Eneo HDC-2080Z03 Quick Installation Manual

Category
Security cameras
Type
Quick Installation Manual

This manual is also suitable for

EN
DE
FR
Quick Installation Guide
1/3” HDcctv Camera, WDR,
Day&Night, 1920x1080, 3x
AF Zoom, 12/24V
HDC-2080Z03 D (3-9mm)
HDC-2180Z03 D (9-22mm)
2
Table of content
Notes on safety .............................................................................................................3
Parts supplied ...............................................................................................................3
Part names .....................................................................................................................4
Installation instructions ...............................................................................................6
Power supply connections .............................................................................................................................................6
Set the video format according to system, EX-SDI or HD-SDI ........................................................................... 6
Operating instructions .................................................................................................8
Using OSD controller........................................................................................................................................................8
Description of the joystick operation ..........................................................................................................8
Description of the ZOOM&FOCUS adjustment .......................................................................................8
OSD menu startup ............................................................................................................................................................8
Direct control menu .........................................................................................................................................................9
Further information ......................................................................................................9
3
EN
Parts supplied
Zoom box camera
Operating instructions
Notes on safety
Please also pay attention to the enclosed safety instructions, and carefully read through
this instruction guide before initial operation.
Important points of warning are marked with a caution symbol.
i
Important points of advice are marked with a notice symbol.
4
Part names
¨
¥
¤
¢
¦
§
£
Mount Holes (Top / Bottom)
Rear Case
Front Case
Window
5
EN
B OSD Control Joy stick
C Power input terminal (AC24V/DC12V or DC12V)
D RS-485 / IR connector
E HD-SDI/EX-SDI output connector
F Power LED
G CVBS output connector
H Video format Switch
6
Installation instructions
CAUTION: The mounting bracket should be attached to a struc-
tural object, such as concrete, hard wood, wall stud or ceiling
rafter that supports the weight of the camera. If necessary use
appropriate mounting material (e.g. anchors) instead of the
material enclosed with the mounting bracket.
Make sure the power is removed before the installation.
Follow the order for applying power.
First connect the low voltage (DC12V or AC24V), then plug the AC adapter to AC
outlets to avoid an improper reset from power jitter and a damage from the surge
voltage when no load.
Mount the camera to the wall or ceilling with a corresponding mounting bracket
through the camera mount holes (1/4" thread insert) on its top or bottom.
CAUTION:
Care should be taken the cable is NOT to be damaged, kinked or
exposed in the hazardous area.
Do not expose the camera directly to a strong light source such
as the sun or spot light.
Power supply connections
Make sure the power is removed before the installation. Camera can work with either
24AC or 12VDC, dual voltage power. Primary and secondary grounds are completely
isolated to avoid the possible ground-loop problems.
i
In case that HD-SDI/EX-SDI Inputs are not supported in monitor, please use HD-SDI/
EX-SDI Converter to connect HD-SDI/EX-SDI cable with monitor. Some computer moni-
tors or TVs may not support 30p/25p. In this case, HD-SDI/EX-SDI DVR which can convert
the frame rate to 60p/50p is highly recommended. Please check specication of monitor
before installation.
Set the video format according to system, EX-SDI or HD-SDI
To select the cameras output video format (EX-SDI or HD-SDI), use the Video format
Switch on the side of the camera. Only one format can be used at a time (see also “Using
OSD controller”).
8
Operating instructions
Using OSD controller
Setup menu can be accessed and controlled by OSD control joy stick on the side of cam-
era unit. Five commands are available with the joy stick.
Description of the joystick operation
1. SET Key () : Access to the menu or enter the setting. To enter the main menu,
press the Set Key down for about 1.5sec
2. UP/DOWN Key (/) : Choose the desired sub-menu and to move the cursor up or
down.
3. LEFT/RIGHT Key (/) : Set up the value of the selected menu. Used to adjust the
desired menu selection and to move the cursor left or right.
4. denotes the long press down straightly for about 2 seconds
Description of the ZOOM&FOCUS adjustment
i
Works only when OSD Menu is inactive.
1. : Zoom In
2. : Zoom Out
3. ◄ : Focus Near
4. ► : Focus Far
OSD menu startup
Press ‘ (OSD menu Joy stick key) down for about 2 seconds to access the setup menu
mode.
i
Lens Initializing is strongly recommended at the rst stage of setup menu control.
ZOOM/FOCUS > LENS INIT > Press the joystick straight down for about 2 seconds.
9
EN
Further information
The manual is available from the eneo web site at www.eneo-security.com or from the CD
supplied with this product.
MENU V5.xx
1. ZOOM/FOCUS
2. EXPOSURE
3. SCENE ENHANCE
4. 3D-NR
5. DAY/NIGHT
6. PICT ADJUST
7. SPECIAL
8. SYSTEM
9. EXIT
NORMAL
MID
EXT
SAVE&EXIT
Direct control menu
MAIN DEFAULT DESCRIPTION
ZOOM/FOCUS - Sets FOCUS and ZOOM relative functions.
EXPOSURE - Sets EXPOSURE MODE, BRIGHTNESS, SENS-UP, AGC and MOTION DEBLUR.
SCENE ENHANCE NORMAL
SCENE ENHANCE provides the several ways to enhance the video in the various environments with
the settings in NORMAL, WDR, D-WDR, BLC and HLC.
3D-NR MID Sets 3DNR level. LOW, MID, HIGH
DAY/NIGHT EXT or AUTO
Sets DAY / NIGHT to EXT, AUTO, COLOR, B/W and COLOR D/N. Setting EXT mode for cameras with
IR-LED, AUTO mode for none IR-LED camera types.
PICT ADJUST Sets WHITE BAL, SHARPNESS, COLOR GAIN, GAMMA
SPECIAL Sets MIRROR/FLIP, PRIVACY, MOTION, PIXEL DEFECT, TITLE SET DISPLAY, DEFOG, POINTING ZOOM
SYSTEM Sets TV SYSTEM, RESOLUTION, COMM.SETUP, LANGUAGE an FACTORY DEFAULT
EXIT
SAVE & EXIT – Exits the menu after saving the parameters. EXIT – Exits the menu without saving
the menu.
eneo® is a registered trademark of
VIDEOR E. Hartig GmbH
Exclusive distribution through specialised
trade channels only.
VIDEOR E. Hartig GmbH
Carl-Zeiss-Straße 8
63322 Rödermark/Germany
Tel. +49 (0) 6074 / 888-0
Fax +49 (0) 6074 / 888-100
www.videor.com
www.eneo-security.com
Technical changes reserved
© Copyright by VIDEOR E. Hartig GmbH
Version 05/2015
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Eneo HDC-2080Z03 Quick Installation Manual

Category
Security cameras
Type
Quick Installation Manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages