iSYFIX Black Vinyl Numbers Stickers - 4 Inch Self Adhesive - 2 Sets - Premium Decal Die Cut and Pre-Spaced for Mailbox, Signs, Window, Door, Cars, Trucks, Home, Business, Address Number, Indoor or Outdoor User guide

Type
User guide
®
Smart signs
Install Guide For Pre-Spaced Number Decals
Attention, Please Read This FIRST Before Apply
The Stickers will adhere better on smooth flat surfaces like glass, painted metal, wood with
lacquer etc.
Do not apply in cold weather (under 50 degrees) - adhesive may stick but will lift easily.
Do not apply in extreme heat (over 90 degrees) - apply in the shade - Hot vinyl will get very soft
and stretch making it difficult to adhere.
Do not use alcohol to apply - it will destroy the adhesive. Just use it to clean your surface well,
let it dry before trying to apply.
Do not use ice scraper or putty knife on the sticker/decal – sharp edges may cause it to lift or
chip pieces off.
Do not touch the adhesive backing of the decal - oils from your skin will prevent it from stic-
king.
Before application make sure there is no wax or cleaning products on the surface - adhesive
may stick but will lift easily.
Don't apply wax over graphics, especially if the wax contains any petroleum distillates.
STEP 1:
CLEAN CLEAN CLEAN the surface you want to use,
Vinyl graphics stick best to smooth clean surfaces. To
ensure good adhesion to any painted surface, it is critical
that you follow these recommended procedures in
decontaminating and preparing the surface prior to any
vinyl product installation.
1. Wash and rinse the area with liquid dish detergent and
warm water – really scrub it down. Then dry the surface
with a clean, lint-free towel or cloth.
2. Finish up the cleaning process by wiping down the
entire area with Isopropyl (rubbing) Alcohol. To avoid
recontamination during the final cleaning step, wipe the
surface in just one direction, using a clean, lint-free towel
or cloth. Let the alcohol evaporate completely. You are
now ready to apply the vinyl.
www.isyfix.com
iSYFIX® is a registered brand of
DNA Gadgets LLC, Las Vegas, NV.
®
Smart signs
Install Guide For Adhesive Stickers
STEP 2:
Your numbers will arrive with three layers:
a) The top layer is a transparent transfer tape,
which holds the numbers in place for easy
installation.
b)The middle layer is the Vinyl numbers.
c)The bottom layer is the white wax paper bac-
king, which protects the Vinyl numbers and the
adhesive.
d) The numbers are precut and pre-spaced for a
seamless application.
www.isyfix.com
iSYFIX® is a registered brand of
DNA Gadgets LLC, Las Vegas, NV.
STEP 5:
Align the sticker in
the desired position
and firmly apply pres-
sure with your hand
to fix the sticker with
the exposed adhesi-
ve.
STEP 6:
With the left hand
start to gently pull the
release paper liner
below the sticker
while you continue to
applying pressure up
and down with your
hand or a plastic card
to adhere the rest of
the sticker on the sur-
face.
Finnaly remove gently
the transparent trans-
fer tape.
STEP 3:
Select the numbers you
want to use and align it
(see the picture), apply
masking tape between
each one to fix the posi-
tion.
Now apply masking tape
to the backing side
between each number.
STEP 4:
Peel a small strip of the
Sticker to expose the
adhesive and bend the
paper liner like is shown
in the image.
NOTE:
If after the instalation are remaining bubbles below
the numbers use a needle to punch it and release
the trapped air.
  • Page 1 1
  • Page 2 2

iSYFIX Black Vinyl Numbers Stickers - 4 Inch Self Adhesive - 2 Sets - Premium Decal Die Cut and Pre-Spaced for Mailbox, Signs, Window, Door, Cars, Trucks, Home, Business, Address Number, Indoor or Outdoor User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI