FEC AM-1008W User manual

\ Manual

Page 1 of 21

Model Name:

AM-1008W (8”)

Document Version: V1.1

Customer

N/A

Checked &

Approved by

N/A

Date

FEC

Prepared by

FEC

Approved by

Date

_________

\ Manual

Page 2 of 21

Record of Revision:

Date

Specs

Ver.

Description

Note

2016.07.31

V0.1

Initial Draft

Cary

2016.09.30

V0.2

Add Specs

Cary

2016.10.30

V0.3

Add Customer Display

Cary

2017.01.19

V0.4

Add Setup Instructions, Revised NFC &

Customer Display Section

Cary

2017.02.11

V1.0

First Release

Cary

2017.06.20

V1.1

Update Model Name

Update Command List

Cary

\ Manual

Page 3 of 21

Safety and Warranty

1. Read these safety instructions carefully.

2. Keep this user's manual for later reference.

3. Disconnect from power outlet before cleaning, disassembly or transport. Do

not use liquid or spray detergents for cleaning. Use a damp cloth only and

avoid any prolonged contact with moisture.

4. Keep the unit away from humidity.

5. Place the unit on a sturdy surface before servicing or operation to prevent

accidental drops.

6. The openings on the enclosure are for ventilation. Do NOT cover the

openings.

7. Make sure the voltage and load ratings of the power source are correct before

connecting the equipment to the power outlet.

8. Position the power cord to prevent accidental tripping. Do not twist, pinch or

clip the power cord.

9. All cautions and warnings printed on the equipment should be followed.

10. If the equipment is not used for a long time, disconnect it from the power

source.

11. Never pour any liquid into an opening. This could cause fire or electrical

shock.

12. For safety reasons, only qualified service personnel should open and service

the equipment.

13. If any of the following situations arises, get the equipment checked by service

\ Manual

Page 4 of 21

personnel:

 The power cord, plug, or adapter is visibly damaged.

 Liquid has entered into the equipment.

 The equipment has been exposed to moisture.

 The equipment does not work as intended, or you cannot get it to work

according to the user’s manual.

 The equipment has been dropped and damaged.

 The equipment has obvious signs of breakage.

14. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED

ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°

C (-4°F) OR ABOVE 60° C (140° F).

\ Manual

Page 5 of 21

Contents

Chapter 1 – Introduction 6

About AM-1008W 6

Overview 7

I/O Layout 7

Package Contents 7

Chapter 2 – Hardware & Software 9

Standalone Setup 9

Connecting to System 16

Customer Display Option 16

NFC Option 17

Chapter 3 – Specifications 17

Appendix A – Customer Display Command List 18

\ Manual

Page 6 of 21

Chapter 1 – Introduction

About AM-1008W

AM-1008W is a new type of multifunction LCD display. Featuring 8” widescreen LCD

panel with bright LED backlight, slim frame and innovative features.

Main Features:

 All in one compact design with integrated and standalone mounting

options.

 HD LCD panel with high brightness and contrast for optimal viewing.

 Optional 20x2 Customer Display emulation with overlay.

 Optional NFC module featuring read/write functions

\ Manual

Page 7 of 21

Overview

Unit Dimensions

Mounting Options

Standalone Integrated Mount Wallmount

I/O Layout

AM-1008W features an unique all-in-one connection allowing simple setup and cable

management. A custom-designed connector houses both video and power supply.

Depending on the SKU ordered, your cable may look different from the illustrations

below.

Package Contents

(Content may differ depending on configuration and pre-assembly)

211mm

135mm

\ Manual

Page 8 of 21

Standard

Optional Items

1

AM-1008W Main Display Unit

1

AerARM with Bracket

2

Integrated Cable

2

Extension tubes, standalone base

3

Wallmount Kit

4

\ Manual

Page 9 of 21

Chapter 2 – Hardware & Software

Standalone Setup

1. Unpack the contents

2. Take the two extension tubing and assemble them by pressing the two

nipples inward and slide them into the cavity as shown. The nipple will click

into the opening and lock.

Do not perform any service or upgrade without shutting down the

terminal first. Power must be switched off and power cord must be

unplugged. Failure to do so may result in system damage which is not

covered by FEC warranty.

\ Manual

Page 10 of 21

3. Unwrap the cable from its protective bag and untie the cable tie to loosen the

cables.

CLICK!

\ Manual

Page 11 of 21

4. Starting with the thinnest cable (USB or RS232, thread it through the base

opening as shown.

5. Keeping the threaded cable to the left side, thread the video signal cable

(HDMI or VGA) through as shown.

\ Manual

Page 12 of 21

6. Align the extension tubes with docking socket facing the narrow side of the

base, pull the cables through and assemble the extension tubing to the base

using the method outlined in Step 2.

\ Manual

Page 13 of 21

7. Tilt the stand over and thread the cables as shown (thinnest cable always

first)

CLICK!

\ Manual

Page 14 of 21

8. Dock the screen as shown by aligning the points circled and push the screen

downward to dock with the stand.

9. Lay the unit face down and attach the two screws as shown.

\ Manual

Page 15 of 21

10. Assembly is now complete.

\ Manual

Page 16 of 21

Connecting to System

Please follow these steps to ensure proper function and display resolution.

1. Plug in either the USB or RS232 cable to your system first. If unit is

equipped with NFC module, you will hear a soft beep.

2. Attach the signal cable (HDMI or VGA) to the system. The display

should be functional momentarily.

3. If nothing is displayed, first check your system is configured properly,

then disconnect the cabled and repeat Step 1 & 2 again.

Customer Display Option

AM-1008W can emulate 20x2 VFD compatible with EPSON commands. The

output is displayed using overlay technology.

COM Port Settings

Baud rate: 9600

Data Bit: 8

Parity: None

Stop Bit: 1

Supported Commands

\ Manual

Page 17 of 21

Please refer to command chart at the end of the manual.

NFC Option

1. The NFC module is configured to be HID USB read only by default. To

enable Virtual COM read/write mode, please install the Virtual COM

driver provided by FEC.

2. If the driver is not included, please contact your FEC representative.

Chapter 3 – Specifications

\ Manual

Page 18 of 21

*specifications are subject to change without notice. Contact your nearest FEC

representative for latest information.

Appendix A – Customer Display

Command List

Command

Function Description

09

Move cursor right

08

Move cursor left

1F 0A

Move cursor up

0A

Move cursor down

1F 0D

Move cursor to right-most position

0D

Move cursor to left-most position

0B

Move cursor to home position

1F 42

Move cursor to bottom position

1F 24 x y

Move cursor to specified position

1≦x(column)≦20 ; 1≦y(row)≦2

\ Manual

Page 19 of 21

1F 43 n

Select/cancel cursor display

n=0, canceled ; n=1, selected

0C

Clear display screen

18

Clear cursor line

1F 58 n

Brightness adjustment

1≦n≦4

1F 45 n

Blink display screen

0≦n≦255 (n*50msec) ON / (n*50msec) OFF

n= 0, blinking is canceled

n=255, display is turned off

1B 40

Initialize display

1B 74 n

Select character code table

0≦n≦5 ( Please refer “Chapter 5” )

1B 52 n

Select international character set

( Please refer International Font Set Table )

1F 72 n

Select/cancel reverse character

n=0, canceled ; n=1, selected

Command

Function Description

1F 01

Specify overwrite mode

1F 02

Specify vertical scroll mode

1F 03

Specify horizontal scroll mode

1B 57 n s (x1 y1 x2 y2)

Specify/cancel the window range

n=1,2,3,4 (four windows) ; s=0,1 (disable, enable)

1≦x1≦x2≦20 (column) ; 1≦y1≦y2≦2 (row)

1F 3A

Set starting/ending position of macro definition

1F 5E n m

Execute and quit macro

0≦(n,m)≦255

n: specifies the time interval for display of

characters in units of [n* 50msec]

m: specifies the interval of macro execution every

[m*50msec]

1F 40

Execute self-test

1F 54 h m

Display time :0≦h≦23 ; 0≦m≦59

1F 55

Display of time counter

\ Manual

Page 20 of 21

1A 1B

Enter Burn In Test Mode

1A 1C

Break Burn In test mode

1A 1E

Exit Burn In test mode

1A 01

Display Monitor Model

1A 02 0D

Edit Monitor model name

n = 1 ~ 16 bytes

1A 03 n 0D

Power Saving mode

n = 0, power saving mode off;

n = 1, power saving mode on; (Default)

1E 03

Display A/D board model and firmware version and

production date

1E 06 n 0D

Edit A/D board serial number

n = 1 ~ 32bytes

1E 05

Read A/D board serial number

1E 08 n 0D

Edit Monitor serial number

n = 1 ~ 32bytes

1E 07

Read Monitor serial number

1E 10

Read international character set

1E 11 n

Select international character set (20-7F)

n= 0 ~ B

1E 0C

Read character code table

1E 0B n

Select character code table (80-FF)

n= 0 ~ B

1E 12

Read Baud rate setting

1E 13 E6 DF FF EC 96 00

Write Baud rate setting : 9600

1E 13 69 FF FE C1 92 00

Write Baud rate setting : 19200

1E 13 69 FF FE C3 84 00

Write Baud rate setting : 38400

1E 14

Read Display turn on time

1E 16

Read total transmitted data quantity

1E 20

RESET Customer Display

Page is loading ...

FEC AM-1008W User manual

FEC AM-1008W User manual

Other documents