of the unit.

Record the serial numbers in the space provided below. Refer to them

whenever you call upon your Sony dealer regarding this product.

Model No. CAS-1

Serial No.

To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

Do not install this equipment in a confined space such as a bookshelf or

similar unit.

To reduce the risk of fire, do not cover the ventilation opening of the

appliance with newspapers, tablecloths, curtains, etc.

Do not expose the appliance to naked flame sources (for example, lighted

candles).

To reduce the risk of fire or electric shock, do not expose this appliance to

dripping or splashing, and do not place objects filled with liquids, such as

vases, on the appliance.

The unit is not disconnected from the mains as long as it is connected to

the AC outlet, even if the unit itself has been turned off.

As the main plug is used to disconnect the unit from the mains, connect

the unit to an easily accessible AC outlet. Should you notice an abnormality

in the unit, disconnect the main plug from the AC outlet immediately.

As the main plug of AC power adaptor is used to disconnect the AC power

adaptor from the mains, connect it to an easily accessible AC outlet. Should

you notice an abnormality in it, disconnect it from the AC outlet

immediately.

Do not expose batteries or appliances with battery-installed to excessive

heat, such as sunshine and fire.

Indoor use only.

For the unit:

The nameplate and the date of manufacture marking are located on the

bottom.

For the AC adapter:

Labels for AC adapter Model No. and Serial No. are located at the bottom

of AC adapter.

For the speakers:

The nameplate is located on the bottom of the speaker.

The following FCC/IC statement applies only to the version of this model

manufactured for sale in the USA and Canada. Other versions may not

comply with FCC/IC technical regulations.

This equipment complies with FCC/IC radiation exposure limits set forth for

an uncontrolled environment and meets the FCC radio frequency (RF)

Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure

rules. This equipment has very low levels of RF energy that is deemed to

comply without maximum permissive exposure evaluation (MPE).

WARNING

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD

The remote control supplied with this product contains a coin/button cell

battery. If the coin/button cell battery is swallowed, it can cause severe

internal burns in just 2 hours and can lead to death.

Keep new and used batteries away from children. If the battery

compartment does not close securely, stop using the product and keep it

away from children.

If you think batteries might have been swallowed or placed inside any

part of the body, seek immediate medical attention.

For the customers in the U.S.A

This symbol is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric

shock to persons.

This symbol is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

For the State of California, U.S.A. only

Perchlorate Material: special handling may apply.

See

www.dtsc.ca.gov/hazardouswaste/perchlorate

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at

plugs, convenience receptacles, and the point where they exit from the

apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use

caution when moving the cart/apparatus combination to avoid injury

from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long

periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power-

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

NOTE:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

WARNING

continued

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

If you have any questions about this product, you may call:

Sony Customer Information Center 1-800-222-SONY (7669) or

http://www.sony.com/.

The number below is for the FCC related matters only.

Regulatory Information

CAUTION

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

This equipment must not be co-located or operated in conjunction with

any other antenna or transmitter.

For the customers in Canada

This device complies with Industry Canada’s licence-exempt RSSs.

Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that

may cause undesired operation of the device.

 Windows Media is either a registered trademark or trademark of Microsoft

Corporation in the United States and/or other countries.

 This product is protected by certain intellectual property rights of

Microsoft Corporation. Use or distribution of such technology outside of

this product is prohibited without a license from Microsoft or an

authorized Microsoft subsidiary.

 Apple, iPhone, iPod, iPod touch, macOS, Mac and OS X are trademarks of

Apple Inc., registered in the U.S. and other countries.

App Store is a service mark of Apple Inc., registered in the U.S. and other

countries.

 Use of the Made for Apple badge means that an accessory has been

designed to connect specifically to the Apple product(s) identified in the

badge, and has been certified by the developer to meet Apple

performance standards. Apple is not responsible for the operation of this

device or its compliance with safety and regulatory standards.

 MPEG Layer-3 audio coding technology and patents licensed from

Fraunhofer IIS and Thomson.

 The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in

the United States and in other countries.

 The BLUETOOTH® word mark and logos are registered trademarks owned

by BLUETOOTH SIG, Inc. and any use of such marks by Sony Corporation

is under license.

 LDAC™ and LDAC logo are trademarks of Sony Corporation.

 Android and Google Play are trademarks of Google LLC.

 Other trademarks and trade names are those of their respective owners.

Declaration of Conformity

Trade Name: SONY

Model No.: TA-CA1

Responsible Party: Sony Electronics Inc.

Address: 16535 Via Esprillo, San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Copyrights

WARNING ................................................................................2

Copyrights ............................................................................. 4

Precautions ............................................................................ 6

Changing the battery of the remote control .........................7

Turning off BLUETOOTH ........................................................ 8

Resetting the unit .................................................................. 8

Troubleshooting .................................................................... 9

Specifications ....................................................................... 12

On BLUETOOTH® Communication .......................................14

End users license agreement ...............................................15

Table of contents

Refer to the supplied “Operating Instructions” for

instructions on setup and operations.

Precautions

On safety

Should any solid object or liquid fall into the cabinet, unplug the unit and

have it checked by qualified personnel before operating it any further.

On power sources

 Before operating the system, check that the operating voltage is identical

with your local power supply.

The operating voltage is indicated on the nameplate on the bottom of the

unit.

 The unit is not disconnected from the AC power source (mains) as long as

it is connected to the wall outlet, even if the unit itself has been turned off.

 If you are not going to use the system for a long time, be sure to

disconnect the unit from the wall outlet. To disconnect the AC cord, grasp

the plug itself; never pull the cord.

 The AC cord must be changed only at a qualified service shop.

On placement

 Place the system in a location with adequate ventilation to prevent heat

buildup and prolong the life of the system.

 Do not place the system near heat sources, or in a place subject to direct

sunlight, excessive dust, or mechanical shock.

 Do not place anything on top of the cabinet that might cause

malfunctions.

 Use caution when placing the system on surfaces that have been specially

treated (with wax, oil, polish, etc.) as staining or discoloration of the

surface may result.

On operation

Before connecting other equipment, be sure to turn off and unplug the

unit.

On cleaning

Clean this system with a soft cloth slightly moistened with a mild detergent

solution. Do not use any type of abrasive pads, scouring powder, or

solvents, such as thinner, benzine, or alcohol.

On supplied accessories

 The supplied speaker bases are very heavy, because they are made of

iron.

Be careful when you handle them.

 Some of the supplied accessories, such as the spikes, have the potential

risk of being accidentally ingested by children. Put the accessories out of

reach of children.

If you have any questions or problems concerning your system, please

consult your nearest Sony dealer.

Changing the battery of the remote control

The working distance of the remote shortens as the battery becomes

exhausted. When the remote no longer operates the unit, replace the

battery with a new CR2032 lithium battery (not supplied).

1 Push and hold  at the rear of the remote, then pull out the

battery holder in the direction of the arrow.

2 Replace the battery with the “+” facing up, then insert the

battery holder into the slot.

Wipe the battery with a dry cloth to assure a good contact.

Do not hold the battery with metallic tweezers, otherwise a short-circuit

may occur.

Use of batteries other than the CR2032 may cause a fire or explosion.



Notes

+ facing up

Battery holder

Turning off BLUETOOTH

Press the  (on/standby) button of the unit to turn on the

unit.

2 Press and hold the input select button and (BLUETOOTH)

PAIRING button of the unit simultaneously for more than 4

seconds.

The LED status indicators flash from right to left when BLUETOOTH

turns off.

To turn on BLUETOOTH, operate step 2 again. The LED status

indicators flash from left to right.

Hint

If you disconnect the AC cord from the wall outlet when the unit is turned

off, BLUETOOTH turns on automatically when the unit turns on again.

If you turn off BLUETOOTH, all the BLUETOOTH and NFC features become

unavailable when the unit is turned on, enters standby mode or enters

BLUETOOTH standby mode.

Resetting the unit

If the unit still does not operate properly even after checking the

troubleshooting, or when you fail setting, reset the unit.

1 Press the  (on/standby) button of the unit to turn off the

unit.

2 Press and hold the  (on/standby) button of the unit for

over 10 seconds while the unit is turned off.

After the LEDs above the volume control quickly flash, the unit

enters the standby mode automatically, and all settings of the unit

will return to the factory defaults as follows:

 All the BLUETOOTH pairing information are deleted.

 DIMMER: Bright

 Low Volume Mode: On

 DSEE HX: Auto

 BLUETOOTH LDAC: On

 BLUETOOTH Standby: Off

 MUTING: Off

 INPUT: BLUETOOTH

If you initialize the unit, BLUETOOTH connections with an iPhone/iPod may

not work. In this case, delete the unit from the paired device list of your

iPhone/iPod, and then perform pairing again.

Note

Troubleshooting

If you experience any of the following difficulties while using the system, use

this troubleshooting guide to help remedy the problem before requesting

repairs. Should any problem persist, consult your nearest Sony dealer.

General

All the Input LED indicators and the LEDs above the volume control

are flashing at the same time.

 The protection feature is activated. Disconnect the AC cord and

check the items below.

 Check the connection with the connected speakers and turn on

the unit (Refer to “Set up” of the Operating Instructions).

 Make sure that the ventilations of the unit are not covered and

turn on the unit after a while.

 When the unit is using the USB-A connection, remove the device

connected to the A (USB-A) port and turn on the unit. If the unit

operates properly, the current of the connected USB device is over

the maximum output current of the unit 1A, or the USB device may

have an abnormality.

 If you listen to the sound at volumes high enough to distort the

sound, the protection feature might be activated. If the protection

feature is activated, disconnect the AC cord from the wall outlet

and reconnect it, then turn on the unit and turn down the volume.

The LED above the volume control flashes for a while even after

turning off the unit.

 This is not a malfunction. The LED flashes for about 30 seconds after

pressing the  (on/standby) button, and the unit enters the

standby mode when the LED turns off.

The unit does not turn on.

 Insert the AC adapter to the DC IN jack of the unit until it clicks.

 Insert the AC cord to the AC adapter firmly.

The unit does not turn on by pressing the  (on/standby) button

soon after connecting the AC adapter.

 The unit is checking its internal status. Wait for a few seconds and

press the  (on/standby) button.

The unit turns off automatically.

 Check the AUTO STANDBY switch on the rear side of the unit. If it is

set to “ON,” the Auto standby function is activated. When set to ON,

the unit enters standby mode automatically if there is no playback

or operation for 15 minutes (Refer to “Part Names” of the Operating

Instructions).

The unit turns off automatically and unexpectedly, and the central

LED above the volume control lights up in blue.

 The BLUETOOTH standby mode is activated. Check the AUTO

STANDBY switch on the rear side of the unit. If both the BLUETOOTH

standby function and Auto standby function are activated, and

operations or music playback stops for over 15 minutes, the unit

turns off and enters the BLUETOOTH standby mode automatically

(Refer to “Part Names” of the Operating Instructions).

The last settings have not been retained.

 If the AC cord is disconnected from a mains or the AC adaptor is

disconnected from the DC IN jack while the unit turns on, the last

settings are not retained. Make sure that the unit is turned off when

you pull out the AC cord from the mains or pull out the AC adaptor

from the DC IN jack.

There is no sound from connected speakers or headphones.

 Make sure that the volume is not at the lowest setting.

 When using speakers, make sure the speaker cords are connected

correctly to both speakers. Sound is not output if one of the

connections is incomplete (Refer to “Set up” of the Operating

Instructions).

 When using headphones, make sure to connect the headphone

plug firmly to the  (headphone) jack of the unit.

 The sound is not output from the connected speakers when

headphones are connected to the unit. Pull out the headphone

plug from the  (headphone) jack.

Left and right sound balance is unclear or reversed.

 Position the speakers symmetrically.

 Make sure that speaker cords L/R and +/– are connected correctly.

continued

Muting is activated.

 Press the MUTING button on the remote. Or, turn the volume up by

using the VOL +/– buttons on the remote or the volume control on

the main unit.

Severe hum or noise occurs.

 Make sure to check the connection with the speakers (Refer to “Set

up” of the Operating Instructions).

BLUETOOTH

Pairing (device registration) failed, or the unit cannot establish

BLUETOOTH connections with a Walkman/smartphone/iPhone

while the SongPal is set.

 When using a Walkman or a smartphone with the NFC function,

keep touching it on the N-Mark of the unit until the BLUETOOTH

input LED stops flashing and remains lit.

 When you cannot establish a BLUETOOTH connection by one touch

(NFC), press the (BLUETOOTH) PAIRING button on the rear side of

the unit or the PAIRING button on the remote, and pair the device

with the unit (Refer to “Playback” of the Operating Instructions).

Cannot pair a BLUETOOTH device with the unit.

 When using a Walkman or a smartphone with the NFC function,

touch the device on the N-Mark of the unit and they will be paired

(Refer to “Playback” of the Operating Instructions).

 Check that the unit is not effected by a wireless LAN, other 2.4 GHz

wireless equipment, or a microwave oven. When there is

equipment that generates electromagnetic waves, use them away

from the unit.

Cannot establish the connection.

 Place the BLUETOOTH device to be connected within one meter of

the unit.

Cannot establish a BLUETOOTH connection by one touch (NFC).

 Turn on the NFC function of the Walkman or the smartphone.

 Touch the N-Mark of the Walkman or the smartphone on the N-

Mark of the unit. If the device does not respond even though it is

touched to the unit, move it slowly to the front, rear, left and right.

Once it responds, follow the on screen instructions of the device

and finish establishing the connection.

 If the smartphone has a case, the connection may succeed when

the case is removed.

The unit turns off automatically after it is turned on by one touch

(NFC) from the power off state.

 The unit turns off automatically when the BLUETOOTH connection is

not completed within 1 minute after turning on the unit by one

touch (NFC).

There is distorted sound, noise, or skipping.

 Place the connected device within one meter of the unit.

 If the connected device has the setting for playback quality for a

BLUETOOTH connection, set the setting as the connection priority.

 Press the LDAC button on the remote to turn off the LDAC function.

Sound of the connected PC is not output.

 Make sure that the sound output of the PC is set to BLUETOOTH.

 Make sure that the BLUETOOTH connection between the PC and the

unit is established.

 Pair the PC and the unit again.

USB-A

The USB device is not recognized.

 The USB device is not recognized until the USB-A input LED stops

flashing and remains lit.

 iPhone/iPod cannot be played back via the USB-A connection.

When you use iPhone/iPod with the unit, a BLUETOOTH connection

is necessary.

Contents in folders of a USB device are not displayed in SongPal.

 Contents of folders after the 10th level of a folder are not displayed.

The unit can display the contents up to the 10th level of a folder

(including the “ROOT” folder). The maximum number of folders and

files on the USB device that can be displayed with this unit is 998.

Sound is not output immediately after the unit turns on.

 It takes time for sound to output. Wait until the USB-A input LED

stops flashing and remains lit.

It takes time until the unit is available for a playback.

 It takes time for sound to output. Wait until the USB-A input LED

stops flashing and remains lit.

The USB-A input LED keeps flashing and does not remain lit.

 A non-compatible device is connected to the A (USB-A) port. The

LED remains lit after removing the device.

USB-B

The USB device is not recognized.

 Turn off the unit and remove the USB device, and turn on the unit

again. Then, reconnect the USB device.

 Connect a compatible USB device.

 The USB device might not be working properly. Refer to the

operating instructions of the USB device.

There is no sound, or the sound is output from the speakers of the

connected PC.

 Check that the sound format of the file is the supported one

(page 13).

 If you connect the PC to the B (USB-B) port on the rear side of the

unit, make sure the dedicated driver is installed to the PC.

 Check that the sound device setting of your computer is set to “Sony

Audio.” If not, set it correctly.

The following setting procedures are examples. The procedures

and displays may change depending on the usage environment of

your computer.

 For Windows 7/Windows Vista:

Click the [Start] menu, select [Control Panel], [Hardware and

Sound], [Sound], [Playback] tab, select [Sony Audio] for the

playback device, then click [Set default].

 For Windows 8/8.1:

Display the charm bar on the right side of the desktop and

select [Settings], [Control Panel], [Hardware and Sound],

[Sound], [Playback] tab, select [Sony Audio] for the playback

device, then click [Set default].

 For Macintosh:

Click the [Apple] menu, select [System Preferences], [Sound],

[Output] tab, then select [Sony Audio] for [Select a device for

sound output].

Sound skips.

 Depending on the actions of other active software, the sound might

skip.

The sound of the music playback software of the PC is not output.

 Turn up the volume of the music playback software.

 Deactivate the muting function by pressing the MUTING button or

VOL +/– buttons on the remote.

 Do not activate multiple music playback software.

There is noise or distorted sound on the music playback software

of the PC.

 Do not activate multiple music playback software.

Cannot play back the songs (files) of multi channels.

 Only 2-channel songs (files) are available.

Remote

Cannot operate the unit with the remote.

 Pull out the insulation sheet from the remote when you use it for the

first time (Refer to “What’s in the box” of the Operating Instructions).

 Point the remote to the remote sensor (the circuit of the  (on/

standby) button) of the unit.

 Remove any obstacles in the path between the remote and the unit.

 Replace the battery in the remote with a new one (page 7).

Specifications

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION:

With 5 ohm loads, both channels driven, from 20 - 20,000 Hz; rated 20

watts per channel minimum RMS power, with no more than 10% total

harmonic distortion from 250 milliwatts to rated output.

Amplifier section

Reference Power Output

24 W + 24 W (5 , 1 kHz, THD 10%)

Rated Power Output

20 W + 20 W (5 , 20 Hz - 20 kHz, THD 1%)

Speaker impedance match

5 - 16

Frequency response

10 Hz - 40 kHz (+0 dB, –3 dB) (5 , B (USB-B) input)

BLUETOOTH section

Output

BLUETOOTH Specification Power Class 2

Maximum communication range

Line of sight approx. 10 m*

Available pairing

Up to 9 devices

When the unit has been already been paired with 9 BLUETOOTH

devices and you attempt to pair with an additional device, the pairing

information of the oldest connected device is deleted automatically.

Radio frequency

2.4 GHz band (2.4000 GHz - 2.4835 GHz)

Communication System

BLUETOOTH Specification Version 3.0

Compatible BLUETOOTH Profiles*

A2DP (Advanced Audio Distribution Profile)

AVRCP (Audio Video Remote Control Profile)

Supported codec*

SBC*

AAC*

LDAC*

Supported content protection method

SCMS-T method

Transmission bandwidth (A2DP)

20 Hz - 20,000 Hz (with 44.1 kHz sampling)

20 Hz - 40,000 Hz (with LDAC 96 kHz sampling, 990 kbps)

The actual range will vary depending on factors such as obstacles

between devices, magnetic fields around a microwave oven, static

electricity, reception sensitivity, aerial’s performance, operating system,

software application, etc.

BLUETOOTH standard profiles indicate the purpose of BLUETOOTH

communication between devices.

Codec: Audio signal compression and conversion format

Subband Codec

Advanced Audio Coding

LDAC is an audio coding technology developed by Sony that enables

the transmission of High-Resolution (Hi-Res) Audio content, even over

a BLUETOOTH connection. Unlike other BLUETOOTH compatible coding

technologies such as SBC, it operates without any down-conversion of

the Hi-Res Audio content*

, and allows approximately three times more

data*

than those other technologies to be transmitted over a

BLUETOOTH wireless network with unprecedented sound quality, by

means of efficient coding and optimized packetization.

Excluding DSD format contents

In comparison with SBC (Subband Coding) when the bitrate of 990 kbps

(96/48 kHz) or 909 kbps (88.2/44.1 kHz) is selected.

USB port section

A (USB-A) port

You can connect a USB flash drive and Walkman that is compatible with

this unit.

Compact Audio Amplifier (TA-CA1)

Supported format*

MP3: 16/22.05/24/32/44.1/48 kHz, 32 - 320 kbps (CBR/VBR)

AAC: 16/22.05/24/32/44.1/48/88.2/96 kHz, 40 - 320 kbps (CBR/VBR)

WMA: 32/44.1/48 kHz, 16 - 320 kbps (CBR/VBR)

WAV: 16/22.05/24/32/44.1/48/88.2/96/176.4/192 kHz (16/24 bit)

AIFF: 32/44.1/48/88.2/96/176.4/192 kHz (16/24 bit)

FLAC: 44.1/48/88.2/96/176.4/192 kHz (16/24 bit)

ALAC: 44.1/48/88.2/96/176.4/192 kHz (16/24 bit)

DSD (DSF/DSDIFF): 2.8 MHz (1 bit)

Transfer speed

High-speed

Supported USB device

Mass Storage Class (MSC)

Maximum output current

1A MAX

Depending on the device, the charge current might be limited to

500 mA.

Supported file system

FAT

FAT32

exFAT

B (USB-B) port

You can connect a compatible device such as a PC, etc., to this unit using

the supplied USB cable.

Supported format*

PCM: 44.1/48/88.2/96/176.4/192 kHz (16/24/32 bit)

DSD (DSF/DSDIFF): 2.8 MHz (1 bit)

Compatibility with all encoding/writing software, recording devices and

recording media cannot be guaranteed.

Headphones section

250 mW + 250 mW (8 Ω, THD 1%)

180 mW + 180 mW (32 Ω, THD 1%)

35 mW + 35 mW (300 Ω, THD 1%)

General

Power requirements

DC 19.5 V (using the supplied AC adaptor connected to AC 100 V-240

V, 50 Hz/60 Hz power supply)

Power consumption (using the supplied AC adaptor)

29 W

Power consumption (during standby mode)

0.5 W (When BLUETOOTH standby mode is set to off.)

2 W (When BLUETOOTH standby mode is set to on.)

Dimensions (w/h/d) (including projecting parts)

Approx. 55 mm × 178 mm × 210 mm (2

inches × 7

inches ×

inches)

Mass

Approx. 1.3 kg (2 Ib 13

oz)

Speaker system

2 way, 2 drivers speaker system, Bass reflex

Speakers unit

Tweeter: 14 mm (

inches), soft dome type × 1

Woofer: 62 mm (2

inches), cone type × 1

Rated impedance

5 

Dimensions (w/h/d) (including projecting parts and controls)

Approx. 95 mm × 178 mm × 172 mm (3

inches × 7

inches ×

inches)

Mass

Approx. 1.5 kg (3 Ib 4

oz)

Supplied accessories

AC adapter (1)

AC cord (1)

USB cable (1)

Speaker cord (2)

Spike (Large) (4)

Speaker base (2)

Stand (1)

Remote control (1)

Operating Instructions (1)

Precautions / Troubleshooting (this document) (1)

Design and specifications are subject to change without notice.

Speaker System (SS-HW5)

General

continued

Compatible iPhone/iPod models

As of June 2015

Sony cannot accept responsibility in the event that data recorded to

iPhone/iPod is lost or damaged when using your iPhone/iPod connected

to this unit.

On BLUETOOTH® Communication

BLUETOOTH wireless technology is a short-range wireless technology that

enables wireless data communication between digital devices, such as a

computer and digital camera. BLUETOOTH wireless technology operates

within a range of about 10m.

Connecting two devices as necessary is common, but some devices can be

connected to multiple devices at the same time.

You do not need to use a cable for connection, nor is it necessary for the

devices to face one another, such is the case with infrared technology. For

example, you can use such a device in a bag or pocket.

BLUETOOTH standard is an international standard supported by thousands

of companies all over the world, and employed by various companies

worldwide.

Maximum communication range

Maximum communication range may shorten under the following

conditions.

 There is an obstacle such as a person, metal, or wall between the

system and BLUETOOTH device.

 A wireless LAN device is in use near the system.

 A microwave oven is in use near the system.

 A device that generates electromagnetic radiation is in use near the

system.

Interference from other devices

Because BLUETOOTH devices and wireless LAN (IEEE802.11b/g/n) use the

same frequency, microwave interference may occur and resulting in

communication speed deterioration, noise, or invalid connection if the

system is used near a wireless LAN device. In such a case, perform the

following.

 Use the system at least 10 m away from the wireless LAN device.

 If the system is used within 10 m of a wireless LAN device, turn off the

wireless LAN device.

Compatible models BLUETOOTH

iPhone 6 

iPhone 6 Plus 

iPhone 5s 

iPhone 5c 

iPhone 5 

iPhone 4s 

iPhone 4 

iPod touch (5th generation) 

Note

What is BLUETOOTH wireless technology?

Interference to other devices

Microwaves emitting from a BLUETOOTH device may affect the operation

of electronic medical devices. Turn off the system and other BLUETOOTH

devices in the following locations, as it may cause an accident.

 where inflammable gas is present, in a hospital, train, airplane, or a gas

station

 near automatic doors or a fire alarm

To be able to use the BLUETOOTH function, the BLUETOOTH device to be

connected requires the same profile as the system’s.

Note also that even if the same profile exists, devices may vary in function

depending on their specifications.

Due to the characteristic of BLUETOOTH wireless technology, the sound

played on the system is slightly delayed from the sound played on the

BLUETOOTH device during talking on the telephone or listening to the

music.

This system supports security capabilities that comply with the

BLUETOOTH standard to provide a secure connection when the

BLUETOOTH wireless technology is used, but security may not be enough

depending on the setting. Be careful when communicating using

BLUETOOTH wireless technology.

We do not take any responsibility for the leakage of information during

BLUETOOTH communication.

A device featuring the BLUETOOTH function is required to conform to the

BLUETOOTH standard specified by Bluetooth SIG, and be authenticated.

Even if the connected device conforms to the above mentioned

BLUETOOTH standard, some devices may not be connected or work

correctly, depending on the features or specifications of the device.

Noise or sound skips may occur depending on the BLUETOOTH device

connected with the system, the communication environment or the

usage environment.

End users license agreement

Notes on the License

This product contains software that Sony uses under a licensing

agreement with the owner of its copyright. We are obligated to

announce the contents of the agreement to customers under

requirement by the owner of copyright for the software. The content

of the license is provided on the web page. Please read the content of

the following URL.

URL: http://oss.sony.net/Licence/CAS-1

Notice on GNU GPL/LGPL applied software

This product contains software that is subject to the following GNU

General Public License (hereinafter referred to as “GPL”) or GNU Lesser

General Public License (hereinafter referred to as “LGPL”). These

establish that customers have the right to acquire, modify, and

redistribute the source code of said software in accordance with the

terms of the GPL or LGPL supplied. The source code for the above-

listed software is available on the Web.

To download, please access the following URL then select the model

name “CAS-1”.

URL: http://oss.sony.net/Products/Linux/

Please note that Sony cannot answer or respond to any inquiries

regarding the content of the source code.

Enregistrement du propriétaire

Les numéros de modèle et de série se trouvent sur la partie inférieure de

l’appareil. Indiquez ces numéros dans l’espace prévu à cet effet ci-

dessous. Vous devrez vous y référer lors d’un appel à votre détaillant Sony

au sujet de ce produit.

N° de modèle CAS-1

N° de série

Pour réduire les risques d’incendie ou d’électrocution,

gardez cet appareil à l’abri de la pluie et de l’humidité.

N’installez pas cet appareil dans un endroit confiné, comme une étagère

ou un meuble semblable.

Pour réduire les risques d’incendie, ne couvrez pas l’ouverture d’aération

de l’appareil avec des papiers journaux, des nappes, des rideaux, etc.

N’exposez pas l’appareil à des sources à flamme nue (par exemple, des

chandelles allumées).

Pour réduire le risque d’incendie ou d’électrocution, n’exposez pas cet

appareil à des éclaboussures ou des gouttes d’eau et ne posez pas dessus

des objets remplis de liquides, notamment des vases.

L’appareil n’est pas débranché de la prise électrique aussi longtemps qu’il

est raccordé à la prise CA, même s’il est éteint.

La fiche principale étant utilisée pour déconnecter l’appareil de la prise

électrique, connectez l’appareil à une prise CA facilement accessible. Si

vous constatez que l’appareil ne fonctionne pas normalement,

déconnectez immédiatement la fiche principale de la prise CA.

Comme la fiche principale de l’adaptateur d’alimentation CA est utilisée

pour déconnecter l’adaptateur d’alimentation CA de la prise électrique,

connectez-la à une prise CA facilement accessible. Si vous constatez que

l’appareil ne fonctionne pas normalement, déconnectez-le

immédiatement de la prise CA.

N’exposez pas les piles ou un appareil contenant des piles à une chaleur

excessive, notamment aux rayons directs du soleil ou à des flammes.

Utilisation à l’intérieur seulement.

Pour l’appareil :

La plaque signalétique et l’inscription de la date de fabrication sont situées

sur la partie inférieure.

Pour l’adaptateur CA :

Les étiquettes indiquant le numéro de modèle et le numéro de série de

l’adaptateur CA se trouvent sur la partie inférieure de l’adaptateur CA.

Pour les enceintes :

La plaque signalétique est fixée sur la partie inférieure de l’enceinte.

La déclaration suivante de la FCC/IC s’applique uniquement à la version de

ce modèle fabriquée pour la vente aux États-Unis et au Canada. Il se

pourrait que les autres versions ne soient pas conformes aux

réglementations techniques de la FCC/IC.

Cet équipement est conforme aux limites d’exposition aux rayonnements

énoncées pour un environnement non contrôlé et respecte les règles les

radioélectriques (RF) de la FCC lignes directrices d'exposition et

d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet

équipement émet une énergie RF très faible qui est considérée comme

conforme sans évaluation de l’exposition maximale autorisée.

AVERTISSEMENT

ATTENTION

Danger d’explosion si la pile n’est pas remplacée correctement.

Remplacez la pile uniquement par une pile de type identique ou

équivalent.

NE PAS INGÉRER LA PILE, RISQUE DE BRÛLURE CHIMIQUE

La télécommande fournie avec ce produit contient une pile de dimension

monnaie/bouton. Si cette pile est ingérée, elle est susceptible de causer

des brûlures internes graves en seulement 2 heures et entraîner la mort.

Garder les piles neuves et usées hors de portée des enfants. Si le

compartiment de la pile ne se ferme pas de manière sécuritaire, cesser

d’utiliser le produit et le garder hors de portée des enfants.

Si vous pensez que des piles ont été ingérées ou insérées dans toute

partie du corps, consulter immédiatement un médecin.

Pour les clients résidant aux États-Unis

Ce symbole est destiné à renseigner l’utilisateur sur la présence à

l’intérieur du boîtier de l’appareil d’une « tension dangereuse »

non isolée et suffisamment puissante pour présenter un risque

d’électrocution.

Ce symbole est destiné à renseigner l’utilisateur sur la présence

d’importantes instructions d’utilisation et d’entretien (service)

dans les documents qui accompagnent l’appareil.

Uniquement pour l’État de la Californie, États-Unis

Matériaux de perchlorate : une manutention spéciale peut s’appliquer.

Voir

www.dtsc.ca.gov/hazardouswaste/perchlorate

Consignes de sécurité importantes

1) Lisez ces instructions.

2) Conservez ces instructions.

3) Respectez tous les avertissements.

4) Respectez toutes les instructions.

5) N’utilisez pas cet appareil à proximité de l’eau.

6) Nettoyez-le uniquement avec un chiffon sec.

7) N’obstruez pas les orifices de ventilation. Installez l’appareil

conformément aux instructions du fabricant.

8) N’installez pas l’appareil à proximité des sources de chaleur telles que

les radiateurs, les registres de chaleur, les poêles ou autres appareils (y

compris les amplificateurs) produisant de la chaleur.

9) N’altérez pas le dispositif de sécurité de la fiche polarisée ou mise à la

terre. Une fiche polarisée compte deux lames de largeur différente. Une

fiche de type mise à la terre possède deux lames et une broche de mise

à la terre. La lame la plus large ou la troisième broche assure une

fonction de sécurité. Si la fiche fournie d’origine ne s’adapte pas à votre

prise, faites remplacer la prise obsolète par un électricien.

10) Protégez le cordon d’alimentation des lieux de passage ou des points

de pincement, en particulier au niveau des fiches, des prises de courant

et de sa sortie de l’appareil.

11) Utilisez uniquement des accessoires spécifiés par le fabricant.

12) Utilisez uniquement l’appareil avec le chariot, socle, trépied, support ou

table spécifié par le fabricant ou vendu avec l’appareil. Si vous utilisez

un chariot, soyez prudent lorsque vous le déplacez avec l’appareil afin

d’éviter toute chute susceptible de provoquer des blessures.

13) Débranchez cet appareil en cas d’orage ou d’inutilisation prolongée.

14) Confiez toutes les réparations à du personnel de service qualifié.

L’appareil doit être réparé en cas de dommage quelconque,

notamment lorsque le cordon d’alimentation ou sa fiche est

endommagé, du liquide ou un objet a pénétré à l’intérieur de l’appareil,

l’appareil a été exposé à la pluie ou à l’humidité, l’appareil ne

fonctionne pas normalement ou est tombé.

AVERTISSEMENT

suite

REMARQUE :

Cet appareil a été testé et s’est révélé conforme aux limites des appareils

numériques de Classe B, conformément à l’alinéa 15 de la réglementation

FCC. Ces limites sont conçues pour assurer une protection raisonnable

contre les interférences nuisibles dans une installation résidentielle. Cet

appareil génère, utilise et peut émettre de l’énergie de fréquence radio

qui, en cas d’installation et d’utilisation non conformes aux instructions,

peut engendrer des interférences nuisibles avec les communications radio.

Il n’est toutefois pas garanti qu’aucune interférence ne surviendra dans

une installation particulière. Si cet appareil altère effectivement la

réception radio ou télévisée, ce qui peut être déterminé en l’éteignant et le

rallumant, nous vous encourageons à essayer de remédier à la situation en

prenant une ou plusieurs mesures ci-après :

 Réorientez ou repositionnez l’antenne de réception.

 Augmentez la distance qui sépare l’appareil du récepteur.

 Raccordez l’appareil à la prise d’un circuit différent de celui auquel le

récepteur est raccordé.

 Sollicitez l’aide de votre détaillant ou d’un technicien en radio/télévision

expérimenté.

Pour toute question au sujet de cet appareil, appeler :

Centre d’information à la clientèle Sony 1-800-222-SONY (7669) ou

http://www.sony.com/.

Le numéro ci-dessous concerne seulement les questions relevant de la

Commission fédérale des communications des États-Unis (FCC).

Information réglementaire

ATTENTION

Vous êtes prévenu que toute modification ou tout changement non

expressément approuvé dans ce manuel peut annuler votre autorisation à

utiliser cet appareil.

Cet appareil ne doit pas se trouver à proximité d’un autre émetteur ou

d’une autre antenne, ou encore être utilisé en même temps que ceux-ci.

Pour les clients au Canada

Le présent appareil est conforme aux CNR d’Industrie Canada applicables

aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d’en compromettre le

fonctionnement.

 Windows Media est une marque déposée ou une marque commerciale

de Microsoft Corporation aux États-Unis et/ou dans d’autres pays.

 Ce produit est protégé par des droits de propriété intellectuelle de

Microsoft Corporation. Il est interdit d’utiliser ou de distribuer cette

technologie hors de ce produit sans disposer d’une licence appropriée de

Microsoft ou d’une filiale de Microsoft autorisée.

 Apple, iPhone, iPod, iPod touch, macOS, Mac et OS X sont des marques

commerciales d’Apple Inc., déposées aux États-Unis et dans d’autres

pays.

App Store est une marque de service d’Apple Inc.

 L’utilisation du badge Made for Apple signifie qu’un accessoire a été

conçu pour être raccordé spécifiquement au produit ou aux produits

Apple identifiés dans le badge, et a été certifié par le constructeur pour

satisfaire les normes de performance d’Apple. Apple n’est pas

responsable du fonctionnement de cet appareil ni de sa conformité avec

les consignes et normes de sécurité.

 Technologie de codage audio et brevets MPEG Layer-3 sous licence

Fraunhofer IIS et Thomson.

Déclaration de conformité

Nom commercial : SONY

No de modèle : TA-CA1

Responsable : Sony Electronics Inc.

Adresse : 16535 Via Esprillo, San Diego, CA 92127 É.-U.

No de téléphone : 858-942-2230

Cet appareil est conforme à la Partie 15 de la réglementation de la FCC

des États-Unis. Son utilisation est sujette aux deux conditions

suivantes : (1) Cet appareil ne doit pas générer d’interférences nuisibles

et (2) il doit être en mesure d’accepter toute interférence reçue, y

compris les interférences pouvant générer un fonctionnement

indésirable.

Droits d’auteur

N Mark est une marque commerciale ou une marque déposée de NFC

Forum, Inc. aux États-Unis et dans d’autres pays.

Le terme et les logos BLUETOOTH® sont des marques déposées

appartenant à Bluetooth SIG, Inc. et tout usage de ces marques par Sony

Corporation s’inscrit dans le cadre d’une licence.

LDAC™ et le logo LDAC sont des marques commerciales de Sony

Corporation.

Android et Google Play sont des marques commerciales de Google LLC.

Les autres marques commerciales et noms de marques appartiennent à

leurs propriétaires respectifs.

AVERTISSEMENT .....................................................................2

Droits d’auteur .......................................................................4

Précautions ............................................................................7

Remplacement de la pile de télécommande ........................8

Désactivation de la fonction BLUETOOTH .............................9

Réinitialisation de l’appareil ..................................................9

Dépannage ........................................................................... 10

Caractéristiques techniques ................................................ 13

À propos de la communication BLUETOOTH® .................... 16

Accord de licence de l’utilisateur final ................................ 17

Table des matières

Reportez-vous au « Manuel d’instructions » fourni

pour les instructions de configuration et

d’utilisation.

Page is loading ...

Sony CAS-1 Owner's manual

Brand: Sony

Model: CAS-1

Category: Bluetooth music receivers

Type: Owner's manual

Download PDF

report

in other languages

français: Sony CAS-1 Le manuel du propriétaire

Sony CAS-1 Owner's manual

Sony CAS-1 Owner's manual

in other languages

Related papers

Other documents