Eneo HDC-2180Z03 D Quick Installation Manual

Brand: Eneo

Model: HDC-2180Z03 D

Category: Security cameras

Type: Quick Installation Manual

This manual is also suitable for

HDC-2080Z03

The Eneo HDC-2180Z03 D is a high-definition surveillance camera with a powerful 3x optical zoom lens and 1920x1080 resolution, providing clear and detailed images. It features wide dynamic range (WDR) technology to ensure excellent image quality in challenging lighting conditions, and day/night functionality with an IR cut filter for clear night vision. Additionally, the camera offers 3D noise reduction to reduce image noise and improve image quality, especially in low-light conditions.

Quick Installation Guide

1/3” HDcctv Camera, WDR,

Day&Night, 1920x1080, 3x

AF Zoom, 12/24V

HDC-2080Z03 D (3-9mm)

HDC-2180Z03 D (9-22mm)

Table of content

Notes on safety .............................................................................................................3

Parts supplied ...............................................................................................................3

Part names .....................................................................................................................4

Installation instructions ...............................................................................................6

Power supply connections .............................................................................................................................................6

Set the video format according to system, EX-SDI or HD-SDI ........................................................................... 6

Operating instructions .................................................................................................8

Using OSD controller........................................................................................................................................................8

Description of the joystick operation ..........................................................................................................8

Description of the ZOOM&FOCUS adjustment .......................................................................................8

OSD menu startup ............................................................................................................................................................8

Direct control menu .........................................................................................................................................................9

Further information ......................................................................................................9

Parts supplied

• Zoom box camera

• Operating instructions

Notes on safety

Please also pay attention to the enclosed safety instructions, and carefully read through

this instruction guide before initial operation.

Important points of warning are marked with a caution symbol.

Important points of advice are marked with a notice symbol.

Part names

Mount Holes (Top / Bottom)

Rear Case

Front Case

Window

B OSD Control Joy stick

C Power input terminal (AC24V/DC12V or DC12V)

D RS-485 / IR connector

E HD-SDI/EX-SDI output connector

F Power LED

G CVBS output connector

H Video format Switch

Installation instructions

CAUTION: The mounting bracket should be attached to a struc-

tural object, such as concrete, hard wood, wall stud or ceiling

rafter that supports the weight of the camera. If necessary use

appropriate mounting material (e.g. anchors) instead of the

material enclosed with the mounting bracket.

• Make sure the power is removed before the installation.

• Follow the order for applying power.

• First connect the low voltage (DC12V or AC24V), then plug the AC adapter to AC

outlets to avoid an improper reset from power jitter and a damage from the surge

voltage when no load.

• Mount the camera to the wall or ceilling with a corresponding mounting bracket

through the camera mount holes (1/4" thread insert) on its top or bottom.

CAUTION:

Care should be taken the cable is NOT to be damaged, kinked or

exposed in the hazardous area.

Do not expose the camera directly to a strong light source such

as the sun or spot light.

Power supply connections

Make sure the power is removed before the installation. Camera can work with either

24AC or 12VDC, dual voltage power. Primary and secondary grounds are completely

isolated to avoid the possible ground-loop problems.

In case that HD-SDI/EX-SDI Inputs are not supported in monitor, please use HD-SDI/

EX-SDI Converter to connect HD-SDI/EX-SDI cable with monitor. Some computer moni-

tors or TVs may not support 30p/25p. In this case, HD-SDI/EX-SDI DVR which can convert

the frame rate to 60p/50p is highly recommended. Please check specication of monitor

before installation.

Set the video format according to system, EX-SDI or HD-SDI

To select the camera’s output video format (EX-SDI or HD-SDI), use the Video format

Switch on the side of the camera. Only one format can be used at a time (see also “Using

OSD controller”).

Page is loading ...

Operating instructions

Using OSD controller

Setup menu can be accessed and controlled by OSD control joy stick on the side of cam-

era unit. Five commands are available with the joy stick.

Description of the joystick operation

1. SET Key (●) : Access to the menu or enter the setting. To enter the main menu,

press the Set Key down for about 1.5sec

2. UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move the cursor up or

down.

3. LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu. Used to adjust the

desired menu selection and to move the cursor left or right.

4. ‘☟’ denotes the long press down straightly for about 2 seconds

Description of the ZOOM&FOCUS adjustment

Works only when OSD Menu is inactive.

1. ▲ : Zoom In

2. ▼ : Zoom Out

3. ◄ : Focus Near

4. ► : Focus Far

OSD menu startup

Press ‘●’ (OSD menu Joy stick key) down for about 2 seconds to access the setup menu

mode.

Lens Initializing is strongly recommended at the rst stage of setup menu control.

ZOOM/FOCUS > LENS INIT > Press the joystick ‘☟’ straight down for about 2 seconds.

Further information

The manual is available from the eneo web site at www.eneo-security.com or from the CD

supplied with this product.

MENU V5.xx

1. ZOOM/FOCUS

2. EXPOSURE

3. SCENE ENHANCE

4. 3D-NR

5. DAY/NIGHT

6. PICT ADJUST

7. SPECIAL

8. SYSTEM

9. EXIT

↵

NORMAL

MID

EXT

SAVE&EXIT

↵

Direct control menu

MAIN DEFAULT DESCRIPTION

ZOOM/FOCUS - Sets FOCUS and ZOOM relative functions.

EXPOSURE - Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and MOTION DEBLUR.

SCENE ENHANCE NORMAL

SCENE ENHANCE provides the several ways to enhance the video in the various environments with

the settings in NORMAL, WDR, D-WDR, BLC and HLC.

3D-NR MID Sets 3DNR level. LOW, MID, HIGH

DAY/NIGHT EXT or AUTO

Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and COLOR D/N. Setting EXT mode for cameras with

IR-LED, AUTO mode for none IR-LED camera types.

PICT ADJUST Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA

SPECIAL Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET DISPLAY, DEFOG, POINTING ZOOM

SYSTEM Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE an FACTORY DEFAULT

EXIT

SAVE & EXIT – Exits the menu after saving the parameters. EXIT – Exits the menu without saving

the menu.

Page is loading ...

eneo® is a registered trademark of

VIDEOR E. Hartig GmbH

Exclusive distribution through specialised

trade channels only.

VIDEOR E. Hartig GmbH

Carl-Zeiss-Straße 8

63322 Rödermark/Germany

Tel. +49 (0) 6074 / 888-0

Fax +49 (0) 6074 / 888-100

www.videor.com

www.eneo-security.com

Technical changes reserved

Version 05/2015

Eneo HDC-2180Z03 D Quick Installation Manual

Brand: Eneo

Model: HDC-2180Z03 D

Category: Security cameras

Type: Quick Installation Manual

This manual is also suitable for

HDC-2080Z03

Download PDF

report

in other languages

français: Eneo HDC-2180Z03 D
Deutsch: Eneo HDC-2180Z03 D

Eneo HDC-2180Z03 D Quick Installation Manual

This manual is also suitable for

Eneo HDC-2180Z03 D Quick Installation Manual

in other languages

Related papers

Other documents