Broan ILB11 Installation guide

Brand: Broan

Model: ILB11

Type: Installation guide

This manual is also suitable for

Page 1

MODELS ILB9 !!

! ILB11

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer at the address

or telephone number listed in the warranty.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent power

from being switched on accidentally. When the service discon-

necting means cannot be locked, securely fasten a prominent

warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a quali-

fied person(s) in accordance with all applicable codes and stan-

dards, including fire-rated construction codes and standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equipment

to prevent backdrafting. Follow the heating equipment

manufacturer’s guideline and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air Con-

ditioning Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage elec-

trical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce the risk of fire, use only metal ductwork.

8. If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to

a GFCI (Ground Fault Interrupter) - protected branch circuit.

9. Never place a switch where it can be reached from a tub or

shower.

10. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Pepper-

corn Beef Flambe’).

3. Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the

size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT

OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOW-

ING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal

tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. If the flames do not go out immediately, EVACUATE

AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels - vio-

lent steam explosion will result.

IN-LINE BLOWERS

READ AND SAVE THESE INSTRUCTIONS

Installer: Leave this manual with

the homeowner.

Homeowner: Use and Care

information on page 4.

FOR DOMESTIC COOKING ONLY

WARNING

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you already

know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power

unit.

3. If ventilator is installed in an unconditioned space (such as

an attic): Surround the ventilator with thermal insulation - to

minimize possible condensation.

4. Please read specification label on product for further informa-

tion and requirements.

TABLE OF CONTENTS

This manual is divided into sections as follows:

!“TYPICAL INSTALLATION”

This section shows a common installation.

- Mounting (New Frame Construction)

- Mounting (Existing Frame Construction)

- Mounting Using Hanger Kit (included)

- Ducting (Horizontal blower discharge)

- Wiring

!“MOUNTING OPTIONS”

!“WIRING PLATE POSITION”

!“DUCTING OPTIONS”

- Blower Discharge Positions

- Ducting (Vertical blower discharge)

!“USE AND CARE”

!“SERVICE PARTS”

!“WARRANTY”

Page 2

MODELS ILB9 !!

! ILB11

MOUNTING USING HANGER KIT (included)

Blower factory-shipped in straight-through

discharge position.

TYPICAL INSTALLATION

DUCTING (Horizontal blower discharge)

Two ways to connect ductwork to a factory-shipped unit.

ROOF CAP

10” ROUND

ELBOW

10”

ROUND

DUCT

WALL

CAP

8” X 12”

10” ROUND

TRANSITIONS

10”

ROUND

DUCT

ACCESS

PANEL ACCESS

PANEL SCREW

GRILLE NUT

(Install into

square holes in

housing)

MOUNTING

BRACKET

10” ROUND

DUCT

(OUTLET)

8” X 12” TO

10” ROUND

TRANSITIONS

10” ROUND

DUCT (INTAKE)

HANGER

KIT NUT &

WASHER

HANGER

KIT BOLT

& WASHER

HANGER

KIT CHAIN

HANGER KIT

EYE-BOLT

TYPICAL INSTALLATION

MOUNTING (New Frame Construction)

CEILING

JOIST

(24”

centers

shown)

10” ROUND

DUCT

(OUTLET)

ACCESS

PANEL

Factory-shipped unit installed in new construction.

MOUNTING

SCREWS

ACCESS

PANEL SCREW

Ventilator factory-shipped

in straight-through

discharge position.

MOUNTING

BRACKETS

MOUNTING (Existing Frame Construction)

Factory-shipped unit installed in existing construction.

ACCESS

PANEL

SCREW

8” X 12” TO 10” ROUND

TRANSITIONS

10” ROUND DUCT

(OUTLET)

Ventilator

factory-shipped

in straight-through

discharge position.

MOUNTING

BRACKETS

8” X 12” TO

10” ROUND

TRANSITIONS

CEILING

JOIST

(24” centers

shown)

ACCESS PANEL

10” ROUND

DUCT

(INTAKE)

10” ROUND

DUCT (INTAKE)

GRILLE NUT

(Install into square

holes in housing)

GRILLE NUT

(Install into

square

holes in

housing)

IMPORTANT: Remove shipping tape from damper

Remove the shipping tape from the damper flap and make sure

that damper flap opens and closes freely inside the ductwork. Use

duct tape to make ductwork connections secure and air-tight.

EXTENSION

SPRING

Page 3

MODELS ILB9 !!

! ILB11

WIRING PLATE POSITION

DUCTING OPTIONS

BLOWER DISCHARGE POSITIONS

Wiring plate mounts to side or top of housing.

HORIZONTAL POWER

CABLE CONNECTION

VERTICAL

POWER

CABLE

CONNECTION

Ventilator shown in

straight-through discharge

position. (Factory shipped)

DUCT

CONNECTOR

(intake)

Ventilator shown in right-

angle discharge position.

(Change movable panel to

new location as shown.)

MOVABLE

PANEL

DUCTING (Vertical blower discharge)

Typical ductwork connection to a ventilator converted to

right-angle discharge.

ROOF CAP

10” ROUND

DUCT

MOVABLE

PANEL

(Change to this

location)

8” X 12” TO

10” ROUND TRANSITIONS

DUCT

CONNECTOR

(outlet)

DUCT

CONNECTOR

(intake)

DUCT

CONNECTOR

(outlet)

Housing

rotated &

movable panel

covers previous

open side.

10” ROUND

DUCT

WIRING

PLATE

WHITE

BLACK

BLACK EDGE

OF HOUSING

120 VAC LINE IN

(from range hood)

GROUND TO

WIRING PLATE

Ventilator can be wired from outside of housing.

Use UL approved connectors to wire per local codes.

18"

1½"

2½"

18"

1½"

2½"

22"

MAX.

MOUNTING OPTIONS

Mounting brackets in

factory-shipped position -

mounted directly to joists.

(Outlet parallel to joists.)

(New construction)

¼-20 hex nuts secure mounting brackets to housing. Loosen and

re-tighten or remove and replace nuts as necessary for desired

mounting bracket position.

Mounting brackets flipped

over and mounted to

additional framing.

(Outlet perpendicular to joists.)

(New or Existing construction)

Factory-Shipped

Straight-Through

Discharge

Factory-Shipped

Straight-Through

Discharge

Housing

Converted to

Right-Angle

Discharge

Mounting brackets flipped

over and mounted to

additional framing.

(Outlet vertical.)

(New or Existing construction)

Mounting brackets flipped

over and mounted to top of

housing. Housing secured

with cables.

(Outlet parallel to joists.)

(New or Existing construction)

Factory-Shipped

Straight-Through

Discharge

WIRING

Page 4

MODELS ILB9 !!

! ILB11

SERVICE PARTS

KEY NO. PART NO. DESCRIPTION

1 97014853 Damper Flap

2 99150415 Screw, #8B x ¼* (16 req.)

3 98009520 Duct Connector (2 req.)

4 97014784 Housing Assembly

5 97014728 Mounting Bracket (2 req.)

6 99150591 Mounting Screw (4 req.)

7 97006142 Wiring Harness

8 99150471 Ground Screw, #10-32 x ½* (2 req.)

9 98005512 Wiring Adapter Plate

10 99420470 Access Panel Nut (4 req.)

11 98009531 Movable Housing Panel

12 93150487 Screw, #10-24 x .375* (8 req.)

13 98005513 Outlet Box Cover

14 99400035 Strain Relief Bushing

15 97014788 Motor Bracket

16 99260477 Whiz Nut, ¼-20* (11 req.)

17 99200202 Screw, ¼-20 x ½* (5 req.)

18 97014785 Blower Scroll

19 99080490 Motor (ILB9)

99080491 Motor (ILB11)

20 93260447 Nut, Hex Flange 5/16-18* (5 req.)

21 98009516 Support Bracket

22 99020286 Blower Wheel

23 98009514 Inlet Ring

24 99150417 Screw, #8-18 x ¼* (5 req.)

25 98009513 Scroll Support Channel

+ 97016796 Blower Assembly Complete (ILB9)

(Includes Key Nos. 15 thru 25)

+ 97016797 Blower Assembly Complete (ILB11)

(Includes Key Nos. 15 thru 25)

26 98009532 Access Cover

27 99150472 Access Cover Screw (4 req.)

28 97016791 Hanger Kit

29 99610015 Transition 8” x 12” to 10” Round (2 req.)

30 97014597 Rough-In Kit

Order replacement parts by PART NO. - not by KEY NO.

* Standard hardware - may be purchased locally.

+ Not shown assembled.

15 16

BLOWER

ASSEMBLY

99043703C

WARRANTY

WARNING: To reduce the risk of electric shock,

disconnect from power supply before servicing.

To clean blower assembly: Remove access panel, unplug blower

from housing, remove blower mounting nuts, and carefully remove

blower from housing. Use appropriate vacuum attachment or a

soft cloth and mild soap or detergent to clean blower discharge

area and wheel. DO NOT ALLOW WATER TO ENTER MOTOR.

Make sure blower assembly is completely dry before reinstalling.

Motor is permanently lubricated. Do not oil or disassemble motor.

USE AND CARE

Follow wiring instructions packed with range hood, and adhere to

all local and state codes, and the National Electrical Code.

BROAN ONE YEAR LIMITED WARRANTY

Broan warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

During this one-year period, Broan will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service.

THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS AND TUBES. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject

to misuse, negligence, accident, improper maintenance or repair (other than by Broan), faulty installation or installation contrary to recommended installation instructions.

The duration of an implied warranty is limited to the one-year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply

to you.

BROAN’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN SHALL NOT BE LIABLE FOR

INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.

To qualify for warranty service, you must (a) notify Broan at the address or phone number stated below (b) give the model number and part identification and (c) describe the nature of any defect in the product or part.

At the time of requesting warranty service, you must present evidence of the original purchase date.

Best by Broan, P.O. Box 140, Hartford, WI 53027 (1-800-637-1453)

1 / 1