Legrand On-Q Module to GreyFox Mounting Plate - F9002 Installation guide

Type
Installation guide

Legrand On-Q Module to GreyFox Mounting Plate - F9002

The Legrand On-Q Module to GreyFox Mounting Plate - F9002 is a mounting solution that allows for the easy installation of multiple On-Q modules in a Foxbox or Titan enclosure. The plate features multiple push-pins for secure mounting, and it can accommodate both half-width and full-width On-Q modules.

Capabilities:

  • Mounts On-Q modules in a vertical orientation
  • Supports half-width and full-width On-Q modules
  • Can be mounted directly above or below another plate for additional support
  • Includes four inner holes for mounting an F7520 module mounting bracket

Legrand On-Q Module to GreyFox Mounting Plate - F9002

The Legrand On-Q Module to GreyFox Mounting Plate - F9002 is a mounting solution that allows for the easy installation of multiple On-Q modules in a Foxbox or Titan enclosure. The plate features multiple push-pins for secure mounting, and it can accommodate both half-width and full-width On-Q modules.

Capabilities:

  • Mounts On-Q modules in a vertical orientation
  • Supports half-width and full-width On-Q modules
  • Can be mounted directly above or below another plate for additional support
  • Includes four inner holes for mounting an F7520 module mounting bracket
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
Page 1 of 2
©Copyright 2005 by On-Q/Legrand All Rights Reserved.
INSTRUCTION/INSTALLATION SHEET
On-Q Module to GF Mounting Plate
IS-0323 REV. C
1. Introduction
The On-Q Module to GF Mounting Plate (P/N F9002 as shown below) is designed to easily mount multiple
On-Q modules in a Foxbox or Titan enclosure.
2. Description
The On-Q Module to GF Mounting Plate, (see Figure 1) is designed to be mounted in a Foxbox or Titan
enclosure with multiple push-pins (typically at each corner). On-Q half-width modules can then be mounted in
a vertical orientation (90°counter-clockwise rotation), inserting the tabs into the square holes along the bottom
edge of the plate and using the locking tab/s (push-pin/s) at the other end of the module in the round holes
along the top edge of the plate. If full width On-Q modules need to be supported, an additional plate may be
mounted directly above or below the first plate (see Figure 2).
NOTE: The four inner holes on each side of the plate can be used to mount an F7520 module
mounting bracket which holds 2 single bay or I double bay module.
3. Installation
The On-Q Module to GF Mounting Plate is typically installed during “trim-out” or as an upgrade for an
existing installation.
a. Align the holes on the outer flanges of the plate with those in the enclosure and use push-pins to secure
the plate to the enclosure (see Figure 1).
b. To attach On-Q modules, align the two stationary tabs on the module with the square slots on the
mounting plate (see Figure 2).
c. Insert tabs by angling module away from the plate and sliding forward.
Figure 1
Secure plate here
with push-pins
Secure plate here
with push-pins
P/N F9002
Mount F7520 here
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
Page 2 of 2
©Copyright 2005 by On-Q/Legrand All Rights Reserved.
INSTRUCTION/INSTALLATION SHEET
On-Q Module to GF Mounting Plate
IS-0323 REV. C
d. Rotate the module and insert the built in locking tab (push-pin) on the module into the corresponding hole
on the top edge of the mounting plate, pushing in until it snaps into place (see Figure 2).
e. Pull lightly on the module to assure it is properly locked in place.
Figure 2
Half-width
On-Q Modules
Full-width
On-Q Module
On-Q Module
push-pin
On-Q Module tabs
  • Page 1 1
  • Page 2 2

Legrand On-Q Module to GreyFox Mounting Plate - F9002 Installation guide

Type
Installation guide

Legrand On-Q Module to GreyFox Mounting Plate - F9002

The Legrand On-Q Module to GreyFox Mounting Plate - F9002 is a mounting solution that allows for the easy installation of multiple On-Q modules in a Foxbox or Titan enclosure. The plate features multiple push-pins for secure mounting, and it can accommodate both half-width and full-width On-Q modules.

Capabilities:

  • Mounts On-Q modules in a vertical orientation
  • Supports half-width and full-width On-Q modules
  • Can be mounted directly above or below another plate for additional support
  • Includes four inner holes for mounting an F7520 module mounting bracket

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI