FEC AM-1008W User manual

  • Hello! I am an AI chatbot trained to assist you with the FEC AM-1008W User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
\ Manual
Page 1 of 21
Model Name:
AM-1008W (8)
Document Version: V1.1
Customer
N/A
Checked &
Approved by
N/A
Date
FEC
Prepared by
FEC
Approved by
Date
_________
\ Manual
Page 2 of 21
Record of Revision:
Date
Specs
Ver.
Description
2016.07.31
V0.1
Initial Draft
2016.09.30
V0.2
Add Specs
2016.10.30
V0.3
Add Customer Display
2017.01.19
V0.4
Add Setup Instructions, Revised NFC &
Customer Display Section
2017.02.11
V1.0
First Release
2017.06.20
V1.1
Update Model Name
Update Command List
\ Manual
Page 3 of 21
Safety and Warranty
1. Read these safety instructions carefully.
2. Keep this user's manual for later reference.
3. Disconnect from power outlet before cleaning, disassembly or transport. Do
not use liquid or spray detergents for cleaning. Use a damp cloth only and
avoid any prolonged contact with moisture.
4. Keep the unit away from humidity.
5. Place the unit on a sturdy surface before servicing or operation to prevent
accidental drops.
6. The openings on the enclosure are for ventilation. Do NOT cover the
openings.
7. Make sure the voltage and load ratings of the power source are correct before
connecting the equipment to the power outlet.
8. Position the power cord to prevent accidental tripping. Do not twist, pinch or
clip the power cord.
9. All cautions and warnings printed on the equipment should be followed.
10. If the equipment is not used for a long time, disconnect it from the power
source.
11. Never pour any liquid into an opening. This could cause fire or electrical
shock.
12. For safety reasons, only qualified service personnel should open and service
the equipment.
13. If any of the following situations arises, get the equipment checked by service
\ Manual
Page 4 of 21
personnel:
The power cord, plug, or adapter is visibly damaged.
Liquid has entered into the equipment.
The equipment has been exposed to moisture.
The equipment does not work as intended, or you cannot get it to work
according to the users manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
14. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -2
C (-4°F) OR ABOVE 60° C (14 F).
\ Manual
Page 5 of 21
Contents
Chapter 1 Introduction 6
About AM-1008W 6
Overview 7
I/O Layout 7
Package Contents 7
Chapter 2 Hardware & Software 9
Standalone Setup 9
Connecting to System 16
Customer Display Option 16
NFC Option 17
Chapter 3 Specifications 17
Appendix A Customer Display Command List 18
\ Manual
Page 6 of 21
Chapter 1 Introduction
About AM-1008W
AM-1008W is a new type of multifunction LCD display. Featuring 8” widescreen LCD
panel with bright LED backlight, slim frame and innovative features.
Main Features:
All in one compact design with integrated and standalone mounting
options.
HD LCD panel with high brightness and contrast for optimal viewing.
Optional 20x2 Customer Display emulation with overlay.
Optional NFC module featuring read/write functions
\ Manual
Page 7 of 21
Overview
Unit Dimensions
Mounting Options
Standalone Integrated Mount Wallmount
I/O Layout
AM-1008W features an unique all-in-one connection allowing simple setup and cable
management. A custom-designed connector houses both video and power supply.
Depending on the SKU ordered, your cable may look different from the illustrations
below.
Package Contents
(Content may differ depending on configuration and pre-assembly)
211mm
135mm
\ Manual
Page 8 of 21
Standard
Optional Items
1
AM-1008W Main Display Unit
1
AerARM with Bracket
2
Integrated Cable
2
Extension tubes, standalone base
3
3
Wallmount Kit
4
4
\ Manual
Page 9 of 21
Chapter 2 Hardware & Software
Standalone Setup
1. Unpack the contents
2. Take the two extension tubing and assemble them by pressing the two
nipples inward and slide them into the cavity as shown. The nipple will click
into the opening and lock.
Do not perform any service or upgrade without shutting down the
terminal first. Power must be switched off and power cord must be
unplugged. Failure to do so may result in system damage which is not
covered by FEC warranty.
\ Manual
Page 10 of 21
3. Unwrap the cable from its protective bag and untie the cable tie to loosen the
cables.
CLICK!
\ Manual
Page 11 of 21
4. Starting with the thinnest cable (USB or RS232, thread it through the base
opening as shown.
5. Keeping the threaded cable to the left side, thread the video signal cable
(HDMI or VGA) through as shown.
\ Manual
Page 12 of 21
6. Align the extension tubes with docking socket facing the narrow side of the
base, pull the cables through and assemble the extension tubing to the base
using the method outlined in Step 2.
\ Manual
Page 13 of 21
7. Tilt the stand over and thread the cables as shown (thinnest cable always
first)
CLICK!
\ Manual
Page 14 of 21
8. Dock the screen as shown by aligning the points circled and push the screen
downward to dock with the stand.
9. Lay the unit face down and attach the two screws as shown.
\ Manual
Page 15 of 21
10. Assembly is now complete.
\ Manual
Page 16 of 21
Connecting to System
Please follow these steps to ensure proper function and display resolution.
1. Plug in either the USB or RS232 cable to your system first. If unit is
equipped with NFC module, you will hear a soft beep.
2. Attach the signal cable (HDMI or VGA) to the system. The display
should be functional momentarily.
3. If nothing is displayed, first check your system is configured properly,
then disconnect the cabled and repeat Step 1 & 2 again.
Customer Display Option
AM-1008W can emulate 20x2 VFD compatible with EPSON commands. The
output is displayed using overlay technology.
COM Port Settings
Baud rate: 9600
Data Bit: 8
Parity: None
Stop Bit: 1
Supported Commands
\ Manual
Page 17 of 21
Please refer to command chart at the end of the manual.
NFC Option
1. The NFC module is configured to be HID USB read only by default. To
enable Virtual COM read/write mode, please install the Virtual COM
driver provided by FEC.
2. If the driver is not included, please contact your FEC representative.
Chapter 3 Specifications
\ Manual
Page 18 of 21
*specifications are subject to change without notice. Contact your nearest FEC
representative for latest information.
Appendix A Customer Display
Command List
Command
Function Description
09
Move cursor right
08
Move cursor left
1F 0A
Move cursor up
0A
Move cursor down
1F 0D
Move cursor to right-most position
0D
Move cursor to left-most position
0B
Move cursor to home position
1F 42
Move cursor to bottom position
1F 24 x y
Move cursor to specified position
1x(column)20 ; 1y(row)2
\ Manual
Page 19 of 21
1F 43 n
Select/cancel cursor display
n=0, canceled ; n=1, selected
0C
Clear display screen
18
Clear cursor line
1F 58 n
Brightness adjustment
1n4
1F 45 n
Blink display screen
0n255 (n*50msec) ON / (n*50msec) OFF
n= 0, blinking is canceled
n=255, display is turned off
1B 40
Initialize display
1B 74 n
Select character code table
0n5 ( Please refer “Chapter 5” )
1B 52 n
Select international character set
( Please refer International Font Set Table )
1F 72 n
Select/cancel reverse character
n=0, canceled ; n=1, selected
Command
Function Description
1F 01
Specify overwrite mode
1F 02
Specify vertical scroll mode
1F 03
Specify horizontal scroll mode
1B 57 n s (x1 y1 x2 y2)
Specify/cancel the window range
n=1,2,3,4 (four windows) ; s=0,1 (disable, enable)
1x1x220 (column) ; 1y1y22 (row)
1F 3A
Set starting/ending position of macro definition
1F 5E n m
Execute and quit macro
0(n,m)255
n: specifies the time interval for display of
characters in units of [n* 50msec]
m: specifies the interval of macro execution every
[m*50msec]
1F 40
Execute self-test
1F 54 h m
Display time :0h23 ; 0m59
1F 55
Display of time counter
\ Manual
Page 20 of 21
1A 1B
Enter Burn In Test Mode
1A 1C
Break Burn In test mode
1A 1E
Exit Burn In test mode
1A 01
Display Monitor Model
1A 02 0D
Edit Monitor model name
n = 1 ~ 16 bytes
1A 03 n 0D
Power Saving mode
n = 0, power saving mode off;
n = 1, power saving mode on; (Default)
1E 03
Display A/D board model and firmware version and
production date
1E 06 n 0D
Edit A/D board serial number
n = 1 ~ 32bytes
1E 05
Read A/D board serial number
1E 08 n 0D
Edit Monitor serial number
n = 1 ~ 32bytes
1E 07
Read Monitor serial number
1E 10
Read international character set
1E 11 n
Select international character set (20-7F)
n= 0 ~ B
1E 0C
Read character code table
1E 0B n
Select character code table (80-FF)
n= 0 ~ B
1E 12
Read Baud rate setting
1E 13 E6 DF FF EC 96 00
Write Baud rate setting : 9600
1E 13 69 FF FE C1 92 00
Write Baud rate setting : 19200
1E 13 69 FF FE C3 84 00
Write Baud rate setting : 38400
1E 14
Read Display turn on time
1E 16
Read total transmitted data quantity
1E 20
RESET Customer Display
/