Noble House 42840 Operating instructions

Type
Operating instructions

This manual is also suitable for

Page1 of 6
Caution : You must read this before you proceed
TABLE
CAUTION : This Table is NOT a TOY.
Keep your child / children at bay in the process of
assembly.
For turning the Table and to prevent damage to the Table,
02 persons may be needed to execute this action.
Noble House Home Furnishings LLC
Page2 of 6
Label Picture Description QTY
A Table Top 1
B Leg 4
Label Picture Description QTY
Bolt
(M8x55mm)
9
Spring Washer
(M8.5/10.5x2mm)
9
Flat Washer
(M8.5/16x2mm)
9
Allen Key 1
Noble House Home Furnishings LLC
Page3 of 6
Overview
Before Beginning Assembly:
Overview
This Table has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Table parts, the above picture is to help you put the various parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps before
assembly.
FRONT FACING
Table top (A)
Leg (B)
Noble House Home Furnishings LLC
Page4 of 6
Step 1
Step 2
Unpack and place all parts on a clean, non-marring surface.
Step 2.1
A
4
2
2.1) With assistance from your adult partners, turn the Table Top (A) up
side down as picture shown
2.2) Attach Leg (B) to Table Top (A) by using Bolt (), Spring Washer
(), Flat Washer () and Allen Key ()
Repeat the same process with the other 3 Legs (B)
Do not fully tighten the Bolts.
Step 2.2
A
A
B
1
3
2
Noble House Home Furnishings LLC
Page5 of 6
Step 3
With assistance from your adult partners, turn the Table back to
normal flat ground
EXERT pressure, floorwards, onto the Table.
This pressure will help the Legs and Table Top reach alignment at
all joints.
Check for wobbles.
In a sequential manner, gradually tighten all Bolts until evenly
secured.
Inspect the Table and make sure all parts are adequately
connected.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Noble House Home Furnishings LLC
Page6 of 6
OUTDOOR
Noble House Home Furnishings LLC
Label Picture Description QTY
A Left Armrest / Leg 1
B Right Armrest / Leg 1
C Seat 1
D Seat Back 1
Caution: You must read this before you proceed
Single Chair
Label Picture Description QTY
E Allen Key 1
F
Bolt
(
M6*30mm
)
5
G
Bolt
(M6*40mm)
3
H
Bolt
(M6*60mm)
3
I Washer 13
J Seat Cushion 1
K
Bolt
(
M6*20mm
)
2
L Connection 1
M Connection 1
Before Beginning Assembly:
Step 1
Step 2
Open the carton and place all the parts on a clean, non-marring surface.
ATTENTION: Occasionally some of the PE Wicker shifts and covers the mounting
positions preventing easy assembly.
The PE wicker should never be cut, but moved away from the mounting positions.
Attach Left Armrest / Leg(A) to the Seat(C) using Bolt(F) and Washer(I) with Allen Key(E)
as shown in the picture above.
Loosely tighten the Bolts.
Attach Seat Back(D) to Seat(C) using Washer(I) , Bolt(G&K) &Connection(L&M) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 4
Connect the Chair Legs(A&B) with the Seat Back(D) using Washer(I) and Bolt(H) with
Allen Key(E) as pictured above.
Loosely tighten the Bolts.
Step 3
Attach Right Armrest / Leg(B) to Seat(C) using Bolt(F) and Washer(I) with Allen Key(E ) as
shown in the picture above.
Loosely tighten the Bolts.
Place the Seat Cushion(J) on the Chair.
Your Chair is ready for use.
Step 5
Check for stability and then tighten all Bolts at all joints.
Note: DO NOT fully tighten a Bolt in one go and then move on to the next.
Rather; in a sequential manner, gradually tighten each Bolt until all Bolts are evenly
secured.
This methodology will ensure maximum evenness once all Bolts are fully tightened.
Step 6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Noble House 42840 Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI